MCP6544-I/P - 4-Channel 1.6V R-R Comparator | Microchip
MPN: MCP6544-I/P ✓ AktifMCP6544-I/P Ringkasan
A comparator is an analog integrated circuit that compares an input voltage with a reference voltage and produces a digital logic result indicating whether the input is above or below that threshold. The MCP6544 belongs to the comparator hierarchy within interface and signal-conditioning semiconductors. Its rail-to-rail inputs allow signals to operate close to either supply rail, while its push-pull outputs provide actively driven high and low states without requiring an external pull-up resistor.
The MCP6544 operates from 1.6V to 5.5V and typically consumes 600 nA of quiescent current, with a maximum of 1 microamp. Rail-to-rail input and output operation supports low-voltage systems in which usable signal range and logic compatibility are important. The TTL-compatible outputs and four-channel integration allow one device to implement several independent threshold decisions, reducing component count and board space compared with discrete comparators.
Internally, the MCP6544 combines precision low-power input stages with CMOS output drivers. Because each channel is single-ended and includes the four input pins, one supply pin, one ground pin, and four output pins in the 14-pin PDIP, the device offers straightforward routing in through-hole designs. Its push-pull topology differs from open-drain comparators because the output actively sources current in the high state and sinks current in the low state.
Typical uses include battery monitoring, sensor thresholding, overvoltage and undervoltage detection, digital control interfaces, window comparison in measurement systems, and low-power industrial or portable equipment. Each channel can compare an external analog signal with a locally generated reference or another input voltage. The 5.5V maximum supply also permits operation from common low-voltage rails used by modern embedded systems.
PCB design should prioritize short analog input paths, a stable ground reference, and separation from noisy switching nodes. Input and output traces should avoid running beneath or immediately beside high-current or high-di/dt paths. Because comparator response depends on input slew rate and system layout, the power rails require local bypassing and the analog source impedance should remain low enough to establish the intended threshold accurately.
This product overview combines the MCP6544-I/P electrical characteristics, a 14-pin PDIP pinout reference, application guidance, and a qualified same-family replacement option. It also explains the practical distinction between push-pull and open-drain outputs, low-power threshold applications, and the design conditions required for reliable rail-to-rail comparison.
Pilihan pengganti yang segera untuk MCP6544-I/P — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
MCP6544T-E/P
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MCP6544-I/P Penilaian maksimum & Ciri-ciri Elektrik
| Comparator Type | Quad, single-ended, general-purpose CMOS comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 1.6 V to 5.5 V |
| Typical Quiescent Current | 600 nA |
| Maximum Quiescent Current | 1 uA |
| Input Common-Mode Range | Rail-to-rail |
| Jenis Output | Push-pull, rail-to-rail, TTL-compatible |
| Kemasan | 14-pin PDIP |
| Jenis Pemasangan | Through-hole |
| Automotive Qualification | AEC-Q100 |
| Maximum Supply Voltage | 5.5 V |
| Comparator Family | MCP6544 series |
| Output Pull-Up Requirement | None for push-pull output |
| Industrial Temperature Grade | I-grade variant |
Panduan Konfigurasi Pin MCP6544-I/P 14-pin pdip
Konfigurasi pin untuk MCP6544-I/P (14-pin pdip pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk MCP6544-I/P.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MCP6544-I/P patut untuk 6 aplikasis: Battery Voltage Thresholding, Portable Sensor Conditioning, Industrial Overvoltage Detection, Window Comparison Systems, Automotive Signal Interfacing, Digital Control and System Monitoring.
Battery Voltage Thresholding
The MCP6544-I/P fits battery monitoring because its 1.6V to 5.5V operating range and 600 nA typical quiescent current limit the burden on low-energy systems. Four independent channels can supervise different battery or system rails and generate logic states when each voltage crosses a selected threshold. Rail-to-rail inputs are valuable when the monitored voltage approaches the available supply. The comparator consumes 1 microamp maximum quiescent current, but actual battery life also depends on threshold-switching frequency, output load, and the source impedance of the divider.
Disebarkan
Portable Sensor Conditioning
The MCP6544-I/P can convert slowly varying sensor signals into defined logic states in portable equipment. Its rail-to-rail inputs accommodate signals spanning nearly the full 1.6V to 5.5V supply range, while the push-pull outputs drive digital inputs without an external pull-up. Four channels support independent temperature, pressure, motion, or level thresholds. The design should use a stable reference, low source impedance at the input, and careful grounding because comparator accuracy and response depend on the reference network and input slew rate.
