MAX3095CSE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MPN: MAX3095CSE+ ✓ AktifMAX3095CSE+ Ringkasan
An RS-422/RS-485 receiver is an interface integrated circuit that converts small differential voltage signals carried over a balanced cable into a logic-level output for a host controller. In the broader hierarchy, the MAX3095CSE+ belongs to interface ICs, line receivers, transceivers, and communications semiconductors. Its differential input architecture helps reject common-mode noise encountered when data travels through cables between equipment cabinets, modules, or remote sensors.
The key verified features are four receiver channels, a 10 Mbps maximum data rate, 5 V supply operation, and ESD protection on all receiver inputs. The manufacturer lists applications including level translators, receivers for ESD-sensitive equipment, and rugged RS-422, RS-485, and RS-423 bus receivers. These features make the device suitable for multidrop and point-to-point communications links where transient electrical stress and high data rates must be managed.
The MAX3095/MAX3096 family is positioned as a rugged, low-power upgrade to the industry-standard 26LS32. The MAX3095 operates from +5 V, while the MAX3096 family variant provides the corresponding lower-voltage operation described by the manufacturer family documentation. Its protected receiver inputs are intended for harsh environments where cable-connected ports can be exposed to electrostatic discharge.
Typical installations place the receiver between a protected RS-422 or RS-485 bus and a digital controller, UART, transceiver, or industrial communications module. Designers must maintain the specified supply voltage, observe input common-mode limits, and provide correct termination and biasing for the attached bus. Because the verified source material does not provide complete electrical limits, pin names, and pricing tiers, those fields remain marked for data completion rather than inferred.
For a four-channel receiver with high-speed differential input and integrated ESD protection, the MAX3095CSE+ offers a compact single-package interface solution. This page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes intended to help engineers evaluate the receiver for communications equipment.
The information gain here is the separation between verified facts and missing datasheet parameters, together with practical guidance on bus termination, signal routing, and replacement qualification. Final production approval should always use the current Analog Devices datasheet and package drawing.
Pilihan pengganti yang segera untuk MAX3095CSE+ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX3095CSE+ (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, Supply Voltage, Data Rate, Maximum Data Rate.
MAX3096CSE+
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX3095ESE+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX301ESE
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX3041ESE+T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX3097EESE+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX3095CSE+ Spesifikasi
| Receiver Channels | 4 channels |
| Supported Standards | RS-422 and RS-485 receiver operation |
| Maximum Data Rate | 10 Mbps |
| Tegangan Pemberi Arus | +5 V |
| Input ESD Protection, Human Body Model | ±15 kV |
| Input ESD Protection, Air-Gap Discharge | ±15 kV |
| Input ESD Protection, Contact Discharge | ±8 kV |
| Kemasan | 16-SOIC |
| Jenis Pemasangan | Surface mount |
| Product Type | Quad differential line receiver |
| ESD Protection Location | All receiver inputs |
| Application Category | RS-422/RS-485/RS-423 bus receiver |
| Level Translation | Receiver interface application |
| Telecommunications Suitability | Telecommunications equipment application listed by manufacturer |
Panduan Konfigurasi Pin MAX3095CSE+ 16-soic
Konfigurasi pin untuk MAX3095CSE+ (16-soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MAX3095CSE+.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MAX3095CSE+ patut untuk 6 aplikasis: Industrial RS-485 Control Bus, Telecommunications Equipment Interface, Rugged Data-Link Level Translator, Remote Sensor Network Receiver, Instrumentation and Test Equipment, ESD-Sensitive Communications Equipment.
Industrial RS-485 Control Bus
The MAX3095CSE+ fits an industrial RS-485 receiver input because it provides four differential receiver channels, operation from a 5 V supply, and a verified 10 Mbps data-rate capability. It can receive signals from remote controllers, sensors, actuators, or distributed I/O modules when the bus requires noise-rejecting differential signaling. Place the receiver near the connector, route the pair as a controlled-impedance differential pair, and add the termination and protection components required by the cable length and installation environment. Its input ESD ratings of ±15 kV under the verified Human Body Model and air-gap conditions provide useful input-side ruggedness, although the finished equipment still needs validated surge, ground-fault, and EMC protection.
Disebarkan
Telecommunications Equipment Interface
The MAX3095CSE+ is applicable to telecommunications equipment that receives differential RS-422 or RS-485 signals from remote line cards, backplanes, or service modules. Its four-channel architecture reduces the number of receiver packages required for multi-channel equipment, while the 10 Mbps specification supports high-speed control or data links when the full signal path is designed for that rate. The MAX3095's 5 V supply operation aligns with conventional communications-interface architectures. Keep the receive traces short, maintain a continuous reference plane, and separate the differential pair from switching-power and high-current return paths. The supplied source material lists telecommunications equipment as an application category but does not provide complete timing, common-mode, or temperature limits.
