Analog Devices

ADM232LJNZ - 5V Dual RS-232 Transceiver | Analog Devices

MPN: ADM232LJNZ ✓ Active
4.5 V to 5.5 V Vdss EIA-232-E and V.28 Rds(on) 16-pin PDIP Package
MOQ: 1 |

ADM232LJNZ Overview

The Analog Devices ADM232LJNZ is a dual-driver, dual-receiver RS-232 transceiver that operates from a single 4.5 V to 5.5 V supply. It supports data rates up to 100 kbps and is packaged in a 16-pin PDIP package. The device converts logic-level transmit and receive signals to and from RS-232-compatible line levels, allowing a 5 V system to communicate with legacy serial equipment.

An RS-232 transceiver is an interface integrated circuit within the broader communications-interface hierarchy. It combines line drivers, which translate CMOS logic into bipolar RS-232 signals, with receivers, which recover logic-level data from those signals. Because RS-232 uses voltage levels that can exceed the supply rails of modern CMOS logic, the onboard charge-pump circuitry generates the positive and negative voltages required on the bus.

Key characteristics of the ADM232LJNZ include its 5 V CMOS-compatible supply, 100 kbps maximum signaling rate, two transmit channels, two receive channels, and EIA-232-E and V.28 interface support. The single-supply architecture eliminates the need for a separate negative rail at the device interface. Its through-hole PDIP package is also suitable for legacy industrial control boards, laboratory equipment, and instrumentation where leaded components are preferred.

The ADM232L family was designed for communications interfaces where positive and negative 12 V rails are not available. Internally, the device combines transmit and receive functions in one package, reducing board area compared with separate driver and receiver ICs. External charge-pump capacitors are required, so the PCB layout must follow the manufacturer's recommended connection and grounding arrangement to achieve reliable operation and minimize transmitted noise.

Typical applications include legacy PC serial-port interfaces, industrial control panels, barcode and label equipment, test instruments, and embedded systems that communicate with RS-232 printers, scanners, or data acquisition units. The dual-channel arrangement allows one port to transmit while the other receives, which is useful for bidirectional console links and device-control protocols.

When designing around the ADM232LJNZ, connect the interface ground and signal ground carefully to minimize common-mode noise, place the charge-pump capacitors close to their assigned pins, and verify that every connected RS-232 port uses compatible signaling limits. The 100 kbps rate is suitable for moderate-speed control traffic, but it should not be selected for higher-bandwidth legacy serial links.

This page combines manufacturer specifications, package information, interface-family comparisons, and application-oriented design guidance. It also identifies pin-compatible RS-232 transceiver alternatives that can support sourcing decisions where the original 16-pin PDIP footprint must be retained.

Drop-in alternatives for ADM232LJNZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with ADM232LJNZ (same form factor and footprint) — differing in Product Type, Mounting Type, Package, Maximum Data Rate, Number of Drivers.

Analog Devices
Product Type: Dual RS-232 line-driver and line-receiver transceiver
Package: 16-lead plastic DIP
Number of Drivers: 2
Compare with ADM232LJNZ →
Analog Devices
Product Type: 2/2 RS-232 transceiver
Compare with ADM232LJNZ →
Analog Devices
Product Type: RS-232 transceiver
Compare with ADM232LJNZ →
Analog Devices
Number of Drivers: 4
Compare with ADM232LJNZ →
Texas Instruments
Product Type: RS-232 transceiver
Mounting Type: Through Hole
Maximum Data Rate: 250 kbps
Compare with ADM232LJNZ →

ADM232LJN

✅ Drop-In
Analog Devices
📦 16-PDIP
RS-232 transceiver · 2 transmitters and 2 receivers · 5 V · 120 kB/s · EIA-232-E and V.28 · Approximately ±9 V from a 5 V supply · Yes · 1 µF

Contact for price

View Datasheet →

ADM232LAN

✅ Drop-In
Analog Devices
📦 16-PDIP
2/2 RS-232 transceiver · 2 · 2 · 5 V · 120 kB/s · EIA-232-E and V.28 · Yes · 9 V

Contact for price

View Datasheet →

ADM232AAN

✅ Drop-In
Analog Devices
📦 16-PDIP
Dual RS-232 line-driver and line-receiver transceiver · 200 kB/s · 2 · 2 · 5 V · 0.1 µF · ±9 V with 5 V supply · ±30 V

Contact for price

View Datasheet →

MAX232EIN

✅ Drop-In
Texas Instruments
📦 16-PDIP
RS-232 transceiver · 2 · 2 · 4.5 V to 5.5 V · 5 V · 250 kbps · 16-pin PDIP · Through Hole

Contact for price

View Datasheet →

ADM232LJNZ Specifications

Device Type RS-232 transceiver
Driver and Receiver Configuration 2 drivers and 2 receivers
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Logic Technology 5 V CMOS
Maximum Data Rate 100 kbps
Interface Standard RS-232
Supported Signaling Standards EIA-232-E and V.28
Number of Pins 16 pins
Package 16-pin PDIP
Mounting Type Through-hole
Production Status Production
Negative Supply Requirement Not required at the device interface

ADM232LJNZ 16-pin pdip Pin Configuration Guide

Pin configuration for ADM232LJNZ (16-pin pdip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

16-pin pdip package pinout diagram for ADM232LJNZ

No detailed pinout data available for ADM232LJNZ.

Refer to the datasheet for full pin configuration.

Typical Applications

ADM232LJNZ is suitable for 6 applications: Legacy PC Serial-Port Interface, Industrial Control Panel Connectivity, Barcode and Label Printer Interface, Laboratory Test Instrument Control, Embedded Service Console, Data Acquisition Unit Connectivity.

