NXP Semiconductors

MKL16Z32VFM4 - 48MHz Cortex-M0+ MCU | NXP Semiconductors

MPN: MKL16Z32VFM4 ✓ Aktif
32-HVQFN (5 mm x 5 mm) Package 48 MHz Speed 32 KB (32K x 8) Memory
MOQ: 1 |

MKL16Z32VFM4 Ringkasan

NXP Semiconductors MKL16Z32VFM4 is a 32-bit Arm Cortex-M0+ Kinetis KL1 microcontroller with a 48 MHz maximum clock, 32 KB of flash memory, 4 KB of SRAM, and a single processing core, housed in a 32-HVQFN package measuring 5 mm by 5 mm. It belongs to the Kinetis KL16 ultra-low-power MCU family and is intended for compact embedded systems requiring efficient processing, analog measurement, communication, and low-power operation.

A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces into one device. The MKL16Z32VFM4 sits within the hierarchy of embedded processor, microcontroller, 32-bit MCU, Arm Cortex-M0+ MCU, and Kinetis KL1 MCU. Its combination of 48 MHz processing performance and 32 KB flash makes it suitable for moderate control workloads without requiring a larger system-on-chip or external memory.

The primary features include an Arm Cortex-M0+ core operating up to 48 MHz, 32 KB of flash, 4 KB of SRAM, and a 5 mm by 5 mm 32-HVQFN package. The low-power orientation of the Kinetis KL1 family supports battery-operated and intermittently powered products. Its compact package also reduces board area, although designers must account for the exposed thermal pad and the fine-pitch land pattern when laying out the PCB.

The MCU architecture combines the Cortex-M0+ instruction set with integrated serial interfaces, timers, and analog functions suited to embedded control. The 32 KB flash provides a constrained but practical code and configuration budget, while 4 KB of SRAM supports stack, data, and peripheral buffering. Firmware development should therefore use the NXP Kinetis KL1 reference manual, device pin data, and the applicable development toolchain rather than assuming resources from a larger Kinetis member.

Typical uses include low-power sensor nodes, compact industrial controls, consumer accessories, battery-powered instruments, and small motor or actuator-control systems. The MCU can also serve as a system controller in designs that combine external sensors, communication transceivers, indicators, and local data acquisition. Peripheral assignments and signal limits must be checked against the device pin table before schematic capture.

For layout, place decoupling capacitors close to the supply pins and provide a continuous ground return beneath the exposed pad. Route high-speed or sensitive analog signals away from switching nodes and programming-interface traces. Firmware configuration, clock selection, low-power modes, and peripheral initialization should follow the NXP reference manual and device errata.

This product page combines the manufacturer specifications with practical guidance for package selection, firmware constraints, application fit, and drop-in replacement evaluation. It also provides structured comparisons for nearby Kinetis KL parts, helping engineers distinguish memory changes from functional compatibility before approving a substitution.

Pilihan pengganti yang segera untuk MKL16Z32VFM4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera MKL16Z32VFM4 (sama faktor bentuk dan kaki) — berbeza dalam Package, Flash Memory, Product Family, SRAM, ADC.

NXP Semiconductors
Package: 32-HVQFN (5x5 mm) with exposed pad
ADC: 12-bit SAR, 8 channels
Bandingkan Dengan MKL16Z32VFM4 →
NXP Semiconductors
Package: 32-HVQFN (5x5 mm)
Product Family: Kinetis L Family, KL0x Series
Bandingkan Dengan MKL16Z32VFM4 →
NXP Semiconductors
Package: 32-HVQFN, 5 mm x 5 mm
Flash Memory: 32 KB
Product Family: Kinetis KL1
Bandingkan Dengan MKL16Z32VFM4 →
NXP Semiconductors
Flash Memory: 64 KB
Product Family: NXP Kinetis KL1 sub-family
Bandingkan Dengan MKL16Z32VFM4 →
NXP Semiconductors
Package: 48-QFN (7x7 mm) with exposed pad
SRAM: 8 KB
ADC: 12-bit SAR, up to 16 single-ended channels
Bandingkan Dengan MKL16Z32VFM4 →

MKL16Z64VFM4

✅ Masuk Drop-In
NXP Semiconductors
📦 32-HVQFN (5 mm x 5 mm)
32-bit ARM Cortex-M0+ microcontroller · NXP Kinetis KL1 sub-family · 48 MHz · 64 KB · 64K x 8 bits · ARM Cortex-M0+ · 32 bits · 1.8 V, 2.5 V, or 3.3 V

