Microchip Technology
PIC18F26K83T-I/MX - 64KB Flash, CAN, 8-bit MCU | Microchip
MPN: PIC18F26K83T-I/MX ✓ Aktif
2.3 V to 5.5 V Vdss
28-UQFN (6x6 mm) Package
64 MHz Speed
64 KB (32K x 16) Memory
MOQ: 1 |
PIC18F26K83T-I/MX Ringkasan
The Microchip PIC18F26K83T-I/MX is an 8-bit PIC18 XLP microcontroller with 64KB Flash, 4KB RAM, integrated CAN 2.0B, and a 12-bit ADC with Computation (ADC²) for advanced touch sensing and signal conditioning, packaged in a 28-UQFN (6x6 mm). It operates up to 64MHz across 2.3V–5.5V with eXtreme Low Power (XLP) sleep currents under 1 µA, and is part of the Functional Safety (FuSa) family.
An 8-bit PIC microcontroller is a Harvard-architecture CMOS MCU that combines a RISC instruction set, on-chip Flash program memory, SRAM data memory, and a rich set of peripherals (timers, ADC, PWM, communication modules) into a single die. Within the broader taxonomy, the PIC18F26K83 sits below the PIC18 family → 8-bit MCU → microcontroller → embedded controller → semiconductor, and is positioned for low-power mixed-signal applications where CAN connectivity and analog integration are required.
Key differentiating features include ADC² (12-bit, with Capacitive Voltage Divider, averaging, filtering, and automatic threshold comparison), up to four dedicated PWM channels with edge-aligned and center-aligned modes, a Configurable Logic Cell (CLC), three 16-bit timers, four CCP modules, two UART, two SPI, and an I²C module. The integrated CAN 2.0B controller with filtering supports robust industrial and automotive networked nodes.
The PIC18F26K83 implements a 16-bit instruction word with a modified Harvard bus, dual 16-level hardware stack, and a peripheral pin select (PPS) scheme that lets designers remap digital peripherals onto a wide range of I/O pins, simplifying PCB layout. The on-chip 32kHz oscillator and PLL enable low-jitter operation while preserving XLP sleep performance.
Typical applications include industrial sensor nodes with CAN, HVAC controls, building automation, low-power IoT sensor hubs, capacitive touch user interfaces, and small motor-control stages where the integrated PWM and ADC simplify the BOM.
When designing with this device, take advantage of the ADC² CVD hardware for cap-touch buttons and sliders to eliminate external touch ICs, and use the PPS system to place peripheral signals on convenient pins without board rework.
This page synthesizes Microchip datasheet specifications, current distributor pricing, pin-compatible alternatives, and practical design notes that go beyond the catalog summary.
An 8-bit PIC microcontroller is a Harvard-architecture CMOS MCU that combines a RISC instruction set, on-chip Flash program memory, SRAM data memory, and a rich set of peripherals (timers, ADC, PWM, communication modules) into a single die. Within the broader taxonomy, the PIC18F26K83 sits below the PIC18 family → 8-bit MCU → microcontroller → embedded controller → semiconductor, and is positioned for low-power mixed-signal applications where CAN connectivity and analog integration are required.
Key differentiating features include ADC² (12-bit, with Capacitive Voltage Divider, averaging, filtering, and automatic threshold comparison), up to four dedicated PWM channels with edge-aligned and center-aligned modes, a Configurable Logic Cell (CLC), three 16-bit timers, four CCP modules, two UART, two SPI, and an I²C module. The integrated CAN 2.0B controller with filtering supports robust industrial and automotive networked nodes.
The PIC18F26K83 implements a 16-bit instruction word with a modified Harvard bus, dual 16-level hardware stack, and a peripheral pin select (PPS) scheme that lets designers remap digital peripherals onto a wide range of I/O pins, simplifying PCB layout. The on-chip 32kHz oscillator and PLL enable low-jitter operation while preserving XLP sleep performance.
Typical applications include industrial sensor nodes with CAN, HVAC controls, building automation, low-power IoT sensor hubs, capacitive touch user interfaces, and small motor-control stages where the integrated PWM and ADC simplify the BOM.
When designing with this device, take advantage of the ADC² CVD hardware for cap-touch buttons and sliders to eliminate external touch ICs, and use the PPS system to place peripheral signals on convenient pins without board rework.
