MCP6041-E/MS - 600nA RRIO Op Amp, 14kHz | Microchip
MPN: MCP6041-E/MS ✓ AktifMCP6041-E/MS Ringkasan
An operational amplifier, or op amp, is a high-gain analog building block used in amplification, buffering, filtering, and feedback-control circuits. The MCP6041 belongs to the Microchip MCP6041/2/3/4 family of low-power CMOS operational amplifiers. Its rail-to-rail input stage accepts signals close to either supply rail, while its rail-to-rail output stage provides useful output swing near the supply limits. These characteristics place the device within the amplifier IC and power-management IC hierarchy while supporting portable and low-voltage instrumentation.
The MCP6041-E/MS combines a typical 14 kHz gain-bandwidth product with a typical operating current of 600 nA. Its input offset voltage is specified below 3 mV, and its rail-to-rail input and output behavior reduces the need for additional signal-conditioning stages near the supply rails. Unity-gain stability allows use as a voltage follower without external compensation. The single-amplifier configuration also keeps board area and external interconnection lower than a dual-amplifier package.
Microchip describes the MCP6041 as using advanced CMOS technology with low bias current, high open-loop gain, and rail-to-rail output swing. The relatively low gain-bandwidth product makes it more appropriate for slow sensor signals, current monitoring, and low-frequency filtering than for wideband signal chains. Its low operating current is particularly valuable when the amplifier must remain active continuously in a battery-powered system.
Typical uses include battery-current monitoring, resistive and capacitive sensor conditioning, low-frequency active filters, and buffered transducer interfaces. The device is also suitable for portable instruments where a 1.4 V minimum supply improves compatibility with low-energy system rails. Because its bandwidth is intentionally modest, applications requiring accurate response above the audio or low-frequency sensor range should be reviewed carefully before finalizing the signal path.
For implementation, keep the feedback network short and place input and bypass capacitance close to the device pins. Verify the output-swing limits at the selected supply voltage and load. A unity-gain buffer or modest closed-loop gain is appropriate for the bandwidth available, and larger gains will reduce the usable closed-loop bandwidth in proportion to the noise-gain curve.
This product record combines manufacturer specifications, package information, lifecycle status, ordering variants, and engineering guidance. It also provides application analysis, a same-package replacement comparison, and practical PCB guidance to help engineers evaluate the MCP6041-E/MS before committing it to a low-power analog design.
Pilihan pengganti yang segera untuk MCP6041-E/MS — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MCP6041-E/MS (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Package.
MCP6041-I/MS
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MCP6041T-E/MS
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MCP6041-E/MS Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 14 kHz typical |
| Operating Current | 600 nA typical |
| Maximum Quiescent Current | Less than 1 uA maximum per amplifier |
| Supply Voltage Range | 1.4 V to 6 V |
| Minimum Single Supply Voltage | 1.4 V |
| Input Offset Voltage | Less than 3 mV |
| Input Type | Rail-to-rail input |
| Jenis Output | Rail-to-rail output |
| Slew Rate | 0.003 V/us |
| Unity-Gain Stability | Unity-gain stable |
| Number of Amplifiers | 1 amplifier |
| Kemasan | MSOP-8 |
| Terminal Count | 8 terminals |
| Jenis Pemasangan | Surface mount |
| Operating Temperature Grade | Extended commercial grade |
| Status Lingkungan Hidup | Active |
| Standard Lead Time | 5 weeks |
| Status RoHS | Compliant |
| Lead-Free Status | Lead-free |
| Technology | CMOS |
Konfigurasi Pin MCP6041-E/MS
| Pin 1 | NC — Not connected in the single-amplifier configuration |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | V+ — Positive supply connection |
| Pin 6 | OUT — Analog output |
| Pin 7 | VDD — Positive supply connection |
| Pin 8 | NC — Not connected in the single-amplifier configuration |
Aplikasi Biasa
MCP6041-E/MS patut untuk 6 aplikasis: Battery Current Monitoring, Low-Power Sensor Conditioning, Portable Measurement Instrumentation, Low-Frequency Active Filtering, Portable Audio Signal Buffering, Industrial Threshold Detection.
Battery Current Monitoring
The MCP6041-E/MS fits battery-current monitoring because its 600 nA typical operating current adds very little burden to a long-duration battery-powered system. With a 14 kHz typical gain-bandwidth product, it can amplify a scaled shunt voltage and filter the result without requiring a high-speed amplifier. Rail-to-rail inputs are valuable when the shunt signal occupies much of the available supply range, while rail-to-rail output improves the usable measurement span. Design the shunt and feedback network for the required accuracy, and verify common-mode and output-swing limits at the lowest battery voltage.
Disebarkan
Low-Power Sensor Conditioning
The MCP6041-E/MS is appropriate for conditioning slow resistive, capacitive, or resistive-divider sensor signals when battery life is important. Its 600 nA typical operating current is much lower than that of a conventional general-purpose amplifier, while the 14 kHz typical gain-bandwidth product supports modest closed-loop gains and low-frequency filtering. Rail-to-rail input and output behavior helps preserve signal span in a 1.4 V-to-6 V system. Choose resistor values that control offset, noise, and loading, and keep sensitive input traces short and away from switching nodes.
