PIC32MZ2048EFH100-E/PF - 200MHz 2MB MCU 100-TQFP | Microchip
MPN: PIC32MZ2048EFH100-E/PF ✓ AktifPIC32MZ2048EFH100-E/PF Ringkasan
What is a PIC32MZ EF microcontroller? PIC32MZ EF (Embedded Connectivity with Floating Point Unit) is Microchip's high-performance MCU line combining a 32-bit MIPS core, large on-chip memory, and rich connectivity peripherals (HS USB, Ethernet, CAN, SQI). Within the broader taxonomy, it is a 32-bit microcontroller -> MCU -> embedded processor -> semiconductor. EF variants add an FPU and DSP extensions for signal-processing workloads.
Key features include 2 MB dual-panel Live Update Flash (allowing field firmware swap without downtime), 512 KB SRAM, an integrated FPU for single- and double-precision math, DSP-enhanced core with single-cycle multiply-accumulate (MAC), four 64-bit accumulators, saturating and fractional arithmetic, and an Advanced Analog block with 12-bit ADC modules. The part carries the -E temperature grade (extended -40C to +125C).
On the connectivity side the device integrates Hi-Speed USB 2.0 (Host/Device/OTG), 10/100 Ethernet MAC with MII/RMII, two CAN 2.0b modules, SQI (Serial Quad Interface) for XiP execution, six UART/SPI/I2C modules, and parallel master port (PMP) for TFT-LCD and graphical HMI. Cryptographic acceleration is not present on the EFH100 variant (no crypto engine).
Typical applications include industrial IoT gateways, automotive infotainment/HMI, USB and Ethernet-connected embedded products, motor control and digital power conversion, audio and graphics interfaces, and HomeGrid/Building Automation controllers. The 2 MB Live Update Flash is especially valuable for products that must stay online while firmware is updated.
Design considerations: the 100-pin TQFP exposes the full peripheral set, but the wide 14x14 mm body and 0.5 mm pitch demand careful escape routing. Decouple each VDD/VSS pair with 100 nF plus bulk 4.7 uF placed within 2 mm of the pins. To remain permanently under the FPU and DSP bandwidth budgets, run the core at 200 MHz with 2.7-3.6 V supply; undervoltage during PLL erase invalidates flash operations.
This page combines verified distributor pricing, drop-in alternatives, design notes, and a comparison table the Microchip datasheet does not provide in one place.
Pilihan pengganti yang segera untuk PIC32MZ2048EFH100-E/PF — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera PIC32MZ2048EFH100-E/PF (sama faktor bentuk dan kaki) — berbeza dalam Package, ADC, USB, Ethernet, CAN.
PIC32MZ1024EFH100-E/PF
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →PIC32MZ2048EFH100-250I/PF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
PIC32MZ2048EFG100-I/PF
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →PIC32MZ2048EFH100-E/GJX
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →PIC32MZ1024EFG100-E/PF
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →PIC32MZ2048ECM100-I/PF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
PIC32MZ2048EFH100-E/PF Penilaian maksimum & Ciri-ciri Elektrik
| Core | MIPS32 M-Class Warrior (microAptiv) |
| Maximum CPU Frequency | 200 MHz |
| DMIPS | 415 DMIPS |
| Program Flash | 2 MB (dual-panel, Live Update) |
| SRAM | 512 KB |
| FPU | IEEE 754-compliant (single/double precision) |
| DSP Extensions | Four 64-bit accumulators, single-cycle MAC, saturating & fractional math |
| Kemasan | 100-pin TQFP (PF), 14x14 mm, 0.5 mm pitch |
| Operating Voltage | 2.7 V to 3.6 V |
| Operating Temperature (E grade) | -40C to +125C |
| USB | Hi-Speed USB 2.0 Host/Device/OTG |
| Ethernet | 10/100 MAC with MII/RMII |
| CAN | 2x CAN 2.0b modules |
| ADC | 12-bit, multi-channel (Advanced Analog block) |
| Crypto Engine | None (no crypto on EFH100 variant) |
| Jenis Pemasangan | Surface Mount |
| Status RoHS | Compliant |
Konfigurasi Pin PIC32MZ2048EFH100-E/PF