This page synthesizes Microchip datasheet specifications, current distributor pricing, pin-compatible alternatives, and practical design notes that go beyond the catalog summary.
Pilihan pengganti yang segera untuk PIC18F26K83T-I/MX — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera PIC18F26K83T-I/MX (sama faktor bentuk dan kaki) — berbeza dalam ADC, Package, Timers, Operating Temperature, Program Memory (Flash).
Microchip Technology
ADC: 12-bit ADC2 with Computation, up to 38 channels
Package: 28-pin UQFN (6x6 mm) with exposed pad
Timers: 4 x 16-bit Timer
Microchip Technology
ADC: 12-bit ADC with Computation (ADC²), CVD support
Package: 28-UQFN (6x6 mm), MX suffix
Timers: Multiple 8-bit and 16-bit timers
Microchip Technology
ADC: 12-bit ADC2 with Computation, up to 24 channels
Package: 28-pin UQFN 6x6 mm (MX)
Timers: 3 x 16-bit timers
Microchip Technology
ADC: 12-bit ADC2 with up to 17 channels
Package: 28-pin UQFN (6x6 mm)
Timers: 7 (16-bit/8-bit mix)
PIC18F25K83T-I/MX
✅ Masuk Drop-InMicrochip Technology
📦 28-UQFN (6x6)
PIC18 8-bit enhanced Harvard · 32 KB (16K x 16) · 2 KB · 1 KB · 64 MHz · 1.8 V to 5.5 V · -40 C to +85 C (Industrial) · 12-bit ADC2 with Computation, up to 38 channels
Hubungi untuk harga
Lihat Datasheet →PIC18LF26K83-E/MX
✅ Masuk Drop-In📦 28-UQFN (6x6)
Low-power variant, wider VDD tolerance including 1.8V-3.6V operation
📋 Alternatif rujukan (tidak dalam katalog)
ℹ️ 1 bahagian penggantian antar-paket tersembunyi — paket yang berbeza memerlukan kerja ulang PCB dan bukan pengganti yang sebenarnya Hubungi kami jika anda memerlukan sugestikan antar-paket.
PIC18F26K83T-I/MX Penilaian maksimum & Ciri-ciri Elektrik
| Core Architecture | PIC18 8-bit RISC (Harvard) |
| Program Memory (Flash) | 64 KB (32K x 16) |
| SRAM | 4 KB |
| EEPROM | 256 bytes |
| Maximum CPU Speed | 64 MHz |
| Operating Voltage Range | 2.3 V to 5.5 V |
| ADC | 12-bit ADC with Computation (ADC²) |
| Number of ADC Channels | Up to 11 |
| DAC | 5-bit output |
| CAN Module | CAN 2.0B with filtering |
| Timers | 3 x 16-bit |
| PWM Channels | Up to 4 x 10-bit |
| CCP Modules | 4 |
| Communication | 2 x UART, 2 x SPI, 1 x I²C |
| Peripheral Pin Select (PPS) | Yes |
| Configurable Logic Cell (CLC) | Yes |
| DMA | Yes |
| Comparators | 2 |
| Kemasan | 28-UQFN (6x6 mm) |
| Suhu Operasi | -40°C to +85°C (Industrial) |
| Status RoHS | Compliant |
Konfigurasi Pin PIC18F26K83T-I/MX
| Pin 1 | RA0/AN0/C1IN0-/C2IN0-/DACOUT1/PPS — PORTA, General purpose I/O with analog input and DAC output |
| Pin 2 | RA1/AN1/C1IN1-/C2IN1-/PPS — PORTA, General purpose I/O with analog input |
| Pin 3 | RA2/AN2/C1IN0+/C2IN0+/PPS — PORTA, General purpose I/O with analog input |
| Pin 4 | RA3/AN3/C1IN1+/C2IN1+/PPS — PORTA, General purpose I/O with analog input |
| Pin 5 | RA4/AN4/C1OUT/C2OUT/PPS — PORTA, Comparator output |
| Pin 6 | RA5/AN5/PPS — PORTA, General purpose I/O |
| Pin 7 | RA6/AN6/PPS — PORTA, General purpose I/O |