Hubungi untuk harga

Lihat Datasheet →

MKL16Z64VFT4R

✅ Masuk Drop-In
NXP Semiconductors
📦 32-HVQFN (5 mm x 5 mm)
ARM Cortex-M0+ (32-bit) · 48 MHz · 64 KB (64K x 8) · 8 KB · 1.71 V to 3.6 V · USB 2.0 Full-Speed Device with on-chip transceiver · Up to 8x36 or 4x40 segments · 12-bit SAR, up to 16 single-ended channels

Hubungi untuk harga

Lihat Datasheet →

MKL15Z32VFM4

✅ Masuk Drop-In
NXP Semiconductors
📦 32-HVQFN (5 mm x 5 mm)
32-bit ARM Cortex-M0+ microcontroller · ARM Cortex-M0+ · 48 MHz · 32-bit · 32 KB · 32K x 8 bit · 4 KB · Kinetis KL1

Hubungi untuk harga

Lihat Datasheet →

MKL02Z32VFM4R

✅ Masuk Drop-In
NXP Semiconductors
📦 32-HVQFN (5 mm x 5 mm)
ARM Cortex-M0+ · 32-bit · 48 MHz · 32 KB (32K x 8) · 4 KB · 1.71 V to 3.6 V · -40C to +105C · 32-HVQFN (5x5 mm) with exposed pad

Hubungi untuk harga

Lihat Datasheet →

MKL16Z32VFM4 Penilaian maksimum & Ciri-ciri Elektrik

Product Type 32-bit ARM Cortex-M0+ microcontroller
Product Series Kinetis KL16
Maximum CPU Frequency 48 MHz
CPU Core Arm Cortex-M0+
Core Count 1 core
Flash Memory 32 KB (32K x 8)
SRAM 4 KB
Architecture 32-bit
Kemasan 32-HVQFN (5 mm x 5 mm)
Jenis Pemasangan Surface mount
Shipping Form Tray
Product Status Active

Panduan Konfigurasi Pin MKL16Z32VFM4 32-hvqfn (5 mm x 5 mm)

Konfigurasi pin untuk MKL16Z32VFM4 (32-hvqfn (5 mm x 5 mm) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.

Garis bentuk pengecah pakai 32-hvqfn (5 mm x 5 mm) untuk MKL16Z32VFM4

Tiada data garisan pin yang diperoleh untuk MKL16Z32VFM4.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MKL16Z32VFM4 patut untuk 6 aplikasis: Battery-Powered Sensor Node, Compact Industrial Control Module, Battery-Powered Handheld Instrument, Consumer Accessory Controller, Small Motor and Actuator Control, Wearable and IoT Sensor Interface.

🧩

Battery-Powered Sensor Node

The MKL16Z32VFM4 fits compact battery-powered sensor nodes that periodically measure an analog condition, process the result, and transmit a short status message. Its 48 MHz Arm Cortex-M0+ core provides responsive control while the Kinetis KL16 family is designed around low-power operation. The 32 KB flash budget supports a compact application program, and 4 KB of SRAM provides space for stack, working variables, and sensor data. Select the appropriate low-power mode, peripheral clock gating, and duty cycle in firmware to control battery consumption.

🏭

Compact Industrial Control Module

The MKL16Z32VFM4 is suitable for compact industrial control modules that coordinate sensors, discrete inputs, status indicators, and a local communications link. Its 48 MHz Cortex-M0+ core is suitable for deterministic supervisory logic, while the Kinetis KL16 family provides communication and analog options beyond the entry-level KL0x class. The 32-HVQFN 5 mm by 5 mm package helps reduce board area in space-constrained controller assemblies. Firmware should reserve sufficient flash for diagnostics and future configuration changes.

📱

Battery-Powered Handheld Instrument

The MKL16Z32VFM4 can serve as the control core of a small handheld measurement instrument that combines a local display, keypad input, sensor interface, and data logging. Its 48 MHz processing rate supports responsive menu and measurement-control logic, while the 32 KB flash and 4 KB SRAM accommodate a focused embedded application. The low-power Kinetis family orientation is valuable for handheld equipment, although battery performance must be evaluated across active, sleep, and shutdown modes. Use low-leakage pull networks and avoid leaving unused digital inputs floating.

