Analog Devices

LT1222IS8 - 500MHz Low-Noise Op Amp | Analog Devices

MPN: LT1222IS8 ✓ Aktif
3 nV/√Hz Vdss 8-pin SO Package
MOQ: 1 |

LT1222IS8 Ringkasan

Analog Devices LT1222IS8 is a low-noise, very-high-speed operational amplifier with a 500 MHz gain-bandwidth product, 3 nV/√Hz input-noise voltage density, and 200 V/µs slew rate in an 8-pin SO package. The LT1222IS8 is a single-amplifier device intended for instrumentation and signal-processing applications that require both wide bandwidth and low noise. It is stable at a noise gain of 10 or greater without external compensation.

An operational amplifier is an analog amplifier that uses differential feedback to control gain, bandwidth, and output behavior. Within the semiconductor hierarchy, the LT1222IS8 is a voltage-feedback operational amplifier, a type of analog integrated circuit used for precision signal conditioning, current-voltage conversion, buffering, and gain control. Its combination of high speed and low noise places it between general-purpose precision amplifiers and wideband instrumentation amplifiers.

Principal features include a 500 MHz gain-bandwidth product, 200 V/µs slew rate, and input noise density of 3 nV/√Hz. The device is stable without compensation at noise gains of 10 or higher. For lower closed-loop gains, external compensation can be used, although bandwidth and slew-rate performance are reduced. The LT1222IS8 also provides improved DC characteristics relative to earlier high-speed amplifiers, including reduced input offset voltage and lower input bias current.

The architecture combines low-noise bipolar input behavior with wideband frequency response. Noise-gain stability is important in practical layouts because feedback resistors determine both closed-loop gain and the minimum noise gain. Capacitive-load drive and external compensation provide additional control when driving cables, ADC input networks, or other nonideal loads. The maximum input offset voltage listed for the device is 300 µV, making it more appropriate for fast signal paths than for ultra-high-accuracy DC measurements requiring nanovolt-level offsets.

Typical uses include low-noise instrumentation front ends, high-speed instrumentation amplifiers, active filters, pulse-shaping circuits, video and communication signal conditioning, photodiode amplification, and high-speed data-acquisition interfaces. In these systems, the 500 MHz bandwidth preserves short rise times, while 3 nV/√Hz input noise limits the amplifier's contribution to weak-signal measurement noise. The 200 V/µs slew rate also helps preserve amplitude accuracy when large input steps must be reproduced quickly.

Designers should place input and feedback components close to the amplifier, minimize parasitic capacitance, and use short, properly terminated output paths. Avoid standard 0.1 µF decoupling capacitors directly at high-speed signal pins because their effective impedance and instability can degrade the response. Confirm stability with the actual source impedance, load capacitance, and feedback network before increasing bandwidth or operating at low noise gains.

This product page brings together the manufacturer's operating characteristics, orderable same-family alternatives, package details, and practical high-speed layout guidance. It also distinguishes electrically similar suffixes from lower-gain or differently compensated devices so engineers can verify pin compatibility, temperature grade, and bandwidth before making a board-level substitution.

Pilihan pengganti yang segera untuk LT1222IS8 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

LT1222IS8#PBF

✅ Masuk Drop-In
📦 8-pin SO
Same LT1222IS8 core ratings of 500 MHz and 3 nV/√Hz; the orderable code adds the #PBF lead-free finish, with 0% difference in the identified key parameters.

📋 Alternatif rujukan (tidak dalam katalog)

LT1222IS8#TRPBF

✅ Masuk Drop-In
📦 8-pin SO
Same LT1222IS8 500 MHz bandwidth and 3 nV/√Hz noise specifications; #TR identifies a tape-and-reel orderable code with no identified change to the core electrical ratings.

📋 Alternatif rujukan (tidak dalam katalog)

LT1222IS8#TR

✅ Masuk Drop-In
📦 8-pin SO
Same LT1222IS8 500 MHz bandwidth and 3 nV/√Hz noise specifications; #TR identifies the non-PBF tape-and-reel orderable code with no identified electrical change.

📋 Alternatif rujukan (tidak dalam katalog)

LT1222CS8

✅ Masuk Drop-In
📦 8-pin SO
Same 500 MHz gain-bandwidth product and 3 nV/√Hz input noise, but the commercial C temperature grade differs from the I grade; the exact temperature limits must be confirmed before substitution.