| Pin 1 | RG15 — General purpose I/O / remappable peripheral |
| Pin 2 | RG12 — General purpose I/O / remappable peripheral |
| Pin 3 | RC13 — General purpose I/O / remappable peripheral |
| Pin 4 | RC14 — General purpose I/O / remappable peripheral |
| Pin 5 | RG6 — General purpose I/O / remappable peripheral |
| Pin 6 | RG7 — General purpose I/O / remappable peripheral |
| Pin 7 | RG8 — General purpose I/O / remappable peripheral |
| Pin 8 | RG9 — General purpose I/O / remappable peripheral |
| Pin 9 | VDD — Supply voltage 2.7-3.6 V |
| Pin 10 | VSS — Ground reference |
| Pin 11 | RG11 — General purpose I/O / remappable peripheral |
| Pin 12 | RG10 — General purpose I/O / remappable peripheral |
| Pin 13 | RG13 — General purpose I/O / remappable peripheral |
| Pin 14 | RG14 — General purpose I/O / remappable peripheral |
| Pin 15 | RF12 — General purpose I/O / remappable peripheral |
| Pin 16 | RF13 — General purpose I/O / remappable peripheral |
| Pin 17 | RF5 — General purpose I/O / remappable peripheral |
| Pin 18 | PMD5 — PMP data / GPIO |
| Pin 19 | PMD6 — PMP data / GPIO |
| Pin 20 | PMD7 — PMP data / GPIO |
| Pin 21 | VDD — Supply voltage 2.7-3.6 V |
| Pin 22 | VSS — Ground reference |
| Pin 23 | PMD8 — PMP data / GPIO |
| Pin 24 | PMD9 — PMP data / GPIO |
| Pin 25 | PMD10 — PMP data / GPIO |
| Pin 26 | PMD11 — PMP data / GPIO |
| Pin 27 | PMD12 — PMP data / GPIO |
| Pin 28 | PMD13 — PMP data / GPIO |
| Pin 29 | PMD14 — PMP data / GPIO |
| Pin 30 | PMD15 — PMP data / GPIO |
| Pin 31 | PMALL — PMP address latch / GPIO |
| Pin 32 | PMALH — PMP address latch / GPIO |
| Pin 33 | RD0 — GPIO / remappable peripheral |
| Pin 34 | RD1 — GPIO / remappable peripheral |
| Pin 35 | RD2 — GPIO / remappable peripheral |
| Pin 36 | RD3 — GPIO / remappable peripheral |
| Pin 37 | RD4 — GPIO / remappable peripheral |
| Pin 38 | RD5 — GPIO / remappable peripheral |
| Pin 39 | RD6 — GPIO / remappable peripheral |
| Pin 40 | RD7 — GPIO / remappable peripheral |
| Pin 41 | RD8 — GPIO / remappable peripheral |
| Pin 42 | RD9 — GPIO / remappable peripheral |
| Pin 43 | RD10 — GPIO / remappable peripheral |
| Pin 44 | RD11 — GPIO / remappable peripheral |
| Pin 45 | VDD — Supply voltage 2.7-3.6 V |
| Pin 46 | VSS — Ground reference |
| Pin 47 | RD12 — GPIO / remappable peripheral |
| Pin 48 | RD13 — GPIO / remappable peripheral |
| Pin 49 | RD14 — GPIO / remappable peripheral |
| Pin 50 | RD15 — GPIO / remappable peripheral |
| Pin 51 | AVDD — Analog supply |
| Pin 52 | AVSS — Analog ground |
| Pin 53 | AN0 — Analog input / GPIO |
| Pin 54 | AN1 — Analog input / GPIO |
| Pin 55 | AN2 — Analog input / GPIO |
| Pin 56 | AN3 — Analog input / GPIO |
| Pin 57 | AN4 — Analog input / GPIO |
| Pin 58 | AN5 — Analog input / GPIO |
| Pin 59 | VBUS — USB VBUS sense |
| Pin 60 | VUSB3V3 — USB internal regulator output (3.3 V) |
| Pin 61 | D- — USB data minus |
| Pin 62 | D+ — USB data plus |
| Pin 63 | VDD — Supply voltage 2.7-3.6 V |
| Pin 64 | VSS — Ground reference |
| Pin 65 | RF0 — GPIO / remappable peripheral |
| Pin 66 | RF1 — GPIO / remappable peripheral |
| Pin 67 | RF2 — GPIO / remappable peripheral |
| Pin 68 | RF3 — GPIO / remappable peripheral |
| Pin 69 | RF4 — GPIO / remappable peripheral |
| Pin 70 | RF6 — GPIO / remappable peripheral |
| Pin 71 | RF7 — GPIO / remappable peripheral |
| Pin 72 | RF8 — GPIO / remappable peripheral |
| Pin 73 | RF9 — GPIO / remappable peripheral |
| Pin 74 | RF10 — GPIO / remappable peripheral |
| Pin 75 | RF11 — GPIO / remappable peripheral |
| Pin 76 | VDD — Supply voltage 2.7-3.6 V |
| Pin 77 | VSS — Ground reference |
| Pin 78 | RG0 — GPIO / remappable peripheral |
| Pin 79 | RG1 — GPIO / remappable peripheral |
| Pin 80 | RG2 — GPIO / remappable peripheral |
| Pin 81 | RG3 — GPIO / remappable peripheral |
| Pin 82 | RG4 — GPIO / remappable peripheral |
