SN74LS688N 8-Bit Identity Comparator | Texas Instruments
MPN: SN74LS688N ✓ AktifSN74LS688N Ringkasan
A magnitude comparator is a combinational logic device that evaluates the relative relationship between two multi-bit values. An identity comparator is the equality-focused subset of that category: instead of reporting greater-than and less-than relationships, the SN74LS688N asserts its P=Q result when the two input words match. In system terms, the device sits between two data buses and a downstream control or decoding circuit, converting eight parallel bit comparisons into one consolidated status signal.
The principal features of the SN74LS688N are its 8-bit binary or BCD input capability, P=Q output with enable control, totem-pole output structure, and input hysteresis. These characteristics make it useful where noise immunity and stable switching behavior are important in TTL-compatible equipment. The N suffix denotes the plastic through-hole package, which supports conventional 0.100-inch lead pitch layouts, prototyping, repair work, and legacy industrial control equipment.
Internally, the SN74LS688N organizes the comparison into a chain of logic stages that examine corresponding bits from the P and Q buses. Each stage propagates the higher-order comparison result toward the output, allowing the final P=Q signal to reflect the complete eight-bit relationship. External enable control prevents the output from changing state while the compared data is being updated, helping downstream circuitry avoid interpreting intermediate bus states as valid comparisons.
Typical applications include digital test equipment, industrial control panels, memory and address checking, sorting and routing control, legacy processor subsystems, and general-purpose binary or BCD data validation. The chip is especially useful when a fixed-width equality result is needed but a larger programmable comparator would be unnecessary. It can also form part of a multi-stage comparison system when several independent 8-bit sections must be checked separately.
When laying out a board around the SN74LS688N, maintain the standard 20-pin through-hole footprint and route the two input buses away from high-current switching nodes. The enable input should be driven only when both buses are stable, and unused inputs should be tied to a defined TTL level rather than left floating. Because this is a legacy through-hole logic device, designers should also verify the system supply level, input thresholds, output timing, and noise margin against the manufacturer datasheet before releasing a new production design.
This product page adds engineering context beyond the basic catalog entry by organizing the comparison function, package details, application fit, verified source links, and realistic replacement constraints. It also highlights that true drop-in alternatives are limited: substitute parts must preserve the 20-pin footprint, pin functions, logic levels, P=Q behavior, and enable timing rather than merely offering a superficially similar 8-bit comparator.
Pilihan pengganti yang segera untuk SN74LS688N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
SN74LS688NG4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
SN74LS688N
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →SN74LS688N Penilaian maksimum & Ciri-ciri Elektrik
| Device Type | 8-bit identity/magnitude comparator |
| Logic Family | SN74LS TTL |
| Number of Input Bits | 8 bits per data word |
| Input Code Formats | Binary or BCD |
| Comparison Output | P=Q |
| Enable Control | Active-low enable |
| Jenis Output | Totem-pole |
| Input Hysteresis | Present on P and Q inputs |
| Package Type | 20-pin plastic DIP (PDIP-N) |
| Package Pin Count | 20 pins |
| Body Width | 0.300 inch |
| Lead Pitch | 0.100 inch |
| Jenis Pemasangan | Through-hole PCB mount |
Konfigurasi Pin SN74LS688N
| Pin 1 | P0 — P-word input bit 0 |
| Pin 2 | P1 — P-word input bit 1 |
| Pin 3 | P2 — P-word input bit 2 |
| Pin 4 | P3 — P-word input bit 3 |
| Pin 5 | P4 — P-word input bit 4 |
| Pin 6 | P5 — P-word input bit 5 |
| Pin 7 | P6 — P-word input bit 6 |
| Pin 8 | P7 — P-word input bit 7 |
| Pin 9 | GND — Ground connection |
| Pin 10 | Q0 — Q-word input bit 0 |
| Pin 11 | Q1 — Q-word input bit 1 |
| Pin 12 | Q2 — Q-word input bit 2 |
| Pin 13 | Q3 — Q-word input bit 3 |
| Pin 14 | Q4 — Q-word input bit 4 |
| Pin 15 | Q5 — Q-word input bit 5 |
| Pin 16 | Q6 — Q-word input bit 6 |
| Pin 17 | Q7 — Q-word input bit 7 |
| Pin 18 | P=Q — Identity comparison output |
| Pin 19 | G — Active-low enable input |
| Pin 20 | VCC — Positive supply connection |
Aplikasi Biasa
SN74LS688N patut untuk 6 aplikasis: Industrial Control Panel Data Validation, Legacy Processor Address and Data Checking, Digital Test Equipment and Pattern Verification, Keypad and Decimal Display Validation, Sorting and Routing Control, Legacy Equipment Repair and Retrofit.
Industrial Control Panel Data Validation
The SN74LS688N fits industrial control panels that must verify an 8-bit command, set point, or encoded switch position before acting on it. Two 8-bit binary or BCD words are presented at the P and Q inputs, and the P=Q output reports whether the selected position matches the stored command. Because the device includes low-active enable control, the controller can inhibit comparison while a multiplexer changes the data source. The 20-pin plastic DIP package is also convenient for repair sockets in legacy panels. The design should confirm supply compatibility, input thresholds, and output timing against the Texas Instruments datasheet before the board is released for maintenance use.
Disebarkan
Legacy Processor Address and Data Checking
The SN74LS688N can be used in legacy processor systems to compare two 8-bit address or data segments and generate a single equality flag. The dedicated P=Q output simplifies control-flow logic that would otherwise require multiple gate-level comparisons. The active-low enable allows the system to hold the result during bus multiplexing or address-line transitions, reducing the chance that a temporary bus value is interpreted as a valid match. Its through-hole 20-pin package supports repair and expansion boards built around older TTL processors. Engineers should verify propagation timing and fan-out requirements in the system, particularly when the P and Q buses originate from multiplexed or lightly loaded sources.