📋 Alternatif rujukan (tidak dalam katalog)

LT1222

✅ Masuk Drop-In
📦 8-pin SO
Base LT1222 family designation with the identified 500 MHz bandwidth and 3 nV/√Hz noise performance; the exact package suffix and temperature grade must be confirmed before ordering.

📋 Alternatif rujukan (tidak dalam katalog)

LT1222IS8 Penilaian maksimum & Ciri-ciri Elektrik

Product Type Single low-noise high-speed operational amplifier
Amplifier Circuit Count 1 circuit
Gain-Bandwidth Product 500 MHz
Slew Rate 200 V/µs
Input Noise Voltage Density 3 nV/√Hz
Minimum Uncompensated Noise Gain 10
Maximum Input Offset Voltage 300 µV
Operating Ambient Temperature -40 °C to +85 °C
Kemasan 8-pin SO
Jenis Pemasangan Surface mount
Input Transistor Type Bipolar
External Compensation Supported for closed-loop gains below 10
Capacitive Load Drive C-Load operational amplifier

Konfigurasi Pin LT1222IS8

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OFFSET NULL — Offset-voltage null connection
Pin 2 INPUT — Inverting input
Pin 3 INPUT — Non-inverting input
Pin 4 V− — Negative supply voltage
Pin 5 COMP — External compensation connection
Pin 6 OUTPUT — Amplifier output
Pin 7 V+ — Positive supply voltage
Pin 8 COMP — External compensation connection

Aplikasi Biasa

LT1222IS8 patut untuk 6 aplikasis: Low-Noise Instrumentation Front End, High-Speed Data Acquisition, Photodiode Signal Conditioning, Active Filtering and Equalization, Pulse and Waveform Conditioning, Video Signal Amplification.

🏭

Low-Noise Instrumentation Front End

The LT1222IS8 fits instrumentation front ends that must preserve both small-signal amplitude and timing information. Its 3 nV/√Hz input-noise density limits amplifier-added noise, while the 500 MHz gain-bandwidth product supports fast sensor signals without imposing a narrow-band penalty. The 200 V/µs slew rate also reduces large-step distortion when the input changes quickly. In a typical amplifier, the feedback network establishes the closed-loop gain, while the signal is routed over short, guarded traces to minimize parasitic pickup and capacitance. Because the LT1222 is uncompensated, noise gain should remain at 10 or greater unless the external compensation values specified by Analog Devices are implemented.

🖥️

High-Speed Data Acquisition

The LT1222IS8 can serve as the final voltage-gain stage in a wideband data-acquisition channel. The 500 MHz gain-bandwidth product allows the amplifier to pass high-frequency signal content, while 3 nV/√Hz noise keeps its contribution low relative to many precision input stages. Its 200 V/µs slew rate supports large, fast transitions without severe amplitude loss. Place the device close to the acquisition IC or connector, keep feedback loops compact, and use a controlled ground return to minimize high-frequency noise coupling. Gain and source impedance must also be checked against the uncompensated stability requirement before the sampling bandwidth is finalized.

🧩

Photodiode Signal Conditioning

The LT1222IS8 is appropriate for fast photodiode current-to-voltage conditioning where the sensor output can be both small and rapidly changing. Its 3 nV/√Hz input-noise density supports low-level optical measurements, while its 500 MHz bandwidth preserves pulse edges and the 200 V/µs slew rate improves large-signal reproduction. A typical transimpedance stage requires careful feedback-resistor selection, low parasitic capacitance around the summing node, and controlled grounding to prevent unintended oscillation. Since the LT1222 is stable without compensation at noise gains of 10 or higher, the transimpedance network must preserve that condition or use the manufacturer's external-compensation approach.

🌐

Active Filtering and Equalization

The LT1222IS8 can implement active filters and equalization stages extending into the high-frequency region. Its 500 MHz gain-bandwidth product provides the required closed-loop bandwidth, while the 200 V/µs slew rate reduces distortion when multiple filter stages receive large or abrupt inputs. The 3 nV/√Hz noise density is also beneficial when the filter handles weak signals rather than only high-level communications waveforms. Component tolerances, parasitic capacitance, and amplifier input impedance can shift the filter response, so final poles and Q should be calculated with realistic component models. For low noise gains, external compensation must be selected according to the Analog Devices compensation guidance.

📺

Pulse and Waveform Conditioning

The LT1222IS8 is well suited to shaping fast pulses or correcting waveform distortion because its 500 MHz bandwidth and 200 V/µs slew rate preserve short transitions. The 3 nV/√Hz input-noise density is useful when the waveform contains low-level information riding on larger transitions. The amplifier can be used as a non-inverting or inverting gain stage, provided the feedback network maintains a noise gain of at least 10 for uncompensated operation. Keep the feedback components close to the pins, minimize output trace length, and verify the load because capacitive loading can alter stability and reduce usable bandwidth.

