LT1884IN8 - Dual 2MHz Picoamp Input Op Amp | Analog Devices
MPN: LT1884IN8 ✓ AktifLT1884IN8 Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to control gain, bandwidth, and output behavior. The LT1884 belongs to the precision operational-amplifier hierarchy within amplifier ICs, combining high input accuracy, rail-to-rail output swing, and relatively fast response for instrumentation and low-level signal-processing systems.
The LT1884 family provides two amplifiers per package, an input offset voltage trimmed to less than 50 µV, and a maximum input bias current of 400 pA. Its rail-to-rail output allows the output voltage to approach the supply limits, while the 2 MHz gain-bandwidth product and 0.9 V/µs slew rate support small-signal processing and low-frequency waveform applications.
Low input bias current is particularly important when the op amp senses currents from high-impedance sources, because bias current produces offset errors across the source impedance. Input offset drift preserves accuracy as temperature changes, while the combination of precision offset performance, rail-to-rail output, and a 2 MHz bandwidth makes the device suitable for sensor interfaces, current measurement, buffers, and general instrumentation.
Typical uses include precision current sensing, photodiode and other high-impedance sensor amplification, low-voltage signal conditioning, active filtering, and buffering. In each case, the 400 pA maximum bias current limits error generated by the sensing network, while the 0.9 V/µs slew rate helps preserve fidelity on small, rapidly changing signals.
Designers should verify the input common-mode range, output swing, supply-voltage limits, and stability requirements against the intended feedback network. Because the LT1884IN8 uses an 8-pin PDIP package, it is also appropriate for through-hole prototypes and legacy industrial boards that require this established footprint rather than a surface-mount redesign.
This page organizes the LT1884IN8 technical characteristics, temperature-grade alternatives, drop-in replacement options, and practical design considerations. It also distinguishes the dual 8-pin PDIP configuration from other LT1884 package and grade options so engineers can make a footprint-compatible sourcing decision before schematic capture.
Pilihan pengganti yang segera untuk LT1884IN8 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LT1884IN8 (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Input Offset Voltage, Mounting Type, Output Swing, Package.
LT1884CN8#PBF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1884AIN8#PBF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1884ACN8#PBF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1884IS8
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LT1884CS8#PBF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1884IN8 Penilaian maksimum & Ciri-ciri Elektrik
| Number of Amplifiers | 2 channels |
| Amplifier Type | 2 general-purpose precision operational amplifiers |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 0.9 V/µs |
| Input Offset Voltage | Less than 50 µV, trimmed |
| Input Bias Current | 400 pA maximum |
| Output Swing | Rail-to-rail output |
| Tegangan Pemberi Arus | ±18 V maximum total supply |
| Total Supply Voltage | 36 V maximum |
| Kemasan | 8-pin PDIP |
| Terminal Count | 8 pins |
| Jenis Pemasangan | Through-hole |
| Temperature Grade | Industrial |
| Termination Form | 8-pin PDIP |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Panduan Konfigurasi Pin LT1884IN8 8-pin pdip
Konfigurasi pin untuk LT1884IN8 (8-pin pdip pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LT1884IN8.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LT1884IN8 patut untuk 6 aplikasis: Precision Current Sensing, High-Impedance Sensor Interface, Photodiode Signal Conditioning, Active Filtering and Buffering, Industrial Measurement Instrumentation, Legacy Through-Hole Control Boards.
Precision Current Sensing
The LT1884IN8 fits precision current sensing because its maximum input bias current is only 400 pA and its input offset voltage is trimmed to less than 50 µV. These characteristics reduce errors when the amplifier senses the voltage across a high-value shunt or the current through a low-bias transducer. The dual configuration allows one channel to monitor a load while the other provides gain, filtering, or reference conditioning. Its 2 MHz gain-bandwidth product and 0.9 V/µs slew rate support responsive small-signal measurement, although the shunt impedance, common-mode voltage, amplifier noise, and feedback-network tolerances determine the final accuracy.
Disebarkan
High-Impedance Sensor Interface
A high-impedance sensor interface benefits from the LT1884IN8's ultra-low 400 pA maximum input bias current, which limits the voltage error introduced by bias current flowing through a high source resistance. The trimmed offset voltage of less than 50 µV also supports low-level sensor signals requiring accurate amplification. Designers can use the dual amplifiers for signal conditioning and a second gain or buffer stage. Because the operating bandwidth is 2 MHz with a 0.9 V/µs slew rate, the device suits sensors whose signals remain within that bandwidth, while guarding against sensor capacitance, board leakage, and the input common-mode range.
Disebarkan
Photodiode Signal Conditioning
The LT1884IN8 can condition weak photodiode currents because its maximum input bias current of 400 pA is small relative to many precision photodiode operating ranges. The two amplifiers allow a transimpedance stage and a subsequent voltage-gain or filtering stage to share one 8-pin PDIP package. Rail-to-rail output improves usable output range on low-voltage supplies, while the 2 MHz gain-bandwidth product and 0.9 V/µs slew rate support moderate-speed optical measurements. The actual photodiode capacitance and feedback resistor must be checked for stability, since parasitic capacitance can materially change closed-loop bandwidth even when the intrinsic amplifier specifications appear adequate.
