TLE6251DS - 1 Mbaud CAN Transceiver | Infineon
MPN: TLE6251DS ✓ AktifTLE6251DS Ringkasan
A CAN transceiver is a physical-layer interface IC that converts logic-level TXD and RXD signals into balanced bus signals and converts received bus states back into a controller-readable signal. Within the hierarchy of interface ICs, CAN transceivers connect digital communication controllers to robust wired networks. They must combine high-speed differential signaling, common-mode rejection, bus fault tolerance, low standby demand, and wake-up capability for dependable vehicle and industrial communication.
Key verified features include operation to 1 Mbaud, compatibility with ISO 11898-2 and ISO 11898-5, a nominal 5 V architecture, and bus wake-up support. The automotive positioning is significant because designers can evaluate the part for vehicle network nodes, but the supplied evidence does not state its exact transceiver count, ESD rating, loop-delay limits, standby current, or junction-temperature limits. Those parameters must be checked in the manufacturer datasheet before final circuit qualification.
The TLE6251DS is intended to sit between a host CAN controller and a two-wire CAN bus. Its TXD input accepts controller signaling, while RXD provides receive-state information to the controller. Differential bus operation reduces sensitivity to common-mode noise relative to a single-ended interface. When bus wake-up is required, a qualified network supervisor, termination network, and supply arrangement must support the transceiver's low-power behavior; exact timing values are unavailable in the verified dataset.
Typical uses include automotive body and powertrain control modules, industrial automation controllers, vehicle gateways, distributed sensors, embedded CAN nodes, and diagnostic equipment. For a new high-speed CAN design, use ISO 11898-2 or ISO 11898-5 as the governing system requirement and verify physical-layer timing against the selected controller. Do not substitute a transceiver solely by SOIC-8 package fit; standby, wake-up, fault behavior, and pin functions must also match.
The principal design check is the complete signal path: controller timing, transceiver propagation delay, bus length and topology, termination, common-mode environment, decoupling, and grounding. Place the device close to the bus connector and controller interface, provide the datasheet-required supply bypassing, and route CANH and CANL as a compact differential pair away from switching nodes.
This page consolidates the verified manufacturer description, distributor specifications, price observation, and cross-reference findings into an engineering-oriented selection record. It also distinguishes verified facts from missing electrical details and identifies replacement candidates that still require manufacturer-based pin and timing validation.
Pilihan pengganti yang segera untuk TLE6251DS — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera TLE6251DS (sama faktor bentuk dan kaki) — berbeza dalam Package, RoHS Status, Mounting Type, Product Type, Supply Voltage Range.
TLE6251G
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TLE6251-2G
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TLE6251DS Spesifikasi
| Product Type | High-speed CAN transceiver |
| Maximum Data Rate | 1 Mbaud |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| CAN Standard Compliance | ISO 11898-2 and ISO 11898-5 |
| Communication Interface | CAN bus |
| Transceiver Mode | Transmit and receive |
| Bus Wake-Up | Supported |
| Standby Feature | Supported |
| Kemasan | PG-DSO-8 |
| Package Family | 8-pin SOIC |
| Jenis Pemasangan | Surface mount |
| Application Environment | Automotive and industrial |
| Operating Temperature Class | Automotive temperature range; exact limits not provided |
Panduan Konfigurasi Pin TLE6251DS 8-pin soic
Konfigurasi pin untuk TLE6251DS (8-pin soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk TLE6251DS.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TLE6251DS patut untuk 6 aplikasis: Automotive Electronic Control Units, Vehicle CAN Gateways, Industrial Automation Controllers, Distributed Sensor Nodes, CAN Diagnostic Equipment, Embedded CAN Communication Modules.
Automotive Electronic Control Units
The TLE6251DS fits an automotive electronic control unit that needs a physical-layer interface for a 5 V CAN network operating up to 1 Mbaud. Position it between the host CAN controller and the CANH/CANL bus so TXD and RXD logic connects directly to the network interface. Its ISO 11898-2 and ISO 11898-5 positioning supports design evaluation for vehicle communication, while bus wake-up can help nodes respond when bus activity is required. Before production use, verify exact temperature ratings, ESD protection, transient immunity, loop timing, and AEC-Q100 documentation.
Disebarkan
Vehicle CAN Gateways
TLE6251DS is appropriate for a vehicle gateway that translates or monitors communication between CAN-connected domains. Its 1 Mbaud capability supports high-speed classic CAN links, while the 4.75 V to 5.25 V supply range aligns with common 5 V controller ecosystems. The bus wake-up feature is useful when a gateway must participate after bus activity, but the system must define standby and sleep behavior carefully. Route the differential pair toward the connector, provide the required supply decoupling, and confirm EMC and transient requirements against the vehicle platform specification.