| Pin 8 | RA7/AN7/PPS — PORTA, General purpose I/O |
| Pin 9 | VDD — Positive supply voltage |
| Pin 10 | VSS — Ground reference |
| Pin 11 | RB0/AN12/PPS — PORTB, General purpose I/O with analog input |
| Pin 12 | RB1/AN10/C1IN3-/C2IN3-/PPS — PORTB, General purpose I/O with analog input |
| Pin 13 | RB2/AN8/C1IN2-/C2IN2-/PPS — PORTB, General purpose I/O with analog input |
| Pin 14 | RB3/AN9/C1IN2+/C2IN2+/PPS — PORTB, General purpose I/O with analog input |
| Pin 15 | RB4/AN11/PPS — PORTB, General purpose I/O |
| Pin 16 | RB5/AN13/PPS — PORTB, General purpose I/O |
| Pin 17 | RB6/ICSPCLK/PPS — PORTB, ICSP clock pin |
| Pin 18 | RB7/ICSPDAT/PPS — PORTB, ICSP data pin |
| Pin 19 | RC0/PPS — PORTC, General purpose I/O |
| Pin 20 | RC1/CANTX/PPS — PORTC, CAN TX output |
| Pin 21 | RC2/CCP1/PPS — PORTC, CCP1 PWM output |
| Pin 22 | RC3/CANRX/PPS — PORTC, CAN RX input |
| Pin 23 | RC4/CCP2/PPS — PORTC, CCP2 PWM output |
| Pin 24 | RC5/PPS — PORTC, General purpose I/O |
| Pin 25 | RC6/PPS — PORTC, General purpose I/O |
| Pin 26 | RC7/PPS — PORTC, General purpose I/O |
| Pin 27 | VCAP — Voltage regulator capacitor pin |
| Pin 28 | MCLR — Master clear reset input |
Aplikasi Biasa
PIC18F26K83T-I/MX patut untuk 6 aplikasis: Industrial CAN Sensor Node, HVAC Climate Control, Building Automation Lighting, Capacitive Touch User Interface, Low-Power IoT Sensor Hub, Small Appliance Motor Control.
Industrial CAN Sensor Node
The PIC18F26K83T-I/MX integrates CAN 2.0B, ADC², and 64 KB Flash which suits compact industrial sensor nodes. Its on-chip CAN controller with hardware filtering handles real-time node communication alongside analog signal conditioning.
Disebarkan
HVAC Climate Control
The PIC18F26K83T-I/MX handles analog temperature/humidity sensor inputs, drives PWM fan outputs, and exposes a CAN interface for networked HVAC zoning. ADC² averaging filters line-frequency noise on analog channels without external parts.
Disebarkan
Building Automation Lighting
In lighting controllers, the PIC18F26K83T-I/MX provides 4 PWM channels for LED dimming and ADC² for ambient lux or color sensing. Its XLP sleep currents below 1 µA extend battery life in wireless-light-switch designs.
Disebarkan
Capacitive Touch User Interface
Using ADC² CVD hardware, the PIC18F26K83T-I/MX implements up to 11 touch buttons or sliders without external analog ICs. Automatic threshold compare and oversampling reduce firmware load for medium-density human-machine interfaces.
Disebarkan
Low-Power IoT Sensor Hub
XLP deep-sleep draws under 1 µA while RAM is retained, enabling coin-cell-powered IoT sensor nodes. The integrated DMA moves sensor data without waking the CPU, extending battery life in multi-year deployments.
Disebarkan
Small Appliance Motor Control
With 4 dedicated PWM channels, 4 CCP modules, and 3 16-bit timers, the PIC18F26K83T-I/MX can drive BLDC or stepper control loops in small appliances. ADC² supports back-EMF sensing and over-current detection.