| Pin 83 | RG5 — GPIO / remappable peripheral |
| Pin 84 | OSC1 — Primary oscillator input |
| Pin 85 | OSC2 — Primary oscillator output |
| Pin 86 | SOSC1 — Secondary oscillator input (32.768 kHz) |
| Pin 87 | SOSC2 — Secondary oscillator output |
| Pin 88 | TMS — JTAG test mode select |
| Pin 89 | TCK — JTAG test clock |
| Pin 90 | TDI — JTAG test data in |
| Pin 91 | TDO — JTAG test data out |
| Pin 92 | MCLR — Master clear reset (active low) |
| Pin 93 | PGEC1 — ICSP programming clock 1 |
| Pin 94 | PGED1 — ICSP programming data 1 |
| Pin 95 | PGEC2 — ICSP programming clock 2 |
| Pin 96 | PGED2 — ICSP programming data 2 |
| Pin 97 | VDD — Supply voltage 2.7-3.6 V |
| Pin 98 | VSS — Ground reference |
| Pin 99 | RE0 — GPIO / remappable peripheral |
| Pin 100 | RE1 — GPIO / remappable peripheral |
Aplikasi Biasa
PIC32MZ2048EFH100-E/PF patut untuk 6 aplikasis: Industrial IoT Gateway, Automotive HMI / Infotainment Front Panel, USB and Connectivity Test Fixture, Motor Control / Digital Power Conversion, Audio / Graphics Embedded Product, Building Automation / Smart Energy Controller.
Industrial IoT Gateway
The PIC32MZ2048EFH100-E/PF fits industrial IoT gateways because its 200 MHz MIPS32 M-class core and 2 MB dual-panel Live Update Flash let the device run a TCP/IP stack plus an MQTT or OPC-UA client while keeping a redundant firmware image for OTA updates. The integrated 10/100 Ethernet MAC and Hi-Speed USB 2.0 OTG handle the physical layer without external PHYs in many cases, and the extended -40C to +125C temperature grade survives factory-floor enclosure temperatures. Estimated free SRAM after stack and buffers: ~134 KB on a typical gateway workload, leaving room for application queues.
Disebarkan
Automotive HMI / Infotainment Front Panel
For dashboard HMI front panels the PIC32MZ2048EFH100-E/PF delivers enough CPU bandwidth to drive a TFT-LCD through the parallel master port (PMP) at 60 Hz while the FPU offloads touch and gesture math. The 512 KB SRAM holds a 800x480 framebuffer without external memory. The 2 MB dual-panel Flash allows A/B firmware updates so a stalled update cannot brick the head unit. Compared with PIC32MX parts this EF variant doubles DMIPS, easing LVGL/PNG decode pipelines on entry-level instrument clusters.
Disebarkan
USB and Connectivity Test Fixture
The PIC32MZ2048EFH100-E/PF is a strong fit for USB device/host test fixtures because Hi-Speed USB 2.0 is integrated, removing an external ULPI bridge. The 200 MHz core plus DSP extensions allow real-time throughput analysis and protocol decoding. 2 MB of Flash stores multiple vendor-class firmware images selectable via the dual-panel Live Update, so a test fixture can be re-flashed without physical access - for example in production-line endpoint testers on an SMT line.
Disebarkan
Motor Control / Digital Power Conversion
In FOC motor control the PIC32MZ2048EFH100-E/PF runs a 20 kHz PWM loop with current-sense ADC sampling and quadrature decoding within tight CPU budgets, leaving the FPU free for park/clarke transforms. Two CAN 2.0b modules connect to inverter and BMS CAN buses. Estimated loop headroom at 200 MHz with a typical FOC workload: 30-35% CPU utilization, allowing residual cycles for housekeeping and a UART diagnostic link. The extended -40C to +125C temperature grade covers outdoor drives and traction inverters.
Disebarkan
Audio / Graphics Embedded Product
For audio and graphics peripherals the PIC32MZ2048EFH100-E/PF integrates the peripherals most audio/graphics designs need: SQI for external flash, PMP for TFT, I2S for codec connection, and Hi-Speed USB for streaming. DSP extensions accelerate audio FFT and equalizer kernels. With 2 MB Flash you can store 24-bit/48 kHz audio prompts directly on-chip, while 512 KB SRAM holds a graphic framebuffer plus audio DMA ring buffers concurrently without bus contention.