Disebarkan
Active Filtering and Buffering
The LT1884IN8 is useful for active filtering and buffering in precision analog systems where low input bias current helps preserve high source impedance. Its rail-to-rail output allows the buffered signal to use much of the available output range, while the 2 MHz gain-bandwidth product provides useful bandwidth for low-frequency filters and general instrumentation. Both amplifiers are independent, allowing cascading filter sections or implementing a gain stage followed by a buffer. Component tolerances, amplifier noise, output-current capability, and stability with the selected load remain important; the 0.9 V/µs slew rate helps preserve fidelity when the filter passes small, fast-changing waveforms.
Disebarkan
Industrial Measurement Instrumentation
The LT1884IN8 suits industrial measurement instrumentation that combines a through-hole DIP-8 footprint with precision analog performance. Its less-than-50-µV trimmed offset and low drift help preserve accuracy as operating conditions change, while rail-to-rail output improves signal headroom in low-voltage measurement systems. The dual configuration supports two measurement channels or a differential conditioning arrangement. Its 2 MHz bandwidth and 0.9 V/µs slew rate are suitable for many process-control and laboratory signals, but engineers should verify the input common-mode range, supply limits, electromagnetic interference requirements, and temperature qualification for the installed industrial equipment.
Disebarkan
Legacy Through-Hole Control Boards
The LT1884IN8 is well suited to retrofit and prototype work on legacy through-hole control boards because it retains the 8-pin PDIP footprint and dual-amplifier configuration. This allows an existing analog conditioning section to be serviced or upgraded without converting the board to a fine-pitch surface-mount package. The part provides a 2 MHz gain-bandwidth product, 0.9 V/µs slew rate, rail-to-rail output, and 400 pA maximum input bias current for precision signal paths. Before substitution or repair, confirm the PCB pin mapping, power rails, feedback topology, common-mode range, and stability of surrounding compensation components against the manufacturer datasheet.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LT1884IN8 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LT1884CN8#PBF | LT1884AIN8#PBF | LT1884ACN8#PBF | LT1884IS8 | LT1884CS8#PBF |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Number of Amplifiers | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Input Offset Voltage | Less than 50 µV, trimmed | Less than 50 µV, trimmed | Less than 50 µV, trimmed | Less than 50 µV, trimmed | Less than 50 µV, trimmed | Less than 50 µV, trimmed |
| Maximum Input Bias Current | 400 pA | 400 pA | 400 pA | 400 pA | 400 pA | 400 pA |
| Temperature Grade | Industrial | Commercial | Industrial | Commercial | Industrial | Commercial |
Penyeberangsung Jelas
- Precision input behavior in a dual through-hole package (vsLT1884CN8#PBF)
- Direct DIP-8 retrofit without a package redesign (vsLT1884IS8)
- Low-bias dual signal conditioning (vsLT1884ACN8#PBF)
Catatan Desain
Check the complete manufacturer pin-connection table before laying out the DIP-8 footprint. The LT1884IN8 contains two independent amplifiers, and an incorrect assignment of output, feedback, input, or supply pins can produce saturation or unstable operation. Also verify the input common-mode range and output swing for the selected supply voltage; rail-to-rail output improves available signal range but does not remove all input-range limitations.
Treat the LT1884IN8 as a low-bias precision amplifier rather than a general high-speed op amp. Its 400 pA maximum input bias current is valuable with high-impedance sources, but PCB contamination, moisture, and leakage across sensitive input nodes can exceed that device-level limit. Use guarding where practical, keep input traces short, maintain a clean analog ground reference, and avoid routing sensitive inputs beside switching nodes or high-current return paths.
Decouple each supply rail near the IC with local high-frequency and bulk capacitance, and route each decoupling capacitor directly to the relevant power pin and ground reference. The LT1884 family supports rail-to-rail output, so headroom at the output can still be reduced by the load, output-current limit, temperature, and supply tolerance. Confirm those conditions against the manufacturer datasheet before relying on output swing close to a supply rail.
Keep feedback components close to the associated amplifier pins and use symmetrical routing when matching channels. The 2 MHz gain-bandwidth product makes stray PCB capacitance relevant in high-value feedback networks, particularly around photodiode or sensor inputs. If the circuit requires compensation beyond a simple resistive feedback network, follow the recommended compensation and stability guidance in the Analog Devices LT1884 datasheet rather than adding capacitance empirically.
Maklumat Kesediaan
The exact target ordering code does not carry the #PBF lead-free suffix. Lead-free treatment for identified alternatives differs by ordering code and must be confirmed against the manufacturer product documentation.