Disebarkan
Industrial Overvoltage Detection
The MCP6544-I/P is suitable for industrial monitoring when low power and rail-to-rail input behavior are priorities. Divider networks can scale several supply or signal voltages into the comparator input range, and the four channels can independently indicate excessive or insufficient voltage conditions. The 1.6V minimum operating voltage supports compact low-voltage control systems, while the 5.5V maximum simplifies compatibility with 5V logic. Protective design still requires input clamping, resistor power ratings, and separation from switching transients.
Disebarkan
Window Comparison Systems
A pair of MCP6544-I/P channels can form an upper and lower threshold window, allowing a system to assert a valid-state signal only when a measured voltage lies between two limits. The quad architecture supports two window comparators in one package when each window uses two channels. Rail-to-rail inputs improve usable signal range, and push-pull outputs simplify interfacing to control logic. Reference tolerances, input offset, propagation delay, and channel-to-channel behavior must be considered when the window limits require high precision.
Disebarkan
Automotive Signal Interfacing
The MCP6544-I/P can perform low-voltage signal qualification in automotive electronic modules because the manufacturer identifies the MCP6544 family with AEC-Q100 offering. Its four channels provide independent decisions for sensor outputs, diagnostic lines, or monitored rails, and the 1.6V to 5.5V range supports low-voltage logic domains. Push-pull outputs eliminate external pull-up components. Vehicle designs must still verify the exact ordering code’s temperature grade, electromagnetic robustness, transient protection, and qualification documentation against system requirements.
Disebarkan
Digital Control and System Monitoring
The MCP6544-I/P can support supervision in embedded control systems by comparing several control voltages against references and presenting the results as push-pull logic signals. Its 600 nA typical quiescent current is favorable for low-power control blocks, and four channels reduce the footprint required for multiple decisions. The active output stage provides predictable high and low drive without a pull-up resistor. Firmware should account for output timing and reference-network tolerances when using comparator events for state transitions or fault handling.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MCP6544-I/P — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MCP6544T-E/P |
|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP |
| Brand | Microchip Technology | Microchip Technology |
| Comparator Configuration | Quad, single-ended | Quad, single-ended |
| Supply Voltage Range | 1.6 V to 5.5 V | 1.6 V to 5.5 V |
| Typical Quiescent Current | 600 nA | 600 nA |
| Maximum Quiescent Current | 1 uA | 1 uA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Type | Push-pull, rail-to-rail, TTL-compatible | Push-pull, rail-to-rail |
| Automotive Qualification | AEC-Q100 | AEC-Q100 family offering |
| Ordering-Code Temperature Class | I-grade | T-E code; exact range differs from I grade |
Penyeberangsung Jelas
- Four independent threshold channels in one through-hole package (vsMCP6544T-E/P)
- Very low quiescent consumption for multi-channel monitoring (vsMCP6544T-E/P)
- Active push-pull outputs simplify downstream logic interfaces (vsMCP6544T-E/P)
Catatan Desain
Route each comparator input directly to its source and reference network with short traces, and keep the analog input nets away from switching nodes, power inductors, and high-current return paths. A comparator can respond to rapid input transitions even when its DC threshold is correct. If the monitored signal crosses the threshold slowly, add filtering at the input, but verify that the added RC network does not create excessive delay or unintended hysteresis.
Do not treat the push-pull output as an open-drain output. The MCP6544 output actively drives both logic states, so adding an external pull-up is normally unnecessary and can increase current during the low state. Conversely, do not substitute an open-drain comparator without checking downstream biasing, bus contention, rise time, and system power requirements. Validate the exact MCP6544 ordering code to preserve the intended package and temperature grade.
Place the device’s supply bypass capacitor close to the supply and ground pins, and use a low-inductance return path to the source of power. Although typical quiescent current is only 600 nA and the maximum is 1 microamp, switching transitions and output loads can create additional supply current. Decoupling helps prevent those events from shifting the reference point or causing an incorrect comparison result. Confirm capacitor voltage rating and stability requirements in the manufacturer documentation.
Use a stable reference with sufficiently low impedance, especially when the comparator input must cross the threshold quickly. Divider resistance should be low enough to avoid excessive input-node charging time but high enough to limit battery drain. Check propagation delay, input offset, and noise performance against the minimum signal transition rate. If the target signal can remain indefinitely close to the threshold, add controlled hysteresis rather than relying on noise-induced switching.
Maklumat Kesediaan
The MCP6544 family is associated with AEC-Q100 offerings. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the cited product and distributor records.