🧩

Consumer Accessory Controller

The MKL16Z32VFM4 fits compact consumer accessories that need local control, button handling, status indication, and a low-rate serial connection to a host device. The 48 MHz Cortex-M0+ core provides sufficient performance for protocol handling and responsive user interaction, while 32 KB flash supports a focused application rather than a large graphical application. The 5 mm by 5 mm HVQFN footprint supports dense portable-product layouts. Firmware should use the lowest interrupt latency that meets the user-interface requirement and verify brownout behavior during power transitions.

🔧

Small Motor and Actuator Control

The MKL16Z32VFM4 can coordinate small motors, solenoids, and actuator sequences where the controller needs timers, local interlocks, and compact packaging. Its 48 MHz Cortex-M0+ core can execute timing and state-machine logic, while the Kinetis KL16 family provides the analog and communications resources needed to monitor position or system conditions. The 32 KB flash budget is suitable for a focused motor-control supervisory layer. Exact timer channels, pin assignments, and electrical drive limits must be checked in the device documentation before connecting external loads.

🧩

Wearable and IoT Sensor Interface

The MKL16Z32VFM4 fits IoT and wearable sensor interfaces that translate analog measurements into compact digital data before passing it to a wireless or wired companion device. Its low-power Kinetis family positioning supports intermittent sensing, while the 48 MHz core can service multiple serial peripherals without introducing a larger processor into the design. The 4 KB SRAM limits simultaneous data buffering, so streaming or interrupt-driven processing is usually preferable. Keep sensor traces away from fast digital edges and follow the recommended grounding and decoupling layout.