🎥

Video Signal Amplification

The LT1222IS8 can amplify video-rate signals when bandwidth and slew-rate margin are more important than ultra-low DC offset. Its 500 MHz gain-bandwidth product exceeds the bandwidth of many standard-definition video signals, while the 200 V/µs slew rate provides useful rise-time capability for higher-bandwidth composite or component video paths. The 3 nV/√Hz noise density can benefit low-level video signals, although system noise and video-chain bandwidth generally dominate practical results. Use short PCB traces, a solid ground plane, and appropriately terminated input and output networks. Confirm the required gain, source impedance, and capacitive load before treating the amplifier as a direct video-buffer solution.

Ringkasan Produk Disebarkan

LT1222IS8#PBF Lead-free orderable configuration of the same amplifier Dipergunakan di: Low-Noise Instrumentation Front End, High-Speed Data Acquisition, Photodiode Signal Conditioning, Pulse and Waveform Conditioning LT1222CS8 Same-family amplifier for an alternative temperature grade Dipergunakan di: Low-Noise Instrumentation Front End, Photodiode Signal Conditioning, Video Signal Amplification LT1222IS8#TRPBF Tape-and-reel orderable LT1222IS8 configuration Dipergunakan di: High-Speed Data Acquisition, Active Filtering and Equalization, Video Signal Amplification LT1222IS8#TR Same electrical amplifier in an alternate orderable format Dipergunakan di: Active Filtering and Equalization LT1222 Base family ordering designation Dipergunakan di: Pulse and Waveform Conditioning
What are the key specifications of LT1222IS8?
The LT1222IS8 is a single, low-noise operational amplifier with a 500 MHz gain-bandwidth product, 3 nV/√Hz input-noise density, and 200 V/µs slew rate. According to the Analog Devices LT1222 datasheet, it is stable without compensation at noise gains of 10 or higher and can be externally compensated for lower closed-loop gains. The device uses an 8-pin SO package and is specified for ambient temperatures from -40 °C to +85 °C.
What is the operating voltage range of LT1222IS8?
The operating supply-voltage range requires confirmation from the LT1222 datasheet before the device is placed in a circuit. The manufacturer identifies the LT1222IS8 as a single, bipolar, low-noise, high-speed operational amplifier in an 8-pin SO package, with 500 MHz gain-bandwidth product and 200 V/µs slew rate. Request the exact supply limits and input common-mode range through the Request a Quote form when the hardware revision or complete datasheet table must accompany a production order.
Is LT1222IS8 suitable for low-noise instrumentation?
Yes, the LT1222IS8 is suitable for instrumentation applications requiring low input noise and wide bandwidth. Its specified input-noise voltage density is 3 nV/√Hz, while its 500 MHz gain-bandwidth product and 200 V/µs slew rate allow the amplifier to process small signals without sacrificing transient response. According to the Analog Devices product description, the LT1222 also offers superior DC performance and lower input bias current than earlier high-speed operational amplifiers.
Can LT1222IS8 be used at closed-loop gains below 10?
Yes, but external compensation is required when the closed-loop gain is below 10. The LT1222 is uncompensated and stable at noise gains of 10 or greater. The Analog Devices datasheet states that external compensation permits lower closed-loop gains at the expense of bandwidth and slew rate. Component values must therefore be selected from the manufacturer's compensation tables for the intended gain and feedback topology.
What is the difference between LT1222IS8 and LT1222CS8?
The LT1222IS8 and LT1222CS8 share the same LT1222 family and 8-pin SO implementation, but their temperature grades differ. The I-grade LT1222IS8 is specified for -40 °C to +85 °C, while the C-grade LT1222CS8 uses a different manufacturer temperature-grade designation. Both retain the family's 500 MHz gain-bandwidth product and 3 nV/√Hz noise specification, but final qualification should be checked against the required ambient-temperature range.
When should I choose LT1222IS8 over a lower-speed precision op amp?
Choose the LT1222IS8 when the signal path needs both low noise and high bandwidth. A precision amplifier may offer lower offset or better DC accuracy, but the LT1222IS8 combines 3 nV/√Hz input noise with a 500 MHz gain-bandwidth product and 200 V/µs slew rate. This makes it more appropriate for fast instrumentation, active filtering, photodiode signals, and acquisition circuits where slow large-signal settling would distort the result.
What can replace LT1222IS8?
LT1222IS8#PBF is the closest same-family orderable alternative because it retains the LT1222IS8 electrical configuration and 8-pin SO footprint, with the #PBF lead-free finish reflected in its ordering code. LT1222CS8 is another same-package family option for a different commercial temperature grade. The Request a Quote form can confirm the exact suffix, quantity, and current availability for either configuration before a substitution is released to production.