Disebarkan
Portable Measurement Instrumentation
The MCP6041-E/MS supports portable measurement instruments that combine low standby current with slow analog signal acquisition. Its 600 nA typical operating current and less-than-1-uA maximum quiescent-current specification are useful when multiple analog channels must remain powered for extended periods. The single amplifier can buffer a sensor, amplify a low-frequency signal, or implement an active filter. The 14 kHz gain-bandwidth product is appropriate for measurements spanning DC through low audio-band signals, but it is not intended for high-speed waveform capture. Stable reference grounding and careful decoupling are essential in compact handheld equipment.
Disebarkan
Low-Frequency Active Filtering
The MCP6041-E/MS can implement first-order or low-order active filters for slowly varying signals when low power is more important than bandwidth. Its unity-gain stability simplifies voltage-follower and Sallen-Key-style designs, and the 14 kHz typical gain-bandwidth product provides margin for modest closed-loop gain at low cutoff frequencies. Rail-to-rail output operation is valuable in low-voltage systems because it increases the usable dynamic range of the filter stage. Select resistor and capacitor tolerances according to the required cutoff accuracy, and verify noise, settling, and output-swing behavior in the manufacturer datasheet for the selected topology.
Disebarkan
Portable Audio Signal Buffering
The MCP6041-E/MS can buffer low-level audio or bio-signal paths operating from a low-voltage battery supply. Its rail-to-rail input and output stages maximize signal range, and unity-gain stability permits a direct voltage-follower connection when source impedance is too high for downstream circuitry. The 14 kHz typical gain-bandwidth product is adequate for low-frequency and limited audio-band conditioning rather than high-fidelity wideband amplification. The low 600 nA typical operating current benefits continuously powered accessories, although input bias current, noise, and distortion figures should be checked against the source impedance and required audio bandwidth.
Disebarkan
Industrial Threshold Detection
The MCP6041-E/MS is suitable for slow industrial threshold and limit-detection circuits when the sensing node operates near a low supply rail. Rail-to-rail input capability accepts signals close to the supply boundaries, while the single amplifier can amplify a transducer output and compare it with a reference in a feedback comparator arrangement. The 600 nA typical operating current limits standby consumption, and unity-gain stability avoids additional compensation. For factory equipment, use the industrial-grade MCP6041-I/MS where required, account for offset below 3 mV in threshold accuracy, and isolate the input from motor and relay switching noise.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MCP6041-E/MS — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MCP6041-I/MS | MCP6041T-E/MS |
|---|---|---|---|
| Package | MSOP-8 | MSOP-8 | MSOP-8 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Count | 1 amplifier | 1 amplifier | 1 amplifier |
| Gain-Bandwidth Product | 14 kHz typical | 14 kHz typical | 14 kHz typical |
| Operating Current | 600 nA typical | 600 nA typical | 600 nA typical |
| Supply Voltage Range | 1.4 V to 6 V | 1.4 V to 6 V | 1.4 V to 6 V |
| Input Offset Voltage | Less than 3 mV | Less than 3 mV | Less than 3 mV |
| Input and Output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Unity-Gain Stability | Yes | Yes | Yes |
| Slew Rate | 0.003 V/us | 0.003 V/us | 0.003 V/us |
| Lifecycle Status | Active | Active | Active |
Penyeberangsung Jelas
- Low operating current supports continuously powered portable systems (vsMCP6041-I/MS)
- Identical low-frequency performance in a standard MSOP-8 footprint (vsMCP6041T-E/MS)
- Extended-commercial ordering option supports compact general-purpose analog designs (vsMCP6041-I/MS)
Catatan Desain
Place the MCP6041-E/MS close to the signal source and place its supply-bypass capacitor directly between the VDD and VSS pins. Keep the non-inverting and inverting traces short, particularly for high-impedance sensors, because leakage and stray capacitance can disturb the low-level signals that justify this low-power amplifier. Route the feedback components close to pins 2 and 6, and keep the output away from switching inductors, motor traces, and other high-current paths.
Calculate the amplifier's supply contribution using its actual operating current rather than only the 600 nA typical value. The manufacturer specifies less than 1 uA maximum quiescent current per amplifier, while output current and load transitions add to supply demand. In battery systems, include the quiescent current over the intended standby interval and verify that the supply can start and remain stable across the full battery range. Add local decoupling to isolate low-level measurements from upstream switching ripple.
The 14 kHz typical gain-bandwidth product limits the usable closed-loop bandwidth as gain increases. For a practical approximation, estimate the allowable closed-loop gain from the device's gain-bandwidth product and the required signal bandwidth, then apply design margin. The part is unity-gain stable, so a voltage follower needs no external compensation. Avoid treating it as a general-purpose high-speed amplifier when signal edges, phase margin, or settling time are critical.
Do not assume that rail-to-rail operation produces a perfect 0 V-to-VDD output under every load. Check output-swing and common-mode limits in the manufacturer datasheet for the actual supply voltage and load. Also avoid using the typical offset specification as a guaranteed accuracy limit. For precision threshold sensing, include offset error, resistor tolerance, bias-current effects, and temperature drift in the error budget.
Maklumat Kesediaan
Microchip product information identifies MCP6041-E/MS as RoHS compliant and lead-free. AEC-Q100 qualification, REACH status, halogen-free status, and conflict-minerals status are not stated for this exact ordering code.