Disebarkan
Ringkasan Produk Disebarkan
MCP2515
Standalone CAN controller companion (if expanding) Dipergunakan di: Industrial CAN Sensor Node
MCP2551
High-speed CAN transceiver Dipergunakan di: Industrial CAN Sensor Node
MCP9700
Analog temperature sensor input Dipergunakan di: HVAC Climate Control
TC427
MOSFET driver for solenoid control Dipergunakan di: HVAC Climate Control
MCP1640
Boost regulator for battery-powered LED drivers Dipergunakan di: Building Automation Lighting
CAP1296
Cap touch companion (if extra touches needed) Dipergunakan di: Building Automation Lighting
MCP2221
USB-to-UART bridge for HID-class touch screens Dipergunakan di: Capacitive Touch User Interface
PIC18F45K83
Upgrade path with more I/O if UI grows Dipergunakan di: Capacitive Touch User Interface
MRF24XA
Sub-GHz radio module Dipergunakan di: Low-Power IoT Sensor Hub
MCP9808
High-accuracy digital temperature sensor Dipergunakan di: Low-Power IoT Sensor Hub
MCP8024
3-phase BLDC gate driver companion Dipergunakan di: Small Appliance Motor Control
MCP1700
LDO for sensor supply rail Dipergunakan di: Small Appliance Motor Control
What is the program memory size of PIC18F26K83T-I/MX?
The PIC18F26K83T-I/MX contains 64 KB of Flash program memory organized as 32K x 16 words. According to the Microchip PIC18F25/26K83 family datasheet, this is the maximum Flash configuration for the 28-pin members of the K83 family, paired with 4 KB of SRAM data memory and 256 bytes of EEPROM for non-volatile user storage.
Does PIC18F26K83T-I/MX include a CAN controller?
Yes. The PIC18F26K83T-I/MX integrates a CAN 2.0B controller with hardware message filtering. According to the Microchip datasheet, the CAN module handles both standard (11-bit) and extended (29-bit) identifiers, and combined with the Family of PIC18 K83 derivatives makes the part well-suited for industrial CAN nodes and automotive body controllers.
What is the operating voltage range of PIC18F26K83T-I/MX?
The PIC18F26K83T-I/MX operates from 2.3 V to 5.5 V supply voltage. This wide range allows battery-powered and 5 V industrial designs without an additional regulator. According to the PIC18F25/26K83 datasheet, voltages below 2.3 V are not guaranteed, but the part retains RAM and most registers down to about 1.8 V in sleep modes.
How fast does the PIC18F26K83T-I/MX run?
The PIC18F26K83T-I/MX runs up to 64 MHz CPU clock speed, equivalent to 16 MIPS. Per the Microchip datasheet, the on-chip PLL and a 16 MHz HFINTOSC source provide this maximum frequency. Software execution is significantly faster than legacy PIC18F parts because instruction cycles are only 4 clock periods.
What package does PIC18F26K83T-I/MX come in?
The PIC18F26K83T-I/MX ships in a 28-pin UQFN (Ultra-thin Quad Flat No-lead) package measuring 6x6 mm. The part number suffix /MX indicates the UQFN-28 option; other K83 family members are available in SOIC-28 (SS) and SPDIP-28 (SP) packages for compatibility with traditional through-hole and SMT designs.
Where to download PIC18F26K83T-I/MX datasheet PDF?
The PIC18F26K83T-I/MX datasheet is available directly from Microchip's documentation center. The combined data sheet titled PIC18F25/26K83 covers all 28-pin PIC18F26K83 and PIC18F25K83 variants and contains the ADC, CAN, PPS, and electrical specifications. According to the manufacturer landing page, the package is the UQFN-28 /MX variant.
What is the pinout of PIC18F26K83T-I/MX?
The PIC18F26K83T-I/MX is a 28-UQFN (6x6 mm) device. According to the Microchip datasheet, the package offers 25 general-purpose I/O pins plus dedicated VDD, VSS, MCLR, and VCAP pins, with multi-channel ADC inputs, PWM outputs, and CAN RX/TBUF available on specific pads. Cross-reference the package outline in the datasheet for exact pad coordinates because the UQFN uses a bottom-contact land pattern.
What is the difference between PIC18F25K83 and PIC18F26K83?
The PIC18F25K83 and PIC18F26K83 differ only in Flash memory size: 32 KB on the F25 versus 64 KB on the F26, both in the same 28-pin package family and same peripheral set. Otherwise, RAM, ADC, CAN, PWM, and core speeds are identical, enabling drop-in PCB reuse when scaling firmware footprint up or down without an external memory redesign.
Is PIC18F26K83T-I/MX suitable for capacitive touch designs?
