OPA363ID - 1.8V, 7MHz RRIO Op Amp | Texas Instruments
MPN: OPA363ID ✓ AktifOPA363ID Ringkasan
A CMOS operational amplifier is a voltage-controlled semiconductor amplifier whose differential input is amplified around a reference point. The OPA363 belongs to the operational-amplifier hierarchy, which sits within analog signal-chain and semiconductor devices. Rail-to-rail input and output capability allows the amplifier to operate close to the positive and negative supply limits, making it useful in low-voltage sensor, filtering, and signal-conditioning circuits where conventional input stages would leave little usable signal range.
The principal features of the OPA363 are its 1.8 V to 5.5 V supply range, 7 MHz gain-bandwidth product, and rail-to-rail input and output operation. Its 90 dB CMRR helps reject common-mode interference, while the common-mode input range includes both supply rails. The output voltage swing is within 10 mV of the relevant supply limit, supporting direct interfacing with low-voltage analog and mixed-signal circuits. An integrated shutdown function provides a way to reduce power use when the signal path is inactive.
The OPA363 and OPA364 families use CMOS input stages and are optimized for very low-voltage, single-supply operation. According to the Texas Instruments OPA363 datasheet, the design avoids the crossover associated with traditional complementary input stages, helping preserve differential linearity and total harmonic distortion when driving analog-to-digital converters. The result is a compact amplifier suitable for precision analog front ends where supply headroom is constrained.
Typical uses include current sensing with a shunt amplifier, sensor-interface conditioning, low-voltage filtering, and ADC driver circuits. The shutdown function is especially useful in battery-powered instrumentation where a sensor or conversion function operates intermittently. The 8-pin SOIC format also supports conventional surface-mount assembly and compact analog boards.
When designing around the OPA363ID, verify the signal amplitude against the rail-to-rail input range, the required closed-loop gain against the 7 MHz gain-bandwidth product, and the output swing at the selected load. Decoupling capacitors should be placed close to the supply pins, and feedback components should be positioned to minimize parasitic capacitance and unstable gain behavior.
This page combines the manufacturer's device description with drop-in family comparisons, parameter-level selection guidance, and practical circuit considerations. It also identifies where application-specific electrical values, lifecycle details, and exact pin descriptions must be confirmed in the manufacturer datasheet before production release.
Pilihan pengganti yang segera untuk OPA363ID — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera OPA363ID (sama faktor bentuk dan kaki) — berbeza dalam Input Common-Mode Range, Output Swing, Package, Technology.
OPA363IDG4
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
OPA363AID
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
OPA364ID
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →OPA364AID
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
OPA363UID
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
OPA363ID Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Single operational amplifier |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Gain-Bandwidth Product | 7 MHz |
| Common-Mode Rejection Ratio | 90 dB |
| Input Common-Mode Range | Includes both negative and positive supply rails |
| Output Swing | Within 10 mV of the supply limit |
| Shutdown Function | Yes |
| Input and Output Type | Rail-to-rail input and output |
| Supply Type | Single supply |
| Technology | CMOS |
| Number of Circuits | 1 circuit |
| Kemasan | 8-pin SOIC |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin OPA363ID 8-pin soic
Konfigurasi pin untuk OPA363ID (8-pin soic pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk OPA363ID.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
OPA363ID patut untuk 6 aplikasis: Battery-Powered Sensor Signal Conditioning, ADC Front-End Amplification, Precision Current-Sense Amplifier, Low-Voltage Active Filtering, Industrial Sensor Interface, Portable Medical Sensor Interface.
Battery-Powered Sensor Signal Conditioning
The OPA363ID fits low-voltage sensor interfaces because it operates from 1.8 V to 5.5 V on a single supply and accepts input signals extending toward both supply rails. A 7 MHz gain-bandwidth product supports moderate closed-loop gains while its 90 dB CMRR helps suppress common-mode noise from nearby digital, switching, or power circuitry. Place the amplifier close to the sensor or conditioning network, and use the shutdown function when periodic readings are not required. The main design trade-off is rail headroom: output swing remains within 10 mV of a supply limit, so large-gain sensor outputs require careful scaling before the amplifier stage.
Disebarkan
ADC Front-End Amplification
OPA363ID can condition low-level analog signals before conversion by an ADC because its rail-to-rail input and output ranges preserve more of the available voltage span at low supply levels. Its 7 MHz gain-bandwidth product provides margin for modest-gain signal paths, and 90 dB CMRR reduces the effect of common-mode voltage at the input. The output swing specification of within 10 mV of the supply limit should be checked against the ADC input range. Decoupling near the amplifier and placement between the source and ADC can reduce noise pickup and preserve signal integrity.