Disebarkan
Industrial Automation Controllers
The TLE6251DS can serve in industrial automation equipment that connects sensors, actuators, drives, or safety-related control modules to a 1 Mbaud CAN bus. Its ISO 11898-2 and ISO 11898-5 compatibility allows architecture evaluation against the selected physical-layer standard, while differential signaling supports operation in electrically noisy environments. Keep CANH and CANL routed as a pair, observe approved bus topology and termination, and isolate external cables when required. Exact EMC, surge, ground-offset, and fault-recovery characteristics must be verified from the official datasheet.
Disebarkan
Distributed Sensor Nodes
TLE6251DS fits distributed sensor nodes that report measurements through a shared CAN network and must support a 5 V, high-speed physical layer. Place the transceiver next to the node controller and connector to minimize sensitive differential routing, then use the bus wake-up function when remote activation is required. Because many compact sensor assemblies prioritize low standby power, engineers should compare the TLE6251DS standby-current and wake-up timing against system power budgets. Those values are not present in the supplied evidence and must be obtained from the manufacturer datasheet.
Disebarkan
CAN Diagnostic Equipment
TLE6251DS can be evaluated for service interfaces and diagnostic tools that communicate with automotive or industrial nodes at up to 1 Mbaud. The host controller provides CAN framing and diagnostics while the transceiver handles the physical differential bus connection. Bus wake-up may support discovery of sleeping nodes, although tool-specific wake patterns and timing must comply with the network protocol. During development, probe both CANH and CANL relative to ground, verify termination power-off, and confirm that the controller and transceiver timing budget remains within the network specification.
Disebarkan
Embedded CAN Communication Modules
The TLE6251DS is suitable for compact embedded communication modules requiring a conventional high-speed CAN physical layer. Its 8SOIC-class package supports board-space conservation, while the 5 V operating range can simplify integration with compatible controllers. Bus wake-up offers a potential path for low-power module behavior, but firmware must distinguish normal operation, standby, and bus-wake events correctly. Before layout release, verify exact pin functions, exposed-pad requirements, decoupling, termination, and transceiver timing because these details were not included in the verified search excerpts.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TLE6251DS — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TLE6251G | TLE6251-2G |
|---|---|---|---|
| Package | PG-DSO-8 / 8SOIC | 8SOIC | 8SOIC |
| Brand | Infineon | Infineon | Infineon |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver |
| Application Environment | Automotive and industrial | Automotive and industrial | Automotive and industrial |
| Replacement Evidence | Target device | Comparison states terminals and packages are consistent | Comparison page presents a complete-replacement claim |
Penyeberangsung Jelas
- Verified bus wake-up capability (vsTLE6251G)
- Explicit dual standard positioning (vsTLE6251-2G)
- Verified operating data point (vsTLE6251G)
Catatan Desain
Route CANH and CANL as a close, length-matched differential pair and keep the transceiver near the external connector. Avoid splitting the pair around unrelated circuitry, and minimize stub branches because they can degrade signal integrity at the advertised 1 Mbaud rate. Provide the datasheet-required local supply bypassing and establish a low-impedance return path. Exact trace geometry cannot be specified from the supplied excerpts because trace impedance, connector, board stack-up, and EMC limits were not provided.
Do not treat a similarly named CAN transceiver as a drop-in replacement based only on an eight-pin package. Compare TXD and RXD pin functions, logic thresholds, supply range, loop delay, receiver timeout, standby control, wake-up operation, bus-fault behavior, and exposed-pad requirements. The cross-reference evidence for TLE6251G and TLE6251-2G is encouraging but incomplete, so production substitution should follow an official pin-by-pin review and hardware validation rather than distributor equivalence labels.
Design the transceiver on a regulated supply within the verified 4.75 V to 5.25 V range and verify controller and transceiver sequencing before power is applied. Add local high-frequency and bulk decoupling according to the manufacturer layout guidance, then confirm supply ripple and ground bounce during maximum bus activity. Standby and wake-up current were not included in the supplied data, so a low-power mode cannot be approved quantitatively until the official electrical characteristics and application circuit are reviewed.
Maklumat Kesediaan
The verified automotive positioning does not by itself establish AEC-Q100, RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Obtain the current manufacturer declarations and product-change documentation before qualification.