C8051F331-GM - 25MHz 8-Bit Mixed-Signal MCU | Silicon Labs
MPN: C8051F331-GM ✓ AktifC8051F331-GM Ringkasan
A mixed-signal microcontroller is an embedded semiconductor that combines a digital processor with analog and timing peripherals on one device. In the product hierarchy, the C8051F331 belongs to the 8051 family of 8-bit microcontrollers, while the C8051F33x series adds flash programmability, on-chip analog conversion, and mixed-signal processing for compact control systems.
The C8051F331-GM reaches up to 50 MIPS using its 8051 core and includes 8 KB of flash plus 768 bytes of SRAM. Its operating voltage of 2.7 V to 3.6 V suits low-voltage embedded equipment, while port inputs tolerate signals up to 5 V. The two C2 interface pins can be shared with user functions, allowing in-system debugging without dedicating separate package pins.
The integrated mixed-signal resources make the C8051F331 suitable for products that must measure analog inputs while executing embedded control logic. Its 25 MHz processing rate, 8-bit architecture, and compact 20-pin MLP footprint provide a practical combination for sensor acquisition, signal conditioning, actuator control, and communication-enabled instrumentation.
Typical uses include industrial sensor controllers, compact data-acquisition modules, temperature-measurement instruments, low-power monitoring equipment, and small motor-control boards. Developers can use the C2 interface for programming and debugging, while the flash program memory supports field updates when the application design includes a suitable update mechanism.
PCB design should preserve the exposed-pad thermal and electrical requirements of the MLP package and provide clean grounding beneath the device. Decoupling should be placed close to the supply pins, and the 5 V-tolerant inputs should not be used as a substitute for a properly regulated 2.7 V to 3.6 V device supply.
This product page combines the manufacturer specifications with package, procurement, replacement, and application guidance. It also distinguishes verified drop-in candidates from devices whose peripheral mapping or package details require an engineering review before substitution.
Pilihan pengganti yang segera untuk C8051F331-GM — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera C8051F331-GM (sama faktor bentuk dan kaki) — berbeza dalam Flash Memory, Package.
C8051F330-GM
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →C8051F336-GMR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
C8051F313-GM
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
C8051F333-GM
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
C8051F334-GM
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
C8051F335-GM
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
C8051F331-GM Penilaian maksimum & Ciri-ciri Elektrik
| Core Architecture | 8051 8-bit core |
| Frekuensi Klock Maksimum | 25 MHz |
| Maximum Instruction Rate | 50 MIPS |
| Flash Memory | 8 KB (8K x 8) |
| SRAM | 768 bytes |
| Operating Voltage | 2.7 V to 3.6 V |
| Industrial Temperature Range | -40 °C to +85 °C |
| Kemasan | 20-pin MLP, 4 mm x 4 mm |
| Jenis Pemasangan | Surface mount |
| Programming and Debug Interface | C2 interface |
| C2 Interface Pin Count | 2 pins |
| Port Input Logic Tolerance | Up to 5 V |
Panduan Konfigurasi Pin C8051F331-GM 20-pin mlp, 4 mm x 4 mm
Konfigurasi pin untuk C8051F331-GM (20-pin mlp, 4 mm x 4 mm pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk C8051F331-GM.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
C8051F331-GM patut untuk 6 aplikasis: Industrial Sensor Controller, Compact Data Acquisition Module, Temperature and Environmental Monitoring, Low-Power Monitoring Equipment, Small Motor and Actuator Control, Communication-Enabled Embedded Instrument.
Industrial Sensor Controller
The C8051F331-GM fits compact industrial sensor controllers that need local measurement, control logic, and field programmability without a large processor. Its 25 MHz 8-bit core supports up to 50 MIPS, while 8 KB of flash and 768 bytes of SRAM provide room for acquisition routines and supervisory logic. The 2.7 V to 3.6 V operating range and -40 °C to +85 °C temperature specification suit low-voltage industrial equipment. Place the MCU beside the sensor interface, keep analog routing away from the C2 debug activity, and use a stable low-noise supply to preserve measurement quality.
Disebarkan
Compact Data Acquisition Module
The C8051F331-GM is appropriate for a compact data-acquisition module that samples sensors, performs scaling, and forwards processed readings. Its mixed-signal 8051 architecture places an 8-bit processor and analog resources in a 20-pin MLP package measuring 4 mm by 4 mm. The 25 MHz clock supports deterministic control tasks, while 8 KB of flash accommodates firmware and calibration tables. The 768-byte SRAM limit requires careful buffering for high-rate acquisition, so use interrupt-driven sampling and avoid retaining large intermediate datasets in memory.