Disebarkan
Precision Current-Sense Amplifier
OPA363ID is appropriate for amplifying the small differential voltage produced by a shunt resistor in a low-voltage current-measurement circuit. Rail-to-rail input operation allows the signal to approach the supply boundaries, while 90 dB CMRR helps reject the common-mode voltage present across a high-current shunt. The 7 MHz gain-bandwidth product is suitable for relatively slow measurement systems and bandwidth-limited filtering. The shunt voltage must be scaled to remain inside the amplifier's input range, and the output must be checked for adequate margin at the maximum measured current.
Disebarkan
Low-Voltage Active Filtering
OPA363ID can implement active filters in compact 1.8 V to 5.5 V analog systems where the signal may approach either supply rail. Its 7 MHz gain-bandwidth product leaves bandwidth for moderate closed-loop gain and compensation, while rail-to-rail output capability improves output range. Component tolerances and amplifier behavior directly affect filter accuracy, so simulation should include the selected resistor and capacitor tolerances. Keep feedback loops compact, connect the bypass capacitor close to the supply pins, and verify phase margin before relying on a high-Q topology.
Disebarkan
Industrial Sensor Interface
OPA363ID supports industrial measurement designs that operate from low-voltage rails and need to amplify sensor outputs without wasting available headroom. The 90 dB CMRR is useful when the sensor is exposed to common-mode industrial noise, and the rail-to-rail input range improves compatibility with low-output sensors. Industrial qualification requirements are not established by the general-purpose ordering code, so environmental and application-specific certification must be reviewed separately. Use stable reference and feedback networks, isolate sensitive input routing from switching nodes, and confirm the operating-temperature requirement against the deployment environment.
Disebarkan
Portable Medical Sensor Interface
OPA363ID can serve as a low-voltage amplifier stage in portable health-monitoring equipment where sensor outputs must be conditioned before digitization. Its 1.8 V minimum supply supports compact battery-powered architectures, and rail-to-rail operation helps retain weak signals near the supply limits. The shutdown function can limit active power when continuous acquisition is unnecessary. Medical-device compliance is determined by the finished system and does not follow automatically from the amplifier ordering code. Signal-chain noise, patient-safety isolation, calibration, and the applicable medical-device standards must therefore be evaluated independently.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk OPA363ID — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | OPA363IDG4 | OPA363AID | OPA364ID | OPA364AID | OPA363UID |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Family | OPA363 | OPA363 | OPA363 | OPA364 | OPA364 | OPA363 |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Shutdown Function | Yes | Yes | Yes | Yes | Yes | Yes |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
Penyeberangsung Jelas
- Supports low-voltage rail-to-rail signal conditioning (vsOPA364ID)
- Provides integrated control for intermittent operation (vsOPA363IDG4)
- Combines 7 MHz bandwidth with 90 dB CMRR (vsOPA364ID)
Catatan Desain
Place the supply-bypass capacitor as close as practical to the OPA363ID positive and ground pins. Keep the input, output, feedback, and reference paths short, and avoid routing sensitive input traces beneath digital, clock, or switching nodes. A compact ground return is particularly important at low supply voltages because trace and via resistance can consume a meaningful portion of the available output range. Follow the manufacturer's layout and evaluation-board guidance when reproducing the recommended circuit.
Do not assume that a rail-to-rail input stage eliminates all headroom limitations. The output remains within 10 mV of the relevant supply limit, so the maximum output voltage must remain below the load or ADC input range under every operating condition. Also check the shutdown logic level against the system supply. Verify gain stability, capacitive-load behavior, and the required operating temperature in the manufacturer datasheet rather than relying only on nominal bandwidth and supply ratings.
The 7 MHz gain-bandwidth product is the principal speed constraint when selecting feedback resistors and capacitors. Calculate the closed-loop bandwidth for the intended noise gain, keep the feedback loop physically small, and add compensation capacitance only where the load and stability analysis supports it. For sensor or ADC interfaces, band-limit the signal appropriately before the amplifier stage so that high-frequency noise does not consume the available bandwidth or degrade transient behavior.
Maklumat Kesediaan
The general-purpose OPA363ID ordering code does not by itself establish RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm the exact device attributes in the current manufacturer product information and the organization's applicable material-compliance documentation.