Is LT1222IS8 the same as LT1222IS8#PBF?
The LT1222IS8 and LT1222IS8#PBF identify the same base LT1222IS8 device in 8-pin SO form, with #PBF indicating the orderable lead-free termination. The Analog Devices family literature and distributor records treat the base and #PBF ordering codes as closely related configurations rather than different amplifier architectures. Confirm the marking, temperature grade, and exact orderable MPN against the manufacturer's product page before updating a BOM.
Where can I download the LT1222IS8 datasheet PDF?
The official Analog Devices LT1222 datasheet PDF is available at https://www.analog.com/media/en/technical-documentation/data-sheets/1222fc.pdf. It contains the electrical characteristics, compensation information, package drawings, and ordering information for the LT1222 family. The linked manufacturer product page at analog.com/en/products/lt1222.html is also the appropriate starting point for current lifecycle and ordering-code information.
Where can I find the LT1222IS8 pinout?
The LT1222IS8 pinout is shown in the package and pin-function drawings in the official Analog Devices LT1222 datasheet. The device is an 8-pin SO operational amplifier. Use the pin-description table when assigning input, output, supply, ground, offset-null, and compensation connections, and preserve the package orientation indicated by the manufacturer's drawing rather than relying only on a generic SOIC footprint.
What is the best cross-brand equivalent for LT1222IS8?
No cross-brand drop-in equivalent can be confirmed from the available substitution records, so the LT1222IS8 should not be replaced with an unverified competitor part. A valid substitute would need the same 8-pin SO pinout, at least 10 noise-gain stability without compensation, comparable noise density, bandwidth, and slew rate. Use the Request a Quote form if your sourcing team requires a second-source proposal for qualification review.
How should LT1222IS8 be laid out for high-speed performance?
Keep the input, feedback, and compensation components close to the amplifier and minimize trace length around high-speed nodes. The LT1222's 200 V/µs slew rate and 500 MHz bandwidth make parasitic capacitance and poor grounding more significant than in low-frequency precision circuits. Use a clean ground reference, avoid unnecessary stub lengths, and validate the complete feedback network and load because compensation requirements depend on closed-loop gain.
Does LT1222IS8 require external compensation at gain 10?
No, the LT1222 is stable without compensation at a noise gain of 10 or greater. According to the Analog Devices LT1222 datasheet, the device can instead be externally compensated for lower closed-loop gains, with reduced bandwidth and slew rate as the trade-off. Designers should distinguish signal gain from noise gain because the stability requirement is specifically based on noise gain, including the contribution of the feedback network.
What is the lead time and stock status of LT1222IS8?
Current stock and lead time should be confirmed through the Request a Quote form on this page for the exact LT1222IS8 ordering configuration. Distributor records show active purchasing channels for the device, but that does not by itself guarantee a fixed warehouse quantity or delivery schedule for every order quantity. The quote request allows XAIPART to confirm the current manufacturing and distribution position without embedding a potentially stale availability claim.
Where can I buy LT1222IS8?
Use the Request a Quote form on this page to request LT1222IS8 availability, current commercial terms, and an order quotation. The part is an Analog Devices single operational amplifier in an 8-pin SO package, with a 500 MHz gain-bandwidth product, 3 nV/√Hz input-noise density, and 200 V/µs slew rate. Include the required quantity, target suffix, and production schedule so the quotation can be matched to the intended build.

Data referensi kejuruteraan untuk LT1222IS8 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the LT1222IS8 for wideband, low-noise analog signal paths that need 500 MHz gain-bandwidth product, 200 V/µs slew rate, and 3 nV/√Hz input-noise density in an 8-pin SO package. It is particularly suitable for instrumentation, photodiode amplifiers, active filters, waveform conditioning, and acquisition interfaces, provided the feedback network maintains a noise gain of 10 or greater or uses the manufacturer's external-compensation circuit. LT1222IS8#PBF is the preferred lead-free orderable configuration when the BOM requires that finish. LT1222IS8#TRPBF and LT1222IS8#TR provide corresponding tape-and-reel ordering formats, so their selection should be based on manufacturing requirements rather than an electrical difference. LT1222CS8 is appropriate only when its C temperature grade meets the environmental requirement. No cross-brand drop-in part is recommended without a separate pinout, stability, noise, bandwidth, and slew-rate qualification.

