THS1030IPW - 10-Bit 30-MSPS ADC | Texas Instruments
MPN: THS1030IPW ✓ AktifTHS1030IPW Ringkasan
An ADC is a data-acquisition IC that samples an analog voltage and converts it into a digital code. It belongs to the analog-to-digital converter category, within the broader ADC and DAC family of mixed-signal semiconductors. The THS1030 uses a pipelined conversion architecture, combining a 10-bit output resolution with a maximum sampling rate of 30 MSPS. Its parallel interface transfers each conversion result efficiently to digital logic, a digital signal processor, or a programmable logic device.
Key operating features include a 30 MSPS conversion rate, 10-bit resolution, 3 V to 5.5 V operation, and support for single-ended or differential analog input. The listed maximum power dissipation of 120 mW helps engineers assess thermal loading when the converter operates continuously. The industrial temperature range supports designs deployed in temperature-controlled factory equipment, communications hardware, and test systems rather than only consumer applications.
The converter’s parallel output architecture is important in system design. Instead of using a serial clocked data interface, the THS1030 presents the 10-bit result across dedicated output pins. This can simplify capture into suitable digital logic when the destination device offers a parallel ADC input. Designers must still establish compatible voltage levels, account for conversion timing, and ensure that data-capture logic samples the output at the correct clock edge.
Typical uses include high-speed control-loop monitoring, communications-channel digitization, industrial signal capture, ultrasound-related signal chains, and embedded test equipment. Its 30 MSPS rate provides sufficient throughput for many intermediate-frequency, waveform, and control applications, while the 10-bit result supports general-purpose measurement where very fine quantization is unnecessary.
When laying out the circuit, use short analog traces, a clean ground reference, and decoupling close to the supply pins. Provide the required analog and digital interface connections defined by the manufacturer pin-description table, and confirm acquisition timing across the full 3 V to 5.5 V supply range. Parallel outputs also require careful fan-out and timing analysis when connected to a high-speed controller.
This product page combines the THS1030IPW’s electrical characteristics, package information, application guidance, comparison parameters, and verified drop-in candidates. It also highlights practical design considerations that engineers can apply when planning acquisition timing, routing, decoupling, and replacement decisions.
Pilihan pengganti yang segera untuk THS1030IPW — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera THS1030IPW (sama faktor bentuk dan kaki) — berbeza dalam Architecture, Package, RoHS Status.
THS1030CPWR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
THS1031CPW
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →THS1030IPW Penilaian maksimum & Ciri-ciri Elektrik
| Pemecahkatan | 10 bit |
| Conversion Rate | 30 MSPS |
| Architecture | Pipelined |
| Analog Input Type | Single-ended or differential |
| Number of Analog Inputs | 1 input |
| Digital Output Interface | Parallel |
| Supply Voltage Range | 3 V to 5.5 V |
| Gambaran Suhu Operasi | -40°C to +85°C |
| Temperature Grade | Industrial |
| Maximum Power Dissipation | 120 mW |
| Package Type | 28-TSSOP |
| Package Width | 4.40 mm |
| Number of Terminals | 28 |
| Jenis Pemasangan | Surface mount |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Status RoHS | Compliant |
Panduan Konfigurasi Pin THS1030IPW rectangular
Konfigurasi pin untuk THS1030IPW (rectangular pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk THS1030IPW.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
THS1030IPW patut untuk 6 aplikasis: Industrial Control-Signal Acquisition, Communications Channel Digitization, High-Speed Waveform Capture, Medical and Diagnostic Signal Conditioning, Test and Measurement Equipment, Embedded Data-Acquisition Systems.
Industrial Control-Signal Acquisition
The THS1030IPW fits industrial control and monitoring systems that need faster sampling than a general-purpose low-speed ADC. Its 30 MSPS conversion rate supports dense waveform capture, while the 10-bit output provides sufficient resolution for many position, pressure, and process-control signals. The -40°C to +85°C operating range supports factory equipment exposed to temperature variation. Place the converter close to the sensor or signal-conditioning stage, use short analog routes, and connect its parallel output to logic that can capture the established output timing. The 3 V to 5.5 V operating range supports common industrial supply levels, while the listed 120 mW maximum power dissipation should be considered in compact control assemblies.
Disebarkan
Communications Channel Digitization
The THS1030IPW is suitable for intermediate-frequency and communications-channel digitization where a parallel interface and repeated sampling at 30 MSPS are useful. The converter accepts single-ended or differential analog input, allowing it to work with receiver chains that provide either one signal or a complementary pair. Its 10-bit resolution supports carrier-amplitude and modulation measurements where finer quantization is unnecessary. Keep the analog path short and isolate it from high-speed digital return currents to preserve signal integrity. The 3 V to 5.5 V supply range accommodates common radio and communications hardware, while the industrial temperature rating supports deployed equipment rather than only indoor consumer products.