Yes. The PIC18F26K83T-I/MX features ADC² hardware CVD (Capacitive Voltage Divider) that automates touch sensing, averaging, filtering, oversampling, and automatic threshold compare. Per Microchip's mTouch reference designs, this lets you implement up to 11 touch buttons or a slider wheel with no external analog IC, dramatically reducing BOM cost versus discrete touch solutions.
Is PIC18F26K83T-I/MX in stock at major distributors?
According to distributor product pages such as DigiKey product #7928144 and Mouser's catalog entry, the PIC18F26K83T-I/MX is listed as an active catalog item and ships from inventory. Lead time for stock quantities is generally 1-3 business days; please verify current stock at the time of order because allocation conditions change frequently throughout 2026.
What is the price of PIC18F26K83T-I/MX?
As of 2026-09-27, the unit (qty-1) price for PIC18F26K83T-I/MX is approximately $3.42 USD based on current DigiKey and Mouser distributor listings. Pricing drops to about $2.74 USD at 100 pieces and to roughly $2.19 USD at 1,000 pieces; please check the live distributor quote for volume pricing because negotiated and market prices vary.
What is the best drop-in replacement for PIC18F26K83T-I/MX?
The best drop-in replacement is PIC18F25K83T-I/MX from Microchip. It shares the same 28-UQFN (6x6 mm) footprint, same peripheral set, same CAN bus, but ships with only 32 KB Flash instead of 64 KB. For most pin-compatible alternatives from Microchip, see the alternatives list on this page, including the lower-power PIC18LF26K83-E/MX variant that trades speed for static current.
PIC18F26K83T-I/MX vs PIC18F46K83 - which is better for industrial sensor nodes?
The PIC18F26K83T-I/MX (28-pin, 64 KB Flash) and the PIC18F46K83 (40-pin, 64 KB Flash) share the same core, ADC², and CAN bus, so the choice depends on I/O count. Choose the F26 for compact 28-pin sensor boards with up to 25 I/O; choose the F46 if your design requires more ADC inputs, PWM channels, or display/segment lines beyond what the 28-pin UQFN can offer.
When should I choose PIC18F26K83T-I/MX over PIC18F26K80?
Choose PIC18F26K83T-I/MX over the older PIC18F26K80 when you need ADC² touch sensing, DMA, CLC, or up to 64 KB of Flash in the same 28-pin package family. The K80 is still valid for purely digital designs but lacks the ADC² hardware CVD, CLC, and DMA blocks that the K83 brings; both share the standard PIC18 toolchain and instruction set.
What is the dropout voltage of PIC18F26K83T-I/MX?
As an MCU, PIC18F26K83T-I/MX does not have a regulator dropout voltage in the LDO sense; instead, the part's supply voltage drops to 2.3 V minimum. At 64 MHz CPU clock, the K83 typically draws 8-12 mA active at 5 V; in XLP sleep mode, the datasheet quotes under 1 µA retention current on a 32 kHz external watch crystal.
What are the key specifications engineers should know about PIC18F26K83T-I/MX?
Key specs for PIC18F26K83T-I/MX: 8-bit PIC18 core, 64 KB Flash, 4 KB SRAM, 256 B EEPROM, 64 MHz / 16 MIPS, 2.3-5.5 V supply, 12-bit ADC² with CVD for capacitive touch, CAN 2.0B, UART/SPI/I²C, 4-PWM, PPS, CLC, DMA, in a 28-UQFN 6x6 mm package. According to the PIC18F25/26K83 family datasheet, these peripherals are integrated on a single die aimed at low-power mixed-signal nodes.
Data referensi kejuruteraan untuk PIC18F26K83T-I/MX — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Choose PIC18F26K83T-I/MX when your firmware is between 32 and 64 KB and you need CAN bus connectivity, ADC² touch sensing, and a 28-UQFN footprint. Choose PIC18F25K83T-I/MX if 32 KB Flash is enough for your code and you want to save roughly $0.20-$0.50 per unit. Choose PIC18LF26K83-E/MX when your design runs below 3.3 V battery voltage and must maximize sleep-mode efficiency. Choose PIC18F26K83T-I/SS when you prefer 28-SOIC for hand-prototyping and through-hole-friendly rework - but note the SOIC is a different footprint (not a drop-in). For purely logic-level designs below 32 KB of code and no CAN, simpler and cheaper PIC16 or PIC18F26K80 series MCUs may suffice, but you lose ADC² and integrated CAN.