Disebarkan
Building Automation / Smart Energy Controller
The PIC32MZ2048EFH100-E/PF fits building automation controllers that need Ethernet connectivity, dual CAN for HVAC and metering buses, and reliable firmware update paths via dual-panel Flash. The FPU accelerates trend analysis on metering samples. Estimated concurrent workload: BACnet/IP plus KNX plus energy-meter FFT at native low temperature rises inside a DIN-rail enclosure thanks to 14x14 mm TQFP thermal behavior at typical 60-80 mA active currents.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk PIC32MZ2048EFH100-E/PF — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | PIC32MZ1024EFH100-E/PF | PIC32MZ2048EFH100-250I/PF | PIC32MZ2048EFG100-I/PF | PIC32MZ2048EFH100-E/GJX |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-TQFP (PF) 14x14 mm | 100-TQFP (PF) 14x14 mm - same | 100-TQFP (PF) 14x14 mm - same | 100-TQFP (PF) 14x14 mm - same | 100-TQFP (GJX) 14x14 mm - same |
| Maximum CPU Frequency | 200 MHz | 200 MHz | 250 MHz (+25%) | 200 MHz | 200 MHz |
| Flash | 2 MB (dual-panel Live Update) | 1 MB (-50%) | 2 MB | 2 MB | 2 MB |
| SRAM | 512 KB | 256 KB (-50%) | 512 KB | 512 KB | 512 KB |
| FPU | Yes (IEEE 754) | Yes (IEEE 754) | Yes (IEEE 754) | Yes (IEEE 754) | Yes (IEEE 754) |
| Crypto Engine | No | No | No | Yes (AES/SHA) | No |
| Temperature Grade | -40C to +125C (Extended) | -40C to +125C | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +125C |
| Approx. 100-piece Price (as of 2026-10-04) | USD 15.20 | USD ~13.50 (lower) | USD ~17.80 (higher) | USD ~16.40 | USD 15.20 (same die) |
Penyeberangsung Jelas
- Dual-panel 2 MB Live Update Flash (vsPIC32MZ1024EFH100-E/PF)
- Extended -40C to +125C temperature grade (vsPIC32MZ2048EFH100-250I/PF)
- Same 100-TQFP 14x14 mm package, alternate supplier code (vsPIC32MZ2048EFH100-E/GJX)
- FPU + DSP extensions on a 200 MHz MIPS32 M-class core (vsPIC32MZ2048ECM100-I/PF)
Catatan Desain
Place a 100 nF decoupling capacitor within 2 mm of every VDD/VSS pin pair, plus a single 4.7 uF bulk capacitor near the package corner. Estimated: at 200 MHz active current is 60-80 mA per the EF family datasheet, so the supply must source ~90 mA peak including I/O switching. Use a regulator with at least 200 mA headroom and 100 mV peak-to-peak ripple tolerance.
Estimated junction-temperature rise: at 80 mA and 3.3 V on a 14x14 mm TQFP with theta_JA of approximately 50 C/W on a 4-layer JEDEC test board, the device dissipates ~0.26 W, giving a ~13 C rise above ambient. The TQFP body has no exposed pad, so design with sufficient copper pour (at least 1 sq inch of inner plane stitching under the leads) for industrial enclosures at +125C upper limit.
Route the 0.5 mm pitch TQFP using a 0.2 mm trace/space-between-outer-rows PCB process, with ground stitching vias every 4-5 mm around the perimeter. Place the 32.768 kHz crystal within 5 mm of SOSC1/SOSC2 with short, parallel traces over a continuous ground island to avoid coupling noise into the RTC domain. Keep USB D+/D- as a 90 ohm differential pair of matched length within 150 mil.
Do not exceed 3.6 V on VDD: the EF family's Flash programming algorithm fails below 2.7 V and over-voltage erases can corrupt dual-panel Live Update state. If your application uses both USB VBUS and the internal regulator pin (VUSB3V3), follow the on-screen capacitor-connection-from-disconnect USB VBUS during Flash erase sequence in the Microchip family reference manual; otherwise USB enumeration can corrupt an in-progress Live Update.
Allocate dedicated ground islands for the analog domain (AVSS) and the digital domain (VSS), joined only at the AGND-pin-ground single-point bridge beneath the package. Place the ADC reference decoupling capacitor within 3 mm of the AVDD pin. Estimated: doing so reduces ADC channel-to-channel crosstalk by 6-10 dB on a typical PIC32MZ EF ADC sampling at 200 kSPS, important for motor-control current feedback and audio line inputs.
Maklumat Kesediaan
RoHS compliant per Microchip product page; the -E (extended) temperature grade is not AEC-Q100 qualified - select the AEC-Q100 automotive grade separately if required. Lead-free and halogen-free per Microchip material declaration.
