ADF4158CCPZ-RL7 - 6.1GHz Fractional-N RF Synthesizer | Analog Devices
MPN: ADF4158CCPZ-RL7 ✓ ActiveADF4158CCPZ-RL7 Overview
A fractional-N frequency synthesizer is a phase-locked-loop device that generates an adjustable output frequency from a stable reference while fractional-N feedback permits exceptionally fine frequency steps without requiring an impractically high prescaler. The ADF4158 belongs to the broader frequency synthesizer hierarchy: RF synthesizer, phase-locked loop, clock-and-timing IC, and semiconductor. Its architecture is intended for precise RF tuning while direct modulation provides a way to vary phase or frequency without relying solely on a separate modulation path.
The 25-bit fractional modulus is the core feature distinguishing the ADF4158 from integer-N synthesizers. According to the manufacturer datasheet, this architecture supports sub-hertz resolution at 6.1 GHz. The low-noise digital PFD and precision charge pump support stable phase locking, while the programmable reference divider accommodates different reference frequencies. Direct modulation and programmable waveform generation extend the device beyond basic local-oscillator synthesis, making it useful where phase, frequency, or calibrated waveform control is required.
The sigma-delta fractional interpolator enables the fractional-N mechanism by controlling the timing contribution of the N counter and divider output. This allows fine frequency increments while maintaining a relatively high PFD comparison frequency. Designers must still account for loop bandwidth, reference phase noise, VCO characteristics, and the bandwidth of the sigma-delta noise when optimizing phase noise and settling performance for a particular RF signal chain.
Typical applications include wireless infrastructure, test and measurement equipment, radar and communication systems, frequency-generation modules, and industrial RF control platforms. It is especially relevant where a compact RF synthesizer must cover frequencies up to 6.1 GHz and support direct modulation or waveform generation rather than only fixed-frequency clock multiplication.
PCB implementation requires careful attention to the exposed thermal pad, high-speed reference connections, charge-pump filtering, and power-supply decoupling. Use the pin-description table and reference-layout guidance in the manufacturer datasheet when assigning tracks and grounding the exposed pad. Keep sensitive RF and loop-filter nodes short, and verify the final lock performance with the intended reference and VCO rather than relying only on simulator results.
This product page consolidates the verified 6.1 GHz architecture, package information, sourcing terms, qualified replacement options, and application-specific engineering guidance into a single design reference. It also distinguishes true same-family drop-in choices from functionally similar devices that may require different programming, package details, or qualification.
Drop-in alternatives for ADF4158CCPZ-RL7 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ADF4158CCPZ-RL7 (same form factor and footprint) — differing in Charge Pump, Frequency Resolution, Phase-Frequency Detector.
ADF4158CCPZ
✅ Drop-InContact for price
View Datasheet →ADF4158WCCPZ-RL7
✅ Drop-In📋 Reference alternative (not in catalog)
ADF4158CCPZ-RL
✅ Drop-In📋 Reference alternative (not in catalog)
ADF4158CCPZ-R2
✅ Drop-In📋 Reference alternative (not in catalog)
ADF4169WCCPZ-RL7
✅ Drop-In📋 Reference alternative (not in catalog)
ADF4158CCPZ-RL7 Specifications
| Product Type | Fractional-N RF frequency synthesizer |
| Maximum Synthesis Frequency | 6.1 GHz |
| Fixed Modulus | 25 bit |
| Frequency Resolution | Sub-hertz at 6.1 GHz |
| Architecture | Fractional-N phase-locked loop |
| Modulation Capability | Direct modulation |
| Waveform Generation | Programmable |
| Phase-Frequency Detector | Digital, low noise |
| Charge Pump | Precision |
| Reference Divider | Programmable |
| Fractional Interpolator | Sigma-delta (Σ-Δ) |
| Pin Count | 24 pins |
| Package | 24-lead LFCSP with exposed pad |
| Mounting Type | Surface mount |
| Reference Input Frequency | 10 MHz |
ADF4158CCPZ-RL7 24-lead lfcsp with exposed pad Pin Configuration Guide
Pin configuration for ADF4158CCPZ-RL7 (24-lead lfcsp with exposed pad package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for ADF4158CCPZ-RL7.
Refer to the datasheet for full pin configuration.
Typical Applications
ADF4158CCPZ-RL7 is suitable for 6 applications: Wireless Infrastructure RF Synthesis, Test and Measurement Instruments, Radar and RF Signal Sources, Industrial RF Control Modules, Communications Equipment, Frequency Calibration and Tuning.
Wireless Infrastructure RF Synthesis
The ADF4158CCPZ-RL7 is suitable for wireless infrastructure equipment that needs programmable RF tuning across a range ending at 6.1 GHz. Its 25-bit fractional modulus produces sub-hertz theoretical frequency resolution at that upper limit, allowing channel settings to be placed more closely together than with an integer-N divider. The direct-modulation capability can reduce the need for a separate modulation path in suitable transmit architectures. Engineers should design the reference and loop-filter paths for low phase noise, and should verify output power, spur levels, settling time, and conducted emissions against the final system specification before production release.
Recommended
Test and Measurement Instruments
The ADF4158CCPZ-RL7 can provide a fine-resolution RF source for test and measurement equipment covering frequencies up to 6.1 GHz. The fractional-N architecture is useful when the instrument must select closely spaced frequencies while retaining a programmable output, and the waveform-generation function provides additional control beyond a basic integer-N synthesizer. In an instrument, the critical design work is the reference oscillator, loop bandwidth, VCO interface, calibration method, and output leveling. Confirm phase noise and spurious performance with the complete reference-and-VCO combination because the synthesizer IC alone does not determine the final output quality.