Disebarkan
Temperature and Environmental Monitoring
The C8051F331-GM can serve as the control center in a temperature or environmental monitoring product that periodically reads sensors, applies thresholds, and manages alarms. Its 8 KB flash supports event handling and configuration storage, while the 768-byte SRAM is sufficient for short measurement cycles and filtered values. The industrial temperature range of -40 °C to +85 °C allows deployment in protected equipment, although the enclosure and sensor placement must control thermal gradients. Keep high-current switching nodes away from sensitive analog inputs and validate the complete acquisition path before calibration.
Disebarkan
Low-Power Monitoring Equipment
The C8051F331-GM is well suited to battery-operated monitoring equipment where an 8-bit mixed-signal controller can reduce system complexity. It combines a 25 MHz processing core, 8 KB of flash, and 768 bytes of SRAM while operating from 2.7 V to 3.6 V. Firmware can use low-power modes between sensor measurements, then activate the analog interface and communication path only when required. Because sleep-mode current and wake-up timing are not specified in the product listing, consult the family datasheet before defining the battery-life budget.
Disebarkan
Small Motor and Actuator Control
The C8051F331-GM can control small motors, relays, or other actuators in a compact embedded mechanism. Its 25 MHz 8-bit core provides fast digital sequencing, and the mixed-signal resources can support feedback measurement alongside control functions. The 768-byte SRAM limits complex motion algorithms, so simple state machines and timer-driven commutation are more appropriate. Drive inductive loads through suitable external circuitry rather than device pins, isolate switching transients from the analog section, and provide local bulk and bypass capacitance at the power entry point.
Disebarkan
Communication-Enabled Embedded Instrument
The C8051F331-GM can serve as the local controller in a compact measurement instrument that combines sensor conditioning, menu logic, and a communication interface. Its 8 KB flash and 768-byte SRAM are appropriate for lightweight protocols and deterministic control functions rather than heavy connectivity stacks. The two-pin C2 interface supports in-system programming and debugging and can be shared with user functions, reducing the number of dedicated package pins. Ensure the selected interface driver fits the available SRAM and that its timing does not interfere with critical sampling periods.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk C8051F331-GM — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | C8051F330-GM | C8051F336-GMR | C8051F313-GM | C8051F333-GM | C8051F334-GM | C8051F335-GM |
|---|---|---|---|---|---|---|---|
| Package | 20-pin MLP (4x4 mm) | 20-pin MLP (4x4 mm) | 20-pin MLP (4x4 mm) | 20-pin MLP (4x4 mm) | 20-pin MLP (4x4 mm) | 20-pin MLP (4x4 mm) | 20-pin MLP (4x4 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
Penyeberangsung Jelas
- Identified 25 MHz and 8 KB flash family match (vsC8051F330-GM)
- Compact 20-pin mixed-signal implementation (vsC8051F313-GM)
- C2 debugging with shared interface pins (vsC8051F336-GMR)
Catatan Desain
Use the exposed-pad land pattern and thermal-via arrangement shown in the Silicon Labs C8051F33x package drawing. The MLP body is only 4 mm by 4 mm, so placing bypass capacitors directly beside the supply and ground pins is important for transient response. Keep analog inputs away from the C2 clock signal and switching-node copper, and provide a continuous ground reference beneath the exposed pad where the package guidance permits.
Operate the C8051F331-GM from a regulated 2.7 V to 3.6 V rail. The 5 V tolerance applies to designated port inputs, not the supply pins, so external 5 V signals must be checked against the individual pin limits and leakage characteristics. Place high-value ceramic bypass capacitance close to the device and route transient current away from analog-reference paths to prevent measurement noise from coupling through shared supply impedance.
Do not select a family member solely because it has a 20-pin MLP package. Verify every analog-channel assignment, port multiplexing option, C2 connection, ground reference, and exposed-pad function against the target schematic. The 768-byte SRAM also limits buffering strategy: use interrupt-driven acquisition or streaming rather than storing large sample arrays, and retest firmware whenever a different C8051F33x device changes peripheral registers or interrupt vectors.
Preserve access to the two C2 pins even though they can be shared with user functions. The programming adapter must be able to drive and sense those signals without disconnecting the product circuitry. Avoid long traces from the debug interface into sensitive analog areas, and establish a solid return path for both C2 clock and data. This reduces susceptibility to crosstalk during programming and improves debug reliability in production units.
Maklumat Kesediaan
The device is specified for industrial-temperature operation from -40 °C to +85 °C. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer or current product documentation.