What are the key specifications of MKL16Z32VFM4 that engineers should know?
The MKL16Z32VFM4 combines a 48 MHz Arm Cortex-M0+ core, 32 KB flash memory, 4 KB SRAM, and one processing core in a 32-HVQFN package measuring 5 mm by 5 mm. According to the NXP product information, it is an active member of the ultra-low-power Kinetis KL16 family. These specifications make it appropriate for compact embedded controllers that need deterministic control, serial connectivity, and economical code storage without the memory demands of a higher-end MCU.
Where can I download the MKL16Z32VFM4 datasheet PDF?
The official MKL16Z32VFM4 datasheet can be accessed through the NXP product page linked on this page. Select the Data Sheet item for the exact 32-HVQFN device and verify the ordering code MKL16Z32VFM4 before using the document. The NXP page also provides the product status, environmental information, shipping information, and related technical resources, which should be checked against the revision and device variant being designed.
Where can I find the MKL16Z32VFM4 pinout and package drawing?
Use the pin descriptions and package drawing in the official NXP data sheet for MKL16Z32VFM4, not a generic 32-pin QFN drawing. The device is specified in a 32-HVQFN 5 mm by 5 mm package, and its exposed pad, numbering sequence, and assigned signal functions must be followed exactly. This page provides the package identity and compatible diagram, while the manufacturer pin table remains the authoritative source for assigning each PCB net.
Is MKL16Z32VFM4 suitable for battery-powered and low-power products?
The MKL16Z32VFM4 is suitable for battery-powered products because it belongs to the Kinetis KL16 ultra-low-power MCU family. Its 48 MHz Cortex-M0+ core provides useful processing performance without requiring a higher-power architecture, while the 32 KB flash and 4 KB SRAM support compact firmware. Actual battery life depends on the selected operating mode, clock configuration, peripheral activity, and duty cycle, so evaluate the power modes in the NXP reference documentation.
What is the difference between MKL16Z32VFM4 and MKL16Z64VFM4?
The primary documented difference is flash capacity: MKL16Z32VFM4 provides 32 KB, while MKL16Z64VFM4 provides 64 KB. Both are identified as 48 MHz Arm Cortex-M0+ Kinetis KL16 devices and use the VFM4 package designation, allowing the 64 KB version to be considered where its larger code and configuration capacity is needed. Firmware, pin functions, peripheral availability, and the exposed-pad connection must still be verified before treating it as a drop-in replacement.
MKL16Z32VFM4 vs MKL16Z64VFM4: which is better for embedded control?
Choose MKL16Z32VFM4 when 32 KB of flash is sufficient and minimizing flash cost or footprint requirements matters. Choose MKL16Z64VFM4 when firmware size, bootloader flexibility, data tables, or future expansion requires twice the flash capacity. Both operate at 48 MHz and use the same VFM4 package family, but the larger-memory device can reduce the risk of exhausting program space during feature expansion.
When should I choose MKL16Z32VFM4 over MKL15Z32VFM4?
Choose MKL16Z32VFM4 when the design requires the Kinetis KL16 feature set rather than the KL15 feature set. The KL16 family provides additional communications and analog peripheral options beyond the KL0x class and is compatible with the broader Kinetis migration path described by NXP. The two devices are not automatically interchangeable at the peripheral and register level, so compare the exact peripheral inventory, pin multiplexing, clock tree, and low-power behavior required by the application.
When should I choose MKL16Z32VFM4 over MKL02Z32VFM4?
Choose MKL16Z32VFM4 when the application needs the broader Kinetis KL1x feature set, including more communications and analog options than the KL0x family. MKL02Z32VFM4 is appropriate when the smaller feature set and 32 KB memory arrangement meet the design requirements. Because a shared memory suffix does not establish register or peripheral equivalence, verify timer, serial-interface, analog, clock, and pin assignments before selecting either device.
What is the best drop-in replacement for MKL16Z32VFM4?
MKL16Z64VFM4 is the closest documented same-package option because it retains the 48 MHz Cortex-M0+ architecture and VFM4 package while increasing flash from 32 KB to 64 KB. It is suitable only when the extra flash and device-specific behavior are acceptable. No cross-manufacturer part can be presented as a verified drop-in replacement without package, pin, memory, peripheral, and software compatibility checks.
Can MKL16Z64VFM4 replace MKL16Z32VFM4 on the same PCB?
MKL16Z64VFM4 can serve as a same-package candidate for MKL16Z32VFM4 because both use the VFM4 package designation and the NXP listings identify the 64 KB version as a 48 MHz Kinetis KL16 Cortex-M0+ MCU. Before installation, confirm that the exposed-pad connection, power pins, communication pins, reset behavior, and firmware assumptions remain compatible. The principal functional change is flash capacity, increasing from 32 KB to 64 KB.
What is the best NXP equivalent for MKL16Z32VFM4?
The closest NXP family alternative is MKL16Z64VFM4 because it combines the same 48 MHz Cortex-M0+ architecture with the same VFM4 package while offering 64 KB of flash instead of 32 KB. It is best considered a memory-expanded candidate rather than a perfect functional clone. MKL15Z32VFM4 and MKL02Z32VFM4 are useful comparison points within the Kinetis portfolio, but their different family feature sets require detailed peripheral review.
Where can I buy MKL16Z32VFM4 online?
Use the Request a Quote form on this page to request MKL16Z32VFM4 availability, current lead time, and order handling. The form is the appropriate channel because stock and commercial terms can change rapidly. Include the exact 32-HVQFN ordering code and required quantity so the quote can be matched to the correct tray or production shipment without ambiguity.
What is the price of MKL16Z32VFM4?
Current pricing for MKL16Z32VFM4 should be requested through the Request a Quote form on this page. The form preserves the exact MPN, package, and requested quantity while allowing the commercial team to confirm current market conditions. Do not treat an archived unit price as a live quotation, since MCU pricing, inventory status, and minimum order quantities can change independently.
What is the lead time and stock status for MKL16Z32VFM4?
Request the current lead time, stock position, and minimum order quantity through the Request a Quote form on this page. NXP lists MKL16Z32VFM4 as active, which indicates an available product family member, but it does not by itself establish the quantity held for a particular order. State your required date and shipment method in the request to obtain an actionable schedule.
What firmware and development tools are recommended for MKL16Z32VFM4?
The recommended workflow is to use the NXP S32 Design Studio or another toolchain capable of targeting the Kinetis KL16 device, together with the S32K configuration and debug support appropriate for the installed hardware. The MKL16Z32VFM4 uses an Arm Cortex-M0+ core, so an Arm-compatible debugger and CMSIS-style programming flow are required. Final peripheral setup, clock settings, and register behavior should follow the exact NXP device documentation and errata.

