WM8983GEFL/RV - Stereo 24-Bit Audio Codec | Cirrus Logic
MPN: WM8983GEFL/RV ✓ AktifWM8983GEFL/RV Ringkasan
An audio codec is an interface IC that converts analog audio signals into digital data and digital audio data back into analog signals. In a portable multimedia system, the WM8983GEFL/RV can sit between microphones or line-level audio inputs and an I2S or PCM-capable processor. Its speaker-drive capability can then provide an efficient output path for a small speaker or headphone-oriented audio subsystem.
The WM8983GEFL/RV provides 24-bit audio resolution, stereo ADC and DAC channels, I2S and PCM data formats, and a 1 W speaker-driver stage. These features support modern digital audio processors while keeping the external component count relatively low. The 5 mm by 5 mm 32-QFN package also supports compact board layouts, although its exposed thermal pad and fine-pitch footprint require careful PCB layout and assembly planning.
The device is described as a low-power, high-quality stereo codec intended for portable multimedia applications. Its integrated speaker driver reduces the need for a separate output amplifier in suitable low-power designs. Designers should still verify the speaker impedance, output waveform, thermal conditions, and supply configuration against the manufacturer datasheet before establishing a production design.
Typical uses include portable media players, personal audio products, compact consumer electronics, mobile accessories, and embedded multimedia terminals. The I2S interface suits processors with a dedicated digital-audio peripheral, while PCM support offers an additional digital connection format. These interfaces allow captured or generated audio to be transferred digitally without external high-speed converters.
The 32-QFN footprint requires attention to pad layout, exposed-pad soldering, and via placement. Keep analog input, headphone, and speaker outputs away from clock and data routing where practical, and follow the manufacturer’s recommended decoupling and grounding arrangement. Digital interfaces should be driven only when signal levels and timing comply with the device’s electrical limits.
This page consolidates the available interface, resolution, channel-count, package, and speaker-drive information, adds practical application guidance, and identifies the limits of a replacement decision. Pin-level design work should use the manufacturer datasheet pin description and application information rather than inferring connectivity from the package outline.
Pilihan pengganti yang segera untuk WM8983GEFL/RV — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera WM8983GEFL/RV (sama faktor bentuk dan kaki) — berbeza dalam Digital Audio Interface, Package, Product Type.
WM8983GEFL/V
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →WM8983GEFL/RV Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Stereo mobile multimedia audio codec |
| Audio Resolution | 24 bit |
| Digital Audio Interface | I2S and PCM |
| ADC Channels | 2 channels |
| DAC Channels | 2 channels |
| Speaker Driver Output | 1 W |
| Channel Configuration | Stereo |
| Kemasan | 32-QFN, 5 mm x 5 mm |
| Exposed Pad | Present |
| Jenis Pemasangan | Surface mount |
| Power Class | Low-power portable multimedia device |
Panduan Konfigurasi Pin WM8983GEFL/RV 32-qfn, 5 mm x 5 mm
Konfigurasi pin untuk WM8983GEFL/RV (32-qfn, 5 mm x 5 mm pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk WM8983GEFL/RV.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
WM8983GEFL/RV patut untuk 6 aplikasis: Portable Media Player, Mobile Audio Accessory, Digital Voice Recorder, Industrial Voice Panel, Smart Sensor Hub, Compact Gaming Audio Module.
Portable Media Player
The WM8983GEFL/RV fits portable media players that require stereo playback through a small speaker or compact analog output. Its 24-bit ADC and DAC channels support two-channel capture and playback, while I2S or PCM provides a direct digital link to a media processor. The integrated 1 W speaker-driver capability can simplify the output stage when the selected loudspeaker impedance and operating level remain within the datasheet limits. Its 5 mm by 5 mm 32-QFN package also reduces board area compared with separate converter and amplifier components. The design must still account for exposed-pad soldering, thermal conditions, decoupling, and clean grounding around the analog section.
Disebarkan
Mobile Audio Accessory
The WM8983GEFL/RV is suitable for a compact mobile audio accessory requiring high-resolution stereo conversion and a direct speaker-output path. A host processor can exchange 24-bit audio through I2S or PCM, while two ADC channels accept stereo analog input and two DAC channels provide stereo playback. The 1 W speaker driver can eliminate a separate amplifier in designs with limited board area and modest acoustic output requirements. Designers should verify Bluetooth or network-audio latency separately and ensure that the codec's interface timing matches the selected host controller. Thermal and speaker performance must be checked with the final enclosure because both can alter effective output capability.
