AD9632ARZ - 320 MHz High-Speed Op Amp | Analog Devices
MPN: AD9632ARZ ✓ ActiveAD9632ARZ Overview
A high-speed voltage-feedback operational amplifier is a semiconductor amplifier that uses negative feedback to amplify high-frequency signals while maintaining controlled gain, bandwidth, and distortion. In the signal-chain hierarchy, the AD9632ARZ belongs to the operational-amplifier family, which supports analog-to-digital converter drivers, buffer stages, test equipment, communications circuits, and precision signal conditioning. Its voltage-feedback architecture responds rapidly to input changes and supports closed-loop gains of 2 and above.
The principal performance features include a 320 MHz small-signal bandwidth and 250 MHz large-signal bandwidth for a 4 V p-p signal. Slew rate reaches 1500 V/us, allowing large-amplitude signals to transition quickly and limiting distortion in demanding pulse and waveform applications. According to the manufacturer product information, typical spurious-free dynamic range is -113 dBc at 1 MHz and -95 dBc at 5 MHz. These characteristics make the amplifier suitable for systems requiring both high frequency coverage and low signal degradation.
The AD9632ARZ uses a voltage-feedback architecture and is stable at gains of 2 or greater, rather than being optimized for unity-gain operation. Its ±6 V supply capability supports bipolar input and output signal ranges in suitable circuit configurations. The AD9631 and AD9632 share a high-speed, wide-bandwidth family, but the AD9631 is unity-gain stable while the AD9632 requires a minimum closed-loop gain of 2. Correct gain selection is therefore essential when replacing or adapting the amplifier in an existing board.
Typical uses include high-speed ADC input drivers, ultrasound and medical signal-conditioning paths, communications receivers, video and imaging equipment, and laboratory instrumentation. In each case, the amplifier can provide gain and drive capability while its low distortion limits unwanted harmonics. Gain-of-2 operation is appropriate when system stability and maximum bandwidth are more important than unity-gain convenience.
PCB implementation should minimize parasitic capacitance and maintain short feedback paths because excessive trace or component capacitance can reduce stability and alter distortion. Decoupling capacitors should be placed close to the supply pins, and the grounding strategy should provide a low-impedance return for high-frequency current. Confirm output swing, input common-mode range, and thermal conditions against the operating point before production release.
This product guide combines the manufacturer specifications, package information, performance characteristics, application guidance, and design considerations needed to evaluate the AD9632ARZ. It also distinguishes the gain-stability requirements of the AD9632 from related high-speed amplifier options and identifies engineering checks that matter when converting the device into a reliable production design.
Drop-in alternatives for AD9632ARZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with AD9632ARZ (same form factor and footprint) — differing in Large-Signal Bandwidth, Number of Circuits, Package.
No drop-in alternatives available for this product.
Request AlternativesAD9632ARZ Maximum Ratings & Electrical Characteristics
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Small-Signal Bandwidth | 320 MHz |
| Large-Signal Bandwidth | 250 MHz at 4 V p-p |
| Slew Rate | 1500 V/us |
| Minimum Stable Closed-Loop Gain | 2 V/V |
| Typical SFDR at 1 MHz | -113 dBc |
| Typical SFDR at 5 MHz | -95 dBc |
| Supply Voltage | ±6 V |
| Package | 8-SOIC, 3.90 mm body width |
| Mounting Type | Surface mount |
| Packaging | Tube |
| Production Status | Production |
AD9632ARZ 8-soic, 3.90 mm body width Pin Configuration Guide
Pin configuration for AD9632ARZ (8-soic, 3.90 mm body width package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for AD9632ARZ.
Refer to the datasheet for full pin configuration.
Typical Applications
AD9632ARZ is suitable for 6 applications: High-Speed ADC Input Driver, Communications Receiver Signal Conditioning, Ultrasound and Medical Signal Conditioning, Video and Imaging Amplification, Test and Measurement Instrumentation, Industrial Sensor Signal Conditioning.
High-Speed ADC Input Driver
The AD9632ARZ fits ADC front ends that require a low-distortion buffer or gain stage before conversion. Its 320 MHz small-signal bandwidth, 250 MHz large-signal bandwidth at 4 V p-p, and 1500 V/us slew rate allow rapid transitions to pass through the signal chain. The device is stable at a minimum gain of 2, so the feedback network can use the amplifier's high-speed operating region while rejecting converter switching energy. During design, verify the ADC input capacitance, output-voltage swing, and required settling accuracy, then place the feedback components close to the amplifier to minimize parasitic feedback. The ±6 V supply capability supports bipolar drive conditions when paired with suitable input and output swing.
Recommended
Communications Receiver Signal Conditioning
The AD9632ARZ is appropriate for communications receivers that need low-distortion amplification of high-frequency waveforms. Its 320 MHz small-signal bandwidth covers a broad range of IF and baseband signal-conditioning needs, while the 1500 V/us slew rate helps preserve edge quality on large-amplitude transitions. Typical SFDR of -113 dBc at 1 MHz and -95 dBc at 5 MHz supports applications where harmonics or intermodulation products would otherwise limit receiver performance. The amplifier must be used at a closed-loop gain of 2 or greater. PCB implementation should use short feedback routes, controlled return paths, and close decoupling because parasitic inductance and capacitance can change both stability and distortion at these frequencies.