Data referensi kejuruteraan untuk MKL16Z32VFM4 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose MKL16Z32VFM4 for compact embedded products that need a 48 MHz Arm Cortex-M0+ core, 32 KB flash, 4 KB SRAM, and the broader communications and analog options of the Kinetis KL1x family. Choose MKL16Z64VFM4 when the same package and core are needed but firmware expansion or a larger bootloader is more valuable than minimizing flash capacity. Choose MKL16Z64VFT4 only after confirming its ordering characteristics meet the environmental requirements. Consider MKL15Z32VFM4 for a same-package KL-family comparison when the application needs that family’s peripheral set, and consider MKL02Z32VFM4 for simpler designs that do not require the expanded KL1x resources. For every candidate, verify the pin multiplexing, clock configuration, exposed-pad connection, supply requirements, and firmware support before releasing the PCB.

Perbandingan dengan Gantian

Parametr Produk Ini MKL16Z64VFM4 MKL16Z64VFT4 MKL15Z32VFM4 MKL02Z32VFM4
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 32-HVQFN (5 mm x 5 mm) 32-HVQFN (5 mm x 5 mm) 32-HVQFN (5 mm x 5 mm) 32-HVQFN (5 mm x 5 mm) 32-HVQFN (5 mm x 5 mm)
Product Series Kinetis KL16 Kinetis KL16 Kinetis KL16 Kinetis KL15 Kinetis KL02
Flash Memory 32 KB 64 KB 64 KB 32 KB 32 KB
Communications and Analog Options Expanded Kinetis KL1x options Expanded Kinetis KL1x options Expanded Kinetis KL1x options Different Kinetis family feature set Kinetis KL0x-class feature set

Penyeberangsung Jelas

  • Broader Kinetis KL1x peripheral positioning (vsMKL02Z32VFM4)
  • Direct memory expansion within the KL16 family (vsMKL16Z64VFM4)
  • Same memory capacity with a different family feature set (vsMKL15Z32VFM4)

Catatan Desain

Treat the 32-HVQFN footprint as a fine-pitch assembly job. Follow the NXP land-pattern dimensions, solder-mask and paste-aperture recommendations, and exposed-pad requirements for the exact package. Place the required supply bypass capacitors next to their assigned power pins, provide a solid ground connection to the exposed pad, and route high-current returns away from sensitive analog inputs.

Plan the power tree around the MCU's active and low-power states rather than assuming the 48 MHz clock is always running. Use the device documentation to select the operating mode, clock source, and peripheral gating strategy. Verify brownout behavior, required supply voltage, and decoupling capacitance before schematic release because incorrect rail sequencing or inadequate filtering can cause intermittent debug or communication failures.

Separate analog measurement paths from switching and high-speed digital signals. Keep the Cortex-M0+ debug interface, communication lines, and clock sources away from sensitive inputs, and provide a continuous return path beneath signal routes. Unused inputs should not be left floating. Check pin multiplexing early because valid alternative functions for the same physical pin can change across otherwise similar Kinetis devices.

Do not treat a shared package and memory size as proof of software equivalence. Before substituting a nearby Kinetis part, compare peripheral counts, timer channels, serial interfaces, pin multiplexing, clock-tree behavior, interrupt mapping, and low-power modes. Also confirm the exact exposed-pad connection. MKL16Z64VFM4 is the closest documented candidate, while KL15 and KL02 alternatives require a deliberate firmware and schematic review.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

NXP lists the product as active and provides environmental-quality information, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are stated here.

Data disahkan pada: 2026-11-19 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MKL16Z32VFM4 datasheet MKL16Z32VFM4 pinout MKL16Z32VFM4 datasheet pdf MKL16Z32VFM4 equivalent MKL16Z32VFM4 replacement MKL16Z32VFM4 cross reference MKL16Z32VFM4 vs MKL16Z64VFM4 MKL16Z32VFM4 footprint MKL16Z32VFM4 schematic MKL16Z32VFM4 price MKL16Z32VFM4 stock NXP MKL16Z32VFM4 48MHz Cortex-M0+ 32KB MCU 32-HVQFN Kinetis KL16 MCU MKL16Z32VFM4 low power design

Komponen dan Tanda berkaitan

NXP Semiconductors MKL16Z32VFM4 MKL16Z64VFM4 MKL16Z64VFT4 MKL15Z32VFM4 MKL02Z32VFM4 Arm Cortex-M0+ Kinetis KL16 Kinetis KL1x 32-bit microcontroller embedded processor system-on-chip low-power MCU 32 KB flash memory 4 KB SRAM 48 MHz clock 32-HVQFN package QFN family surface-mount package exposed pad UART SPI I2C ADC S32 Design Studio CMSIS debug interface battery-powered electronics industrial control
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