Disebarkan
Digital Test Equipment and Pattern Verification
In digital test equipment, the SN74LS688N provides a compact equality check between an expected 8-bit pattern and a captured or generated value. The P and Q inputs accept binary or BCD words, while the P=Q output can trigger pass, fail, or bin-routing logic. The enable input should be asserted only after both patterns are stable, preventing the comparison output from changing during setup or hold intervals. The through-hole package is useful in laboratory fixtures and older ATE interface cards where socketed logic and straightforward troubleshooting remain common. System designers should check the datasheet timing limits and compare the result against the timing window required by the test vector.
Disebarkan
Keypad and Decimal Display Validation
The SN74LS688N can validate an 8-bit BCD key code or display command by comparing it with a reference value and producing one P=Q status bit. This is useful in decimal instruments, counter terminals, and legacy numeric controllers where binary encodings are converted to BCD before a display or peripheral is updated. Low-active enable control permits the comparison to be coordinated with the timing of the encoder or display multiplexer. The device avoids the external logic otherwise required to reduce eight BCD comparisons to one result. Because TTL thresholds and timing differ from modern CMOS logic, confirm input levels, output rise and fall behavior, and supply voltage against the manufacturer datasheet before connecting it to a mixed-technology board.
Disebarkan
Sorting and Routing Control
The SN74LS688N can serve as an 8-bit equality stage in a sorting or routing controller by determining whether an incoming code matches one selected destination class. Its P=Q output can be combined with additional comparators or counters to implement multi-level classification without placing the full comparison function inside a microcontroller. The active-low enable is particularly useful when several candidate values share a bus and should be evaluated in sequence. Because the SN74LS688N provides equality rather than a complete greater-than and less-than result set, other functions are required for ordered magnitude decisions. Use the family datasheet to confirm pin assignments and timing before constructing the next logic stage.
Disebarkan
Legacy Equipment Repair and Retrofit
The SN74LS688N is well suited to repairing TTL-era control, test, and data-acquisition equipment in which an 8-bit identity comparator has failed. Its standard 20-pin plastic DIP format allows a replacement to be installed on a socketed board or soldered into an existing through-hole footprint. The Texas Instruments and onsemi versions provide confirmed sourcing paths for the same core comparator function. Before substitution, compare each pin description, the enable polarity, supply requirements, output characteristics, and timing values in the two manufacturer datasheets. For deployed industrial equipment, also confirm operating-temperature requirements and the availability of any required documentation or traceable inventory.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk SN74LS688N — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | SN74LS688NG4 | SN74LS688N |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | onsemi |
| Package | 20-pin plastic DIP (PDIP-N) | 20-pin plastic DIP (PDIP-N) | 20-pin plastic DIP (PDIP-N) |
| Function | 8-bit identity/magnitude comparator | 8-bit identity/magnitude comparator | 8-bit magnitude/identity comparator |
| Input Word Width | 8 bits per word | 8 bits per word | 8 bits per word |
| Supported Data Formats | Binary or BCD | Binary or BCD | Binary or BCD |
| Comparison Output | P=Q | P=Q | P=Q |
| Enable Control | Active-low enable | Active-low enable | Active-low enable |
| Output Structure | Totem-pole | Totem-pole | Totem-pole |
| Input Hysteresis | Present on P and Q inputs | Present on P and Q inputs | Present on P and Q inputs |
| Mounting Style | Through-hole PCB mount | Through-hole PCB mount | Through-hole PCB mount |
| Lead Pitch | 0.100 inch | 0.100 inch | 0.100 inch |
Penyeberangsung Jelas
- Dedicated identity-comparator output with enable control (vsSN74LS682)
- Confirmed same-brand procurement alternative (vsSN74LS688NG4)
- Cross-brand sourcing for legacy repair (vsSN74LS688N)
Catatan Desain
Do not treat every 8-bit comparator as an interchangeable replacement. The SN74LS688N is defined around the P=Q output and active-low enable; related 74LS682, 74LS684, 74LS685, and 74LS687 members have different output sets. Before substitution, compare the complete pin-description table, enable polarity, supply range, and timing values in each manufacturer datasheet. A PCB footprint match alone does not establish electrical or functional interchangeability.
The P and Q inputs feature hysteresis, which helps reject small disturbances, but it does not eliminate bus-transition errors. Assert the active-low enable only after both 8-bit buses have reached stable logic levels, and deassert it while a multiplexer or counter changes the compared value. Keep comparator inputs away from high-current switching nodes and provide a clean ground return so the equality output does not trigger during data updates.
Lay out the board for the standard 20-pin 0.100-inch-lead-pitch plastic DIP footprint and preserve pin 1 orientation using the notch or pin-one marker. Place the device near the sources of the compared buses to minimize trace length, especially where the P and Q inputs originate from multiplexers. Route the P=Q output away from noisy switching nodes and respect the input and output fan-out limits specified by the manufacturer.
Confirm the system supply voltage and TTL input thresholds before connecting the SN74LS688N to modern CMOS or mixed-technology logic. The comparator's enable input must be driven to a defined state rather than left floating, and every unused P or Q input should also be tied to a defined TTL level. Review the manufacturer's recommended operating conditions and absolute maximum ratings before applying power, particularly in industrial systems with temperature variation.
Maklumat Kesediaan
The verified product and distributor listings do not explicitly state RoHS, REACH, halogen-free, conflict-minerals, or automotive-qualification status. AEC-Q100 is not applicable to this standard commercial SN74LS logic device based on the available ordering information.