Recommended
Ultrasound and Medical Signal Conditioning
The AD9632ARZ can amplify the short, high-frequency pulses used in ultrasonic and medical acquisition systems. Its 320 MHz bandwidth supports wideband signal paths, and the 1500 V/us slew rate helps the amplifier reproduce steep pulse edges without excessive slew distortion. The -113 dBc typical SFDR at 1 MHz is particularly useful when reducing harmonic content in sensitive front ends. Because the AD9632 is stable only at gain 2 or greater, designers should confirm that the transducer, protection network, and amplifier feedback establish a valid noise gain. Input protection, patient-isolation requirements, and medical regulatory obligations must be handled by the complete system rather than by the amplifier alone.
Recommended
Video and Imaging Amplification
The AD9632ARZ can serve as a high-speed gain or drive stage in imaging systems that process analog video or high-rate sensor outputs. Its 320 MHz small-signal bandwidth and 250 MHz large-signal bandwidth provide margin for wideband components, while the 1500 V/us slew rate supports fast transitions at higher amplitudes. Low-distortion behavior helps retain signal fidelity when the output is routed into an ADC, display driver, or subsequent analog stage. The minimum stable gain of 2 must be incorporated into the amplifier topology from the first schematic stage. Keep the feedback loop compact, use a controlled ground reference, and verify the output swing against the sensor and converter limits to avoid clipping before the available headroom is reached.
Recommended
Test and Measurement Instrumentation
The AD9632ARZ is well suited to precision test and measurement front ends where source signals must be amplified with limited distortion. The 320 MHz small-signal bandwidth supports high-frequency probes and buffers, while 1500 V/us slew rate improves large-signal fidelity. For sinusoidal and multitone measurements, the manufacturer's typical SFDR figures of -113 dBc at 1 MHz and -95 dBc at 5 MHz provide a useful starting point for harmonic budgeting. The amplifier's gain-of-2 stability requirement simplifies selection for many non-inverting signal-conditioning paths. Use short connections between the source, amplifier, and converter, maintain symmetric return paths, and account for probe and fixture capacitance. Calibration should be performed with the final input network and cable loading because external parasitics can alter the observed response.
Recommended
Industrial Sensor Signal Conditioning
The AD9632ARZ can amplify outputs from fast industrial sensors when the signal path requires more bandwidth than a general-purpose amplifier can provide. Its 320 MHz small-signal bandwidth and 1500 V/us slew rate are useful for sensors that produce rapidly changing waveforms, while the low-distortion characteristics help preserve useful signal content. The part operates from ±6 V and is stable at gain 2 or greater, allowing a straightforward non-inverting conditioning topology when the sensor requires additional amplitude. Industrial systems must also account for common-mode range, output swing, noise gain, and grounding around the sensor. Place protection elements close to the connector, isolate high-current return paths from the amplifier ground reference, and verify operation across the complete input and output signal ranges.
Recommended
Recommended Products Summary
Engineering reference data for AD9632ARZ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Analog Devices |
| Package | 8-SOIC |
| Amplifier Architecture | Voltage feedback |
| Number of Circuits | 1 circuit |
| Small-Signal Bandwidth | 320 MHz |
| Large-Signal Bandwidth | 250 MHz at 4 V p-p |
| Slew Rate | 1500 V/us |
| Minimum Stable Gain | 2 V/V |
| Supply Voltage | ±6 V |
| Typical SFDR at 1 MHz | -113 dBc |
Key Differentiators
- High-speed gain stage with low distortion (vs AD9631)
- Strong large-signal performance (vs AD9631)
- Low spurious content for demanding signal chains (vs AD9631)
Design Notes
Keep the input, output, feedback, and ground paths short and route them as controlled-impedance traces. Place the feedback network directly beside the amplifier pins, and avoid adding long stubs or test-point branches near the high-impedance feedback node. Excess capacitance can move the amplifier toward oscillation or alter its distortion performance. A compact layout is especially important because the device provides 320 MHz small-signal bandwidth and 1500 V/us slew rate.
Place the supply-decoupling capacitors immediately adjacent to the amplifier's supply and ground pins, and select capacitors with adequate high-frequency behavior. The AD9632ARZ operates from ±6 V supplies, so each rail should remain within its specified operating range under transient load. Use a quiet, low-impedance ground return for the amplifier rather than sharing a narrow return path with unrelated high-current circuitry.
Confirm that the complete circuit provides closed-loop gain of 2 or greater before installation because the AD9632 is not unity-gain stable. Evaluate the feedback resistor values, source and load capacitance, and any cable or connector parasitics with the final layout. A gain-of-2 prototype that oscillates only at a particular frequency may indicate excessive feedback-node capacitance or an unintended gain configuration.
Do not treat the AD9632ARZ as a direct substitute for the unity-gain-stable AD9631 without reviewing the feedback topology and noise gain. Also check the ±6 V supply requirement, input common-mode limits, and output swing before power-up. The Analog Devices AD9632 datasheet, Rev. D, should be used to validate the final gain, termination, decoupling, and operating conditions.
Compliance Information
The available product information does not state the requested compliance attributes. Confirm current material and environmental declarations with Analog Devices before production release.