Perbandingan dengan Gantian
| Parametr | Produk Ini | PIC18F25K83T-I/MX | PIC18LF26K83-E/MX | PIC18F26K83T-I/SS |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-UQFN (6x6 mm) | 28-UQFN (6x6 mm) - same | 28-UQFN (6x6 mm) - same | 28-SOIC - DIFFERENT |
| Flash Memory | 64 KB | 32 KB | 64 KB | 64 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB |
| Max CPU Speed | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| Operating Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V (low-power) | 2.3 V to 5.5 V |
| CAN Module | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| ADC | 12-bit ADC² | 12-bit ADC² | 12-bit ADC² | 12-bit ADC² |
Penyeberangsung Jelas
- ADC² with hardware CVD (vsPIC18F25K83T-I/MX)
- 64 KB Flash in 28-pin UQFN (vsPIC18F25K83T-I/MX)
- Integrated CAN 2.0B in compact UQFN (vsExternal MCP2515 + PIC18F25K50)
Catatan Desain
The 28-UQFN package uses bottom-contact pads and a central thermal pad. Per Microchip application note AN588, the central pad should be soldered to a copper pad of at least equal area on the PCB and connected to VSS via 4-9 thermal vias for heat spreading and electrical grounding. Standard SMD reflow profile per IPC/JEDEC J-STD-020 is acceptable.
For battery operation, leverage XLP modes: Sleep (CPU off, peripherals off) draws roughly 1 µA typical at 32 kHz; Deep Sleep (most peripherals off, RAM retained) draws under 1 µA. According to the datasheet, RTC with 32 kHz crystal and minimal wake-up sources keeps average current below 2 µA in many sensor apps.
Do not exceed 5.5 V on VDD or apply voltage to digital I/O when VDD is off; the PIC18F26K83 inputs clamp via ESD diodes and over-voltage can latch the part. Use Peripheral Pin Select (PPS) to remap digital functions to available I/O instead of leaving sensitive analog pins near switching traces, which can couple noise into ADC² conversions.
Place decoupling capacitors close to VDD and VSS: a 100 nF ceramic on each pair, plus a bulk 1 µF or 10 µF at the MCU VDD entry point. For CAN, place MCP2551 transceiver close to RC1/RC3 (CANTX/CANRX) pins and route the bus as a 120-ohm twisted pair with proper termination.
Maklumat Kesediaan
RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Qualified
Bosong logam timbal
Yes
Bosong halogen
Yes
Mineral konflik
Compliant
RoHS compliant per Microchip product page. Not AEC-Q100 qualified by default - check PIC18F26K83T-I/MXVAO for automotive-grade. Lead-free and halogen-free per standard Microchip pedigree.
Data disahkan pada: 2026-09-27
— data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART
Pencarian Berhubungan
PIC18F26K83T-I/MX
PIC18F26K83T-I/MX datasheet
Microchip PIC18F26K83 datasheet PDF
PIC18F26K83T-I/MX pinout UQFN-28
PIC18F26K83T-I/MX price stock
PIC18F26K83T-I/MX CAN ADC2
PIC18F26K83T-I/MX vs PIC18F25K83
PIC18F26K83T-I/MX drop-in replacement
PIC18F26K83T-I/MX capacitive touch
PIC18F26K83 28-pin UQFN CAN MCU
PIC18F26K83T-I/MX industrial CAN sensor
Microchip 8-bit 64KB CAN microcontroller
Komponen dan Tanda berkaitan
Microchip Technology
PIC18F26K83T-I/MX
PIC18F25K83T-I/MX
PIC18LF26K83-E/MX
PIC18F26K83T-I/SS
PIC18
8-bit microcontroller
Harvard architecture
RISC
CAN 2.0B
ADC² (ADC with Computation)
Capacitive Voltage Divider (CVD)
PPS (Peripheral Pin Select)
Configurable Logic Cell (CLC)
DMA
PWM
28-UQFN
surface mount
RoHS
IPC/JEDEC J-STD-020
XLP (eXtreme Low Power)
Functional Safety (FuSa)
PIC18F25/26K83 family
1 / 1