OPA37GU - 63MHz Ultra-Low-Noise Precision Op Amp | TI
MPN: OPA37GU ✓ AktifOPA37GU Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Precision operational amplifiers add low offset, low bias current, high open-loop gain, and common-mode rejection for instrumentation, audio, sensor, and measurement systems. The OPA37 is a decompensated amplifier, so its stable operating-gain requirement must be considered when selecting feedback values.
Key verified features include 4.5 nV/√Hz maximum input noise at 1 kHz, 100 µV maximum input offset voltage, 0.4 µV/°C offset drift, 117 dB minimum open-loop gain, 100 dB minimum common-mode rejection, and 94 dB minimum power-supply rejection. The supplied product information identifies a ±4 V to ±22 V supply range and a 59 A device-level rating in distributor search data, although the exact application limits should be confirmed against the manufacturer datasheet.
OPA37 family devices use a decompensated architecture intended for higher closed-loop gain than a unity-gain-stable amplifier. The 63 MHz gain-bandwidth product and 11.9 V/µs slew rate support wideband small-signal and precision signal paths, while the low-noise specification is particularly relevant to audio and measurement front ends. Stable feedback-network design remains essential because decompensated amplifiers may require a minimum closed-loop gain.
Typical applications include professional audio equipment, low-noise microphone preamplifiers, instrumentation amplifiers, precision measurement front ends, active filters, and signal-conditioning circuits. The 8-pin SOIC package supports conventional surface-mount PCB assembly, while its low offset and noise help reduce calibration burden when the signal source is close to the input noise floor.
When laying out an OPA37GU circuit, place input, feedback, and decoupling components close to the relevant pins, maintain short ground-return paths, and verify the required minimum closed-loop gain. Use the manufacturer datasheet for complete electrical limits, compensation guidance, common-mode range, output-drive capability, and package drawings. This page combines verified source data with selection and design guidance intended to support engineering comparison rather than replace the datasheet.
Pilihan pengganti yang segera untuk OPA37GU — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera OPA37GU (sama faktor bentuk dan kaki) — berbeza dalam Operating Temperature Range, Manufacturer, Amplifier Type, Number of Circuits, Product Type.
OPA37GU
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →OPA37GP
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →OPA37GU/2K5
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA37GU-2K5G4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA27GU
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →AD510SH
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →AD5174BRMZ-10
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →OPA37GU Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Single decompensated precision operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 63 MHz |
| Slew Rate | 11.9 V/µs |
| Input Noise Density | 4.5 nV/√Hz maximum at 1 kHz |
| Input Offset Voltage | 100 µV maximum |
| Input Offset Voltage Drift | 0.4 µV/°C maximum |
| Open-Loop Gain | 117 dB minimum |
| Common-Mode Rejection | 100 dB minimum |
| Power-Supply Rejection | 94 dB minimum |
| Supply Voltage Range | ±4 V to ±22 V |
| Kemasan | 8-pin SOIC |
| Jenis Pemasangan | Surface Mount |
| Gambaran Suhu Operasi | -40 °C to +85 °C |
Panduan Konfigurasi Pin OPA37GU 8-pin soic
Konfigurasi pin untuk OPA37GU (8-pin soic pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk OPA37GU.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
OPA37GU patut untuk 6 aplikasis: Professional Audio Preamplifier, Precision Instrumentation Front End, Active Audio Filter, Low-Noise Sensor Signal Conditioning, Precision Measurement Amplifier, Precision Voltage Reference Buffer.
Professional Audio Preamplifier
OPA37GU fits low-noise professional audio preamplification because the verified data specifies 4.5 nV/√Hz maximum input noise density at 1 kHz and 11.9 V/µs slew rate. Place it in a closed-loop gain stage with feedback and compensation values selected according to the decompensated OPA37 architecture. The low-noise input stage can improve signal-to-noise ratio for microphone or line-level sources, while the 63 MHz gain-bandwidth product preserves bandwidth for transient-rich audio. Confirm output swing, load impedance, supply headroom, and stability before production; the headline bandwidth does not remove the need for correct gain configuration.
Disebarkan
Precision Instrumentation Front End
OPA37GU is suitable for precision instrumentation when low offset and high rejection improve signal integrity. The verified values include 100 µV maximum input offset voltage, 0.4 µV/°C maximum offset drift, 117 dB minimum open-loop gain, and 100 dB minimum common-mode rejection. Use the amplifier in a gain stage that respects the OPA37 minimum closed-loop gain, with short input traces and a quiet reference or sensor return. The 63 MHz bandwidth provides margin for measurement bandwidth, but designers must still evaluate noise bandwidth, source impedance, input bias current, and common-mode limits with the complete manufacturer datasheet.