Perbandingan dengan Gantian

Parametr Produk Ini LT1222IS8#PBF LT1222IS8#TRPBF LT1222IS8#TR LT1222CS8 LT1222
Package 8-pin SO 8-pin SO 8-pin SO 8-pin SO 8-pin SO 8-pin SO option; confirm exact suffix
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Gain-Bandwidth Product 500 MHz 500 MHz 500 MHz 500 MHz 500 MHz 500 MHz
Slew Rate 200 V/µs 200 V/µs 200 V/µs 200 V/µs 200 V/µs 200 V/µs
Input Noise Voltage Density 3 nV/√Hz 3 nV/√Hz 3 nV/√Hz 3 nV/√Hz 3 nV/√Hz 3 nV/√Hz
Uncompensated Noise Gain 10 or greater 10 or greater 10 or greater 10 or greater 10 or greater 10 or greater
Operating Ambient Temperature -40 °C to +85 °C, I grade -40 °C to +85 °C, I grade -40 °C to +85 °C, I grade -40 °C to +85 °C, I grade C grade; confirm exact limits Grade depends on orderable suffix
External Compensation Supported for lower closed-loop gains Supported for lower closed-loop gains Supported for lower closed-loop gains Supported for lower closed-loop gains Supported for lower closed-loop gains Supported for lower closed-loop gains

Penyeberangsung Jelas

  • Combines very wide bandwidth with low input noise (vsLT1222CS8)
  • Lead-free orderable version preserves the complete LT1222IS8 function (vsLT1222IS8#PBF)
  • Production tape-and-reel configuration with unchanged core ratings (vsLT1222IS8#TRPBF)
  • External compensation enables lower-gain implementations (vsLT1222)

Catatan Desain

Keep the input, feedback, compensation, and grounding paths compact because the LT1222 has a 500 MHz gain-bandwidth product and 200 V/µs slew rate. Place input and feedback resistors close to their associated pins, avoid long loops, and route high-impedance input nodes with minimal exposed area. At these frequencies, PCB trace capacitance and inductance can alter stability or add noise even when the schematic is correct.

Do not assume that a low signal gain provides low noise gain. The uncompensated LT1222 requires a noise gain of 10 or greater for stable operation. If lower closed-loop gain is required, implement the manufacturer's external-compensation network and accept the corresponding reduction in bandwidth and slew rate. Always evaluate the final feedback values, source impedance, and load capacitance together rather than checking signal gain alone.

Avoid placing ordinary 0.1 µF ceramic bypass capacitors directly on sensitive high-speed amplifier pins unless their electrical behavior has been checked for the operating frequency. Their impedance and package inductance can create unintended feedback paths in a 500 MHz design. Use a low-inductance ground and supply arrangement, keep the output path short, and validate stability with the actual source and load rather than relying on an ideal simulation.

Treat the offset-null, compensation, input, output, and supply pins as separate high-speed nets even though they share a small package. Avoid long traces and unnecessary test-point stubs, particularly at the inverting input and compensation nodes. A resistive or inductive isolation element can be useful for debugging, but its value should be chosen with the target bandwidth in mind so that the added impedance does not disturb gain or phase margin.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The exact #PBF ordering code indicates a lead-free termination, but formal RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor records.

Data disahkan pada: 2026-11-14 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

LT1222IS8 datasheet LT1222IS8 pinout LT1222IS8 datasheet pdf LT1222IS8 equivalent LT1222IS8 replacement LT1222IS8 cross reference LT1222IS8 vs LT1222CS8 LT1222IS8 footprint LT1222IS8 spice model LT1222IS8 price LT1222IS8 stock Analog Devices LT1222IS8 LT1222 500MHz op amp LT1222 application circuit

Komponen dan Tanda berkaitan

Analog Devices LT1222 LT1222IS8 LT1222IS8#PBF LT1222IS8#TRPBF LT1222IS8#TR LT1222CS8 operational amplifier voltage-feedback amplifier analog integrated circuit semiconductor noise gain gain-bandwidth product input noise voltage density slew rate external compensation input offset voltage input bias current bipolar input 8-pin SO package SO package family surface-mount package instrumentation photodiode amplification active filtering
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