DG417CY+T - 35Ω SPST Analog Switch | Analog Devices
MPN: DG417CY+T ✓ AktifDG417CY+T Ringkasan
An analog switch is an integrated semiconductor device that routes a signal between circuit nodes under digital control. The DG417 belongs to the analog-switch hierarchy, which sits within interface ICs and broader semiconductor signal-path systems. Unlike a mechanical relay, a CMOS analog switch operates quickly, consumes little power, and can place very low resistance between a signal terminal and the common terminal. Its normally closed configuration provides a default electrical path when the control input is inactive.
Key characteristics include one SPST channel, a 35Ω specified on-resistance, and an 8-SOIC footprint. The DG417 family also guarantees on-resistance matching to 3Ω maximum between switches and on-resistance flatness to 4Ω maximum over the signal range. These matching and flatness limits are important in instrumentation because they reduce gain error and distortion when signals pass through the switch. The redesigned family additionally features low charge injection, low power consumption, and symmetrical bidirectional conduction.
The switch is specified for dual supply operation from ±4.5V to ±20V and for positive supply operation from +10V to +30V, depending on the device variant and test condition. These ranges permit operation from common laboratory and industrial supply rails while supporting bipolar signal paths. A separate negative supply is required when the switched signal can extend below ground. The CMOS construction controls power consumption while providing low off leakage and low on-resistance.
Typical uses include precision test-and-measurement signal paths, data-acquisition systems, analog input selection, automated test equipment, and instrumentation requiring a default closed connection. The switch can also provide sample-and-hold isolation, signal isolation, or a selectable resistive branch when its on-resistance is intentionally placed in the signal path. Symmetrical conduction is useful when the source impedance is not known in advance or when either signal polarity must be handled consistently.
For layout, keep the switched traces short and connect the common and terminal pins with symmetric routing where signal integrity matters. The control input must transition cleanly between valid logic levels, and unused supply pins must meet the requirements defined in the manufacturer datasheet. Because the 35Ω resistance is appreciable for precision measurement paths, account for it in gain, bandwidth, offset, and noise calculations rather than treating the closed switch as ideal.
This page combines manufacturer specifications, application guidance, pin-level design considerations, and a structured comparison of verified same-package alternatives. It helps engineers distinguish electrical drop-in options from merely similar interface switches and identify the correct replacement for an existing 8-SOIC layout.
Pilihan pengganti yang segera untuk DG417CY+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera DG417CY+T (sama faktor bentuk dan kaki) — berbeza dalam On-Resistance, On-Resistance Flatness, On-Resistance Matching, Package, Switch Configuration.
DG417CY+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DG417DY+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →DG417EY+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ADG417BRZ-REEL
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG417LDY-T1
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG417CY+T Penilaian maksimum & Ciri-ciri Elektrik
| Switch Configuration | 1 × SPST, normally closed |
| Number of Channels | 1 circuit |
| On-Resistance | 35 Ω |
| On-Resistance Matching | 3 Ω maximum |
| On-Resistance Flatness | 4 Ω maximum over the signal range |
| Conduction Direction | Bidirectional |
| Technology | Precision CMOS monolithic |
| Positive Supply Range | +10 V to +30 V |
| Dual Supply Range | ±4.5 V to ±20 V |
| ESD Tolerance | 2000 V minimum |
| Charge Injection | Low |
| Power Consumption | Low |
| Kemasan | 8-pin SOIC |
| Jenis Pemasangan | Surface mount |
| Status RoHS | Compliant |
| Lead-Free Status | Lead free |
Panduan Konfigurasi Pin DG417CY+T 8-pin soic
Konfigurasi pin untuk DG417CY+T (8-pin soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DG417CY+T.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DG417CY+T patut untuk 6 aplikasis: Automated Test Equipment Signal Routing, Precision Data Acquisition Multiplexing, Instrumentation Signal Isolation, Analog Input Selection, Low-Power Sensor Interface, Industrial Control Signal Switching.
Automated Test Equipment Signal Routing
The DG417CY+T fits automated test equipment that routes one precision measurement channel between a common terminal and an instrument or DUT connection. Its single normally closed SPST path provides a defined default route when the control signal is inactive, while the manufacturer guarantees on-resistance matching to 3Ω maximum and flatness to 4Ω maximum across the signal range. These limits help control channel-to-channel gain variation in measurement systems. Because the switch contributes 35Ω when closed, designers should include that resistance in the source impedance, attenuation, and noise calculations before setting the input impedance of the instrument.