Disebarkan
Rugged Data-Link Level Translator
MAX3095CSE+ can serve as the receive side of a level-translation arrangement between a balanced communications bus and a controller operating at a different logic level. Differential reception helps distinguish the intended signal from common-mode voltage present on long cables, while the protected receiver inputs improve robustness at the board boundary. The four channels allow several independent buses or control lines to enter a system through one package. Because the verified snippets do not specify output thresholds or input common-mode limits, the logic interface must be checked against the controller datasheet before layout release. Use short stub-free routing, suitable grounding, and connector-level protection rather than relying on receiver ESD protection alone.
Disebarkan
Remote Sensor Network Receiver
The MAX3095CSE+ is suitable for receiving differential signals from remote sensor and measurement nodes where cable transients and common-mode noise are concerns. Four receiver channels can support multiple measurement or control links in a compact surface-mount package. The receiver's 10 Mbps capability provides margin for short, well-controlled links, but cable length, baud rate, termination, and topology determine whether the channel will operate reliably. Place the receiver close to the protected connector, use a solid ground reference, and avoid long unprotected stubs. The component's integrated input ESD protection should be considered only one layer of a complete protection strategy and should be coordinated with fuse, resistor, TVS, or isolation components selected for the installation.
Disebarkan
Instrumentation and Test Equipment
The MAX3095CSE+ can be used in instrumentation equipment that accepts external differential command or measurement signals. Its four-channel receiver organization allows multiple instrument interfaces to share a consistent receive architecture, and the 10 Mbps rating supports faster laboratory or industrial-control links when the cable and termination are appropriate. External instruments can present long cables and severe grounding conditions, so designers should verify common-mode range and logic thresholds from the complete datasheet. A practical layout uses connector-side protection, controlled differential routing, and a clean digital return path. Test the complete board for ESD, burst noise, ground shifts, and logic-integrity margins rather than evaluating the receiver package in isolation.
Disebarkan
ESD-Sensitive Communications Equipment
The MAX3095CSE+ is intended for receivers in communications equipment that may be connected to exposed or user-accessible cables. The verified family description specifically lists receivers for ESD-sensitive applications and reports ±15 kV Human Body Model and air-gap protection plus ±8 kV contact protection. These ratings help protect the receiver input when a cable is connected or disconnected, but they do not remove the need for chassis grounding, connector shielding, or appropriately selected external surge protection. Use the receiver as the first protected interface into the board where practical, keep protection parts close to the connector, and validate the arrangement under the applicable product-level ESD test conditions.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX3095CSE+ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX3096CSE+ | MAX3095ESE+ | MAX301ESE | MAX3041ESE+T | MAX3097EESE+ |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | SOIC-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
Penyeberangsung Jelas
- Four-channel receiver integration (vsMAX301ESE)
- Verified 10 Mbps data-rate capability (vsMAX3041ESE+T)
- Input-side ESD protection (vsMAX301ESE)
Catatan Desain
Route each differential receiver input as a short, matched pair with a continuous ground reference and avoid stubs. Place connector-side protection, termination, and optional common-mode components close to the entry point, while keeping the receiver inputs away from switching nodes and high-current return paths. The supplied sources identify ESD-protected inputs and 10 Mbps operation but do not provide a complete recommended PCB layout, so validate the final stackup and impedance against the actual cable and system requirements.
Do not assume that receiver input ESD protection replaces external surge protection or isolation. MAX3095 input ratings are component-level specifications, while field cables can expose the board to larger ground potential differences, conducted transients, and repeated ESD events. Confirm the maximum common-mode input voltage, output timing, and supply limits from the complete datasheet, and test the assembled equipment with its intended connector, cable, grounding, and enclosure.
For a 10 Mbps link, preserve differential pair geometry through connector, protection, termination, and receiver routing. Avoid adding long traces between the protection network and the receiver inputs, and keep return current continuous beneath the pair. Termination and fail-safe biasing must be designed for the actual topology; adding them indiscriminately can reduce signal margin or alter the bus loading. Use oscilloscope measurements with a suitable differential probe or isolated test setup to verify eye opening and common-mode behavior.
Maklumat Kesediaan
The verified manufacturer and distributor snippets do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable unless a separate automotive-qualified ordering variant is verified.