Disebarkan
Active Audio Filter
OPA37GU can be used in active filtering where low noise and wideband signal capability are valuable. Its verified 63 MHz gain-bandwidth product and 11.9 V/µs slew rate provide dynamic range for filter stages operating above audio frequencies, while the 4.5 nV/√Hz maximum noise density at 1 kHz helps limit added circuit noise. Because the device is decompensated, choose the closed-loop gain and feedback values required by the OPA37 family rather than copying a unity-gain filter. Simulate component tolerances and verify phase margin, output drive, and supply headroom at the intended load.
Disebarkan
Low-Noise Sensor Signal Conditioning
OPA37GU is appropriate for sensor signal conditioning when the sensor output is small and system noise is important. The verified specifications of 100 µV maximum input offset voltage and 0.4 µV/°C maximum drift help reduce fixed and temperature-related error, while 100 dB minimum common-mode rejection can suppress common-mode disturbances in the measurement path. Use a gain stage above the required decompensated minimum, keep sensor and amplifier grounds short, and control leakage around high-impedance inputs. Verify input bias current and common-mode behavior because those values are not provided in the supplied source data.
Disebarkan
Precision Measurement Amplifier
OPA37GU can serve in precision measurement amplifiers where small differential signals must be amplified while rejecting supply and common-mode disturbances. The verified 117 dB minimum open-loop gain, 94 dB minimum power-supply rejection, and 94 dB-class supply-noise performance support accurate signal recovery, while the 63 MHz bandwidth allows higher-bandwidth instrumentation than a slow precision-only amplifier. The decompensated topology requires deliberate gain selection and stability verification. Keep input and feedback components compact, use low-noise supplies, and confirm output current and settling behavior against the complete manufacturer datasheet.
Disebarkan
Precision Voltage Reference Buffer
OPA37GU can be used to buffer a precision reference when the load requires low added noise and accurate drive. Its 100 µV maximum input offset voltage, 0.4 µV/°C maximum offset drift, 94 dB minimum power-supply rejection, and high open-loop gain are useful for reducing reference-chain error. Configure the amplifier at a closed-loop gain permitted by the OPA37 decompensated architecture and confirm that the output reference current, capacitive loading, and supply range remain within the manufacturer’s limits. The source data does not provide output-current or settling-time values, so those requirements must not be assumed.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk OPA37GU — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | OPA37GU/2K5 | OPA37GU-2K5G4 | OPA27GU | AD510 |
|---|---|---|---|---|---|
| Package | 8-pin SOIC | SOIC-8 family variant | SOIC-8 family variant | SOIC-8 related family variant | SOIC-8 cross-reference candidate |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
Penyeberangsung Jelas
- Verified low-noise performance for precision audio and measurement (vsOPA27GU)
- High-bandwidth decompensated precision architecture (vsAD510)
- Precision DC error specifications (vsAD517)
Catatan Desain
OPA37GU is decompensated, so stability begins with selecting the intended closed-loop gain and a feedback network that satisfies the OPA37 family’s minimum-gain requirement. Do not design it as an unrestricted unity-gain buffer. Check phase margin across the intended noise and signal bandwidth, especially when capacitive loading is present. The verified 63 MHz gain-bandwidth product is a useful bandwidth indicator, but it does not establish stability without the correct topology.
Keep the non-inverting and inverting input paths short, particularly when source impedance is high. Place feedback resistors and compensation-related components close to the amplifier pins, use a continuous low-impedance ground return, and place supply bypass capacitance at the device supply pins. These layout practices reduce parasitic capacitance, leakage, and supply-impedance effects that can degrade a low-noise precision amplifier.
Design the power rails around the verified ±4 V to ±22 V supply range while separately checking absolute maximum limits, common-mode range, output swing, and dissipation in the manufacturer datasheet. A dual-supply notation of ±22 V describes a rail-to-rail span of 44 V, not a 44 V output capability. Use local decoupling and keep the amplifier’s supply current within the package and thermal design limits; those current and thermal figures are not included in the supplied data.
Do not approve a substitute solely because it has the same 8-pin SOIC outline. Confirm exact pin functions, decompensation or minimum-gain behavior, supply range, input common-mode range, noise, offset, bandwidth, slew rate, output drive, and temperature grade. The provided cross-reference material identifies OPA37 family socket candidates but does not supply complete verified electrical data for every candidate, so each substitution requires datasheet review and bench validation.
Maklumat Kesediaan
The supplied verified data does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for OPA37GU. These fields remain unknown rather than being inferred.