Disebarkan
Precision Data Acquisition Multiplexing
The DG417CY+T can isolate or select a signal path in a precision data-acquisition front end where one switched terminal connects to a common measurement input. The 35Ω on-resistance must be included in the acquisition system’s input-impedance design, but the specified on-resistance matching and flatness help maintain more consistent channel behavior. Low charge injection is particularly useful when the switch is used around a sampling or hold stage because it reduces control-dependent timing shifts. A negative supply should be provided when measured nodes can fall below ground, and the control input should be driven with levels that meet the manufacturer’s absolute-maximum and operating conditions.
Disebarkan
Instrumentation Signal Isolation
For instrumentation signal isolation, the DG417CY+T provides a compact, low-power CMOS switch that disconnects a sensitive node when the control state calls for isolation. Its normally closed configuration makes it useful when a default connection is preferred, while symmetry of conduction reduces sensitivity to the source signal’s polarity. The device’s 35Ω path resistance can affect source loading, so high-impedance sensing should be placed downstream or selected with enough input impedance to limit the resulting error. Supply rails must support the full bipolar signal excursion, and control traces should be kept away from sensitive switched nodes to reduce coupling.
Disebarkan
Analog Input Selection
The DG417CY+T can implement a selectable analog-input branch by placing its common terminal on the signal path and assigning the switched terminal to the desired source. The low-power CMOS architecture is suitable for compact measurement systems, and the 3Ω maximum on-resistance matching and 4Ω maximum flatness help preserve consistent behavior as the selected input changes. Unlike a multiplexer, this is a single SPST channel, so additional switches or routing stages may be required for multiple simultaneous inputs. The 35Ω on-resistance remains the principal closed-path error and should be included in transfer-function calculations.
Disebarkan
Low-Power Sensor Interface
The DG417CY+T can control a low-leakage connection in a sensor interface where the switch must remain compatible with small signal levels and limited power budgets. Its CMOS implementation offers low power consumption, while the normally closed path can support a default sensor connection. Low charge injection helps when the controlled node is connected to a sampling capacitor or high-impedance amplifier. Leakage and charge injection remain design-dependent, so the complete electrical characteristic set in the manufacturer datasheet should be checked against the sensor source impedance, cable capacitance, and acquisition timing.
Disebarkan
Industrial Control Signal Switching
The DG417CY+T is applicable to industrial control and test interfaces that need a compact analog routing element between a controller and a signal-conditioning stage. Its dual-supply capability of ±4.5V to ±20V supports bipolar control and measurement environments, while the positive-only range of +10V to +30V supports common industrial rails for compatible positive signals. The device conducts equally well in either direction, which simplifies circuits where the signal source polarity may vary. Designers should verify the exact DG417CY+T operating-temperature grade and provide stable supply bypassing at the package pins.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DG417CY+T — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DG417CY+ | DG417DY+ | DG417EY+ | ADG417BRZ-REEL | DG417LDY-T1 |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology |
Penyeberangsung Jelas
- Established DG417 precision-switch performance (vsADG417BRZ-REEL)
- Lower stated on-resistance in the same 8-SOIC footprint (vsDG417LDY-T1)
- Direct ordering equivalence (vsDG417CY+)
Catatan Desain
Treat the closed switch as a 35Ω series resistance rather than an ideal conductor. Include this resistance in the source-load interaction, attenuation, noise, and settling calculations. In measurement applications, the manufacturer’s limits of 3Ω maximum on-resistance matching and 4Ω maximum flatness are more useful than the nominal resistance alone because they describe variation across the DG417 family and signal range.
Route the switched terminals and common terminal as short, compact traces, and place supply bypass capacitors close to the device power pins. Keep the control trace away from sensitive switched nodes where practical. A symmetric layout reduces parasitic differences between terminal paths, while minimizing loop area around the switch improves immunity to coupled noise and reduces the possibility of unintended transient coupling into the signal path.
Confirm the control-logic polarity and normally closed state from the manufacturer pin-description table before finalizing the PCB. Do not assume that two 8-pin SOIC analog switches are interchangeable because their packages match. Validate pin names, supply requirements, logic thresholds, maximum switch voltage, on-resistance, leakage, bandwidth, and charge injection before replacing DG417CY+T with another device.
Provide the required positive and negative supply rails with adequate bypassing before applying a bipolar signal. The device supports positive-only and dual-supply operating ranges, but the applicable limits depend on the exact DG417CY+T configuration. Verify startup, input-voltage tolerance, and absolute-maximum conditions in the manufacturer datasheet. Control signals should remain within their specified voltage limits even when the analog node is exposed to a transient.
Maklumat Kesediaan
The manufacturer-linked product information identifies RoHS compliance and lead-free construction. Other compliance attributes are not stated and remain unknown.