Recommended
Radar and RF Signal Sources
ADF4158CCPZ-RL7 applications include radar and RF signal-source subsystems requiring programmable frequency generation up to 6.1 GHz. Its direct modulation and waveform-generation functions allow phase or frequency behavior to be adjusted under software control, which is valuable for stimulus generation, fast frequency hops, or calibrated test sequences. The 25-bit fractional modulus permits fine tuning, but the achievable hopping rate and settling behavior depend on the programmed loop bandwidth and VCO dynamics. RF layout should isolate the reference and feedback paths from sensitive analog sections, while the exposed pad and LFCSP thermal path require adequate ground-plane copper.
Recommended
Industrial RF Control Modules
The ADF4158CCPZ-RL7 fits industrial RF control modules that need a compact synthesizer with fine frequency settings and programmable modulation. Its LFCSP package supports high-density RF board designs, while direct modulation can shorten the signal chain when the downstream mixer or amplifier accepts the generated waveform. Industrial deployments must account for reference-jitter tolerance, temperature drift, supply noise, and enclosure effects. Use the analog sections of the manufacturer datasheet to establish component placement around the PFD and charge-pump nodes, and validate locking across the required temperature and supply ranges rather than relying on nominal laboratory conditions.
Recommended
Communications Equipment
ADF4158CCPZ-RL7 is applicable to communications equipment requiring a programmable local oscillator with sub-hertz theoretical frequency resolution at 6.1 GHz. This precision is useful for narrow-channel synthesis, calibration tables, and digitally controlled RF tuning. The sigma-delta fractional interpolator implements the fractional division process, while the low-noise digital PFD and precision charge pump form the loop-control core. Designers should optimize loop bandwidth against phase noise and settling requirements and should use a clean reference because reference phase noise can dominate close-in synthesizer performance. RF output matching and PCB isolation also depend on the selected VCO and operating frequency.
Recommended
Frequency Calibration and Tuning
The ADF4158CCPZ-RL7 supports frequency calibration systems where a digitally programmed RF output must be swept or set to precise values. The 25-bit fixed modulus provides substantially finer control than a conventional integer-N synthesizer, while direct modulation adds flexibility during alignment or compensation procedures. A practical calibration setup should use a repeatable reference and characterize loop settling before recording coefficients. The charge-pump filter and sigma-delta settings determine both resolution behavior and noise bandwidth, so they should be tuned around the intended reference frequency. Keep programming and measurement paths separate from the sensitive RF section to reduce coupling during low-level measurements.
Recommended
Recommended Products Summary
Engineering reference data for ADF4158CCPZ-RL7 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ADF4158CCPZ | ADF4158WCCPZ-RL7 | ADF4158CCPZ-RL | ADF4158CCPZ-R2 | ADF4169WCCPZ-RL7 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad - same | 24-lead LFCSP with exposed pad - same | 24-lead LFCSP with exposed pad - same | 24-lead LFCSP with exposed pad - same | 24-lead LFCSP with exposed pad - same |
| Product Type | Fractional-N RF frequency synthesizer | Fractional-N RF frequency synthesizer | Fractional-N RF frequency synthesizer | Fractional-N RF frequency synthesizer | Fractional-N RF frequency synthesizer | Fractional-N RF frequency synthesizer |
| Pin Count | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins |
Key Differentiators
- Direct modulation and waveform generation in the same fractional-N device (vs ADF4158CCPZ)
- Sub-hertz theoretical resolution at the upper RF limit (vs ADF4158CCPZ-R2)
- Exact ordering option for a 24-lead LFCSP RF design (vs ADF4169WCCPZ-RL7)
Design Notes
Use the manufacturer reference-layout guidance as the starting point for the 24-lead LFCSP layout. Place supply bypass components directly at their designated pins, provide a continuous ground connection for the exposed pad, and route the reference, PFD, and charge-pump paths away from RF and digital return currents. The exposed pad is both a thermal connection and an electrical ground connection, so its via pattern and plane attachment should follow the datasheet drawing rather than an arbitrary via arrangement.
Treat the reference input and charge-pump filter as sensitive high-impedance nodes. Keep the loop-filter components close to their associated pins, remove unnecessary copper beneath noise-sensitive routes, and avoid shared return paths with switching supplies or high-current digital outputs. Reference phase noise, supply ripple, and charge-pump noise can each degrade close-in phase noise, so evaluate the complete reference, filter, and supply arrangement with measurement equipment capable of resolving the required spectral range.
Estimated: thermal performance depends on the PCB copper available to the exposed pad, ambient temperature, and total device dissipation. The actual dissipation should be calculated from the operating supply voltage, internal current, and external load. Validate the junction-temperature margin using the manufacturer thermal characterization and the final board stack-up. Do not size the exposed-pad copper from package dimensions alone, because airflow, copper area, and neighboring heat sources materially change the temperature rise.
Do not select a substitute solely from the package drawing or the 6.1 GHz headline rating. Check the suffix-specific temperature grade, qualification, pin assignments, register support, and programming procedure. The same ADF4158 family includes ordering variants with different suffixes, while ADF4169WCCPZ-RL7 changes the RF range and feature set. A board-level drop-in decision requires confirming the manufacturer pin table and application compatibility as well as the footprint.
Compliance Information
Compliance declarations were not established from the manufacturer product page or datasheet snippets and require confirmation from the exact Analog Devices ordering documentation.