Disebarkan
Digital Voice Recorder
For a compact digital voice recorder, the WM8983GEFL/RV can provide two 24-bit ADC channels for stereo microphone conditioning and I2S or PCM transfer into a digital signal processor. Its codec architecture allows the host to retain the digital recording and processing chain while the analog capture path is integrated. The low-power portable-device positioning is useful in battery-powered recorders, although the final microphone biasing, input levels, and equivalent input noise must be established from the manufacturer datasheet. The 32-QFN exposed pad should be tied to the recommended ground and thermal layout to prevent local heating from affecting sensitive audio capture.
Disebarkan
Industrial Voice Panel
The WM8983GEFL/RV can serve as the audio conversion and speaker-drive element of a compact industrial voice panel. Two ADC channels support stereo source capture, while I2S or PCM transfers the signal to an embedded controller for filtering, storage, or communication. The 1 W integrated driver is useful for local status prompts or a small panel speaker, provided that acoustic and environmental requirements are conservative. Industrial equipment benefits from the small 5 mm by 5 mm footprint, but designers should isolate clock and digital routing from microphone inputs, verify power-supply noise, and calculate expected thermal rise inside the enclosure before production release.
Disebarkan
Smart Sensor Hub
A smart sensor hub with an audible interface can use the WM8983GEFL/RV to receive stereo audio or system alerts and reproduce them through a small speaker. Its 24-bit conversion and digital I2S or PCM interface allow an embedded host to mix prompts with other sensor data, while the integrated 1 W driver reduces the external component count. The 32-QFN package is practical for compact IoT enclosures, but thermal performance depends on the exposed-pad implementation and copper area. Keep the analog input and speaker return paths controlled by the recommended grounding scheme, particularly when the hub also contains switching power conversion, wireless circuitry, or high-rate sensor interfaces.
Disebarkan
Compact Gaming Audio Module
The WM8983GEFL/RV can form the core of a compact gaming audio module requiring stereo playback, digital interface flexibility, and integrated speaker drive. A game controller, portable console, or accessory processor can provide the 24-bit I2S or PCM stream, while the codec performs analog conversion and drives a small transducer. Using the 1 W output path avoids a separate power amplifier in modest-volume designs, though it is not equivalent to a high-output gaming headset amplifier. The 5 mm by 5 mm 32-QFN footprint supports dense module layouts. Assembly planning must include the exposed-pad paste pattern, via-in-pad policy, and thermal-via arrangement recommended by the manufacturer.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk WM8983GEFL/RV — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | WM8983GEFL/V |
|---|---|---|
| Package | 32-QFN (5 mm x 5 mm) | 32-QFN (5 mm x 5 mm) |
| Brand | Cirrus Logic Inc. | Cirrus Logic Inc. |
| Product Type | Stereo mobile multimedia audio codec | Mobile multimedia codec |
| Audio Resolution | 24 bit | 24 bit |
| Digital Audio Interface | I2S and PCM | I2S and PCM |
| ADC Channels | 2 channels | 2 channels |
| DAC Channels | 2 channels | 2 channels |
| Speaker Driver Output | 1 W | 1 W |
| Channel Configuration | Stereo | Stereo |
Penyeberangsung Jelas
- Combines stereo conversion and speaker drive in one package (vsWM8983GEFL/V)
- Supports both I2S and PCM host interfaces (vsWM8983GEFL/V)
- Compact surface-mount integration (vsWM8983GEFL/V)
Catatan Desain
Design the 32-QFN footprint around the manufacturer land pattern and the exposed-pad connection. Thermal vias under the pad can improve heat transfer, but their diameter, quantity, and tenting must follow the assembly process and datasheet guidance. Place input, output, and bypass capacitors close to their associated pins, while keeping the exposed-pad connection short to the recommended ground or supply plane.
Keep the I2S and PCM clock, data, and control traces away from microphone, line-input, headphone, and speaker outputs. Use a continuous ground reference where practical and avoid routing digital signals beneath sensitive analog nodes. The two ADC channels, two DAC channels, and integrated speaker output require different return-current considerations, so treat analog signal routing and power return paths as separate high-priority layout tasks.
Estimated: with a 1 W speaker-driver output and an assumed 90% power-conversion efficiency, the codec may dissipate about 0.11 W; actual dissipation depends on output waveform, supply voltage, load impedance, and the analog operating mode. Validate this estimate against the manufacturer power data, provide adequate exposed-pad copper and vias, and check junction temperature in the final enclosure rather than treating the nominal 1 W output rating as continuous heat without qualification.
Maklumat Kesediaan
The manufacturer datasheet and product listings do not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this exact order code. AEC-Q100 qualification is not applicable to the documented portable multimedia codec positioning.