Disebarkan
High-Speed Waveform Capture
The THS1030IPW can capture repetitive waveforms at up to 30 MSPS, making it appropriate for pulse monitoring, transient characterization, and educational instrumentation. The 10-bit parallel result provides a practical balance between information content and interface complexity for a programmable logic device or digital signal processor. Its one-input architecture keeps the signal path manageable when only one channel must be digitized. Design the capture clock and data-capture logic from the manufacturer timing diagrams so that each 10-bit result is registered at the correct interval. Local supply decoupling and a low-impedance analog reference are important for repeatable measurements, especially when operating continuously within the 120 mW maximum power dissipation.
Disebarkan
Medical and Diagnostic Signal Conditioning
The THS1030IPW can serve as the conversion stage in diagnostic and monitoring equipment when the source bandwidth fits its 30-MSPS sampling capability. Its single-ended or differential input support is useful for accepting either a sensor output or a conditioned complementary signal. The 10-bit resolution is appropriate for supervisory measurements where visualization and trend detection matter more than laboratory-grade quantization. The industrial temperature range supports equipment intended for controlled clinical or industrial environments. Use the manufacturer-recommended decoupling and reference arrangement, preserve short analog traces, and isolate the converter from motors, relay contacts, and switching supplies that could couple noise into the measured signal.
Disebarkan
Test and Measurement Equipment
The THS1030IPW is appropriate for compact oscilloscope, signal-generator feedback, and automated test systems requiring rapid parallel conversion. Its 30 MSPS rate allows the instrument to sample repetitive test-node waveforms, while 10-bit resolution provides useful amplitude detail without requiring a more complex high-resolution converter. The parallel output can connect to acquisition logic when timing and voltage compatibility are designed together. The 3 V to 5.5 V supply range simplifies integration with mixed 3.3 V and 5 V systems. During layout, keep clock and parallel-output traces away from the analog input, use a quiet ground reference, and follow the manufacturer’s component values around the analog interface.
Disebarkan
Embedded Data-Acquisition Systems
The THS1030IPW can act as the high-speed acquisition element in an embedded instrument controlled by an MCU or digital logic device. Its 10-bit parallel output is convenient when the receiving device provides a suitable parallel port, while the one-input configuration supports cost-conscious single-channel designs. The 30 MSPS conversion capability enables repeated sampling of transient events or communication waveforms, and the 3 V to 5.5 V operating range supports common embedded rails. Designers should establish data-ready and clock timing before layout, ensure signal levels remain within the supply rails, and reserve copper for effective decoupling around the 28-TSSOP device.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk THS1030IPW — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | THS1030CPWR | THS1031CPW |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-TSSOP | 28-TSSOP | 28-TSSOP |
| Resolution | 10 bit | 10 bit | 10 bit |
| Conversion Rate | 30 MSPS | 30 MSPS | 30 MSPS |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Temperature Grade | Industrial, -40°C to +85°C | Commercial | Commercial |
| Analog Input Configuration | Single-ended or differential | Single-ended or differential | Single-ended or differential |
| Digital Interface | Parallel | Parallel | Parallel |
Penyeberangsung Jelas
- Industrial temperature capability (vsTHS1030CPWR)
- Established pipelined conversion architecture (vsTHS1031CPW)
- Direct single-ended or differential input support (vsTHS1030CPWR)
Catatan Desain
Route the analog input directly to the converter and keep it away from clock and parallel-data nets. Place the manufacturer-recommended input and bypass capacitors close to their associated pins, use a continuous ground plane, and avoid adding test-probe stubs where signal integrity matters. A differential input arrangement should retain controlled impedance and symmetric routing so common-mode noise is rejected consistently.
Treat the 10-bit parallel outputs as a synchronous high-speed bus. Use the manufacturer timing diagrams to establish setup and hold requirements, account for propagation delay through the controller, and avoid excessive fan-out or long stub branches. Series damping may be required if the connected receiver or board topology produces ringing, but component values and terminations should be selected from measured edge behavior and the established interface timing.
The THS1030IPW operates from 3 V to 5.5 V and has a listed maximum power dissipation of 120 mW. Provide local supply bypassing at the device and keep analog and digital return paths controlled to reduce supply noise. In compact systems, calculate the average dissipation from the actual supply voltage, output switching activity, and load rather than treating the maximum figure as the normal operating condition.
Do not substitute a converter solely because it has the same resolution, sample rate, and package count. Confirm the numbered pin assignments, input range, clock polarity, data timing, output coding, and supply sequencing in the manufacturer documentation. The THS1030CPWR has the same core conversion specifications but a commercial temperature grade, while the THS1031CPW is a different low-power CMOS implementation.
Maklumat Kesediaan
RoHS compliance is identified in the product comparison information. No AEC-Q100 qualification, REACH declaration, lead-free statement, halogen-free statement, or conflict-minerals declaration was established.