🖥️

Legacy PC Serial-Port Interface

The ADM232LJNZ fits legacy PC and industrial-control serial ports that still use an RS-232 electrical interface. Its two transmitters and two receivers support one bidirectional communications channel while leaving the second pair available for handshake, status, or another low-speed link. Operation from 4.5 V to 5.5 V allows the circuit to share a regulated 5 V rail with the controlling logic, while the integrated charge-pump generates the bipolar line voltages required by RS-232.

🏭

Industrial Control Panel Connectivity

The ADM232LJNZ is appropriate for control panels that connect to older machinery, scales, or operator terminals over RS-232. Its 100 kbps rate is more than adequate for command traffic, configuration exchanges, and periodic status reporting, while the 16-pin PDIP package is convenient for leaded industrial boards and serviceable assemblies. The single 5 V supply requirement reduces the number of external rails, although the panel still needs careful signal-ground and surge-protection design.

📷

Barcode and Label Printer Interface

A barcode or label printer controller can use the ADM232LJNZ to bridge a 5 V UART to an RS-232 printer. The 100 kbps limit comfortably supports common printer command and response formats, and the integrated two-channel arrangement can carry data and control signals over one cable. For factory deployments, use the transmitter outputs only through the protection and filtering required by the installation environment, because RS-232 does not provide galvanic isolation.

🧪

Laboratory Test Instrument Control

The ADM232LJNZ is useful in laboratory instruments that must communicate with older RS-232 analyzers, printers, or programmable fixtures. A 100 kbps link provides sufficient throughput for instrument commands and measurement results, and the PDIP package simplifies assembly on custom test boards. Designers should treat the interface as a single-ended reference circuit: connect the instrument ground appropriately, minimize loop area, and add protection if the cable leaves the controlled enclosure.

🔧

Embedded Service Console

The ADM232LJNZ can provide a wired service port for embedded equipment that uses RS-232 for diagnostics, boot configuration, or field upgrades. The dual transmit and receive arrangement supports command and response traffic on one interface, and its 100 kbps maximum rate is practical for terminal sessions. A 5 V system can power the interface directly, but the external charge-pump capacitors should be positioned according to the recommended layout to minimize radiated and conducted noise.

📊

Data Acquisition Unit Connectivity

The ADM232LJNZ is suitable for data-acquisition equipment that must send sample records or configuration commands to a host computer over a legacy RS-232 connection. The 100 kbps rate supports moderate record volumes and supervisory protocols, while the 16-pin through-hole package fits older acquisition hardware. For long cables or noisy environments, add appropriate transient protection and keep the RS-232 signal ground connected according to the manufacturer's recommended interface topology.

What is the ADM232LJNZ?
The ADM232LJNZ is a dual-driver, dual-receiver RS-232 transceiver from Analog Devices. It operates from a 4.5 V to 5.5 V supply, supports signaling rates up to 100 kbps, and is intended for EIA-232-E and V.28 interfaces. The ADI product page describes the ADM232L as a low-power, +5 V CMOS RS-232 transceiver with two drivers and two receivers.
What package does the ADM232LJNZ use?
The ADM232LJNZ is offered in a 16-pin PDIP package with through-hole mounting. Distributor product records identify it as a 2/2 full RS-232 transceiver in a 16-pin PDIP. The Z designation denotes the PDIP package option, while the exact lead dimensions and pin numbering should be confirmed against the package drawing in the manufacturer datasheet.
What is the operating voltage of the ADM232LJNZ?
The ADM232LJNZ operates from a single 4.5 V to 5.5 V supply. According to the Analog Devices ADM232L product information, the device uses a +5 V CMOS supply and is intended for RS-232 applications where positive and negative 12 V rails are unavailable. Its internal charge-pump circuitry produces the bipolar line voltages required by the RS-232 interface.
What is the maximum data rate of the ADM232LJNZ?
The ADM232LJNZ supports a maximum signaling rate of 100 kbps. The manufacturer identifies the ADM232L as a low-power +5 V CMOS RS-232 transceiver with a 100 kbps data rate. This rate is suitable for control consoles, configuration protocols, and legacy peripherals, but it is below the throughput of faster RS-232 families designed for higher-speed synchronous communication.
Does the ADM232LJNZ need external negative voltage?
No. The ADM232LJNZ does not require an external negative 12 V supply. The Analog Devices ADM232L family description specifically targets EIA-232-E and V.28 interfaces where ±12 V is not available. On-chip charge-pump circuitry generates the required positive and negative line voltages, although external charge-pump capacitors must be connected as specified by the manufacturer.
Where can I download the ADM232LJNZ datasheet?
The official product documentation is available from the Analog Devices ADM232L product page at https://www.analog.com/en/products/adm232l.html. Select the Data Sheet document, identified as Revision C on the product page, and use the ADM232L pin and connection details to confirm the ADM232LJNZ ordering code. The datasheet contains the recommended charge-pump capacitor connections, logic diagrams, and operating limits.
Where is the ADM232LJNZ pinout?
The ADM232LJNZ pinout is shown in the Pin Configuration and Pin Function Descriptions sections of the manufacturer ADM232L datasheet. Because this listing is the 16-pin PDIP version, use the PDIP pin diagram rather than a SOIC or other package drawing. Assign PCB tracks from the datasheet pin table because the charge-pump, supply, driver-output, and receiver-input assignments must match the selected package exactly.
Is the ADM232LJNZ compatible with a 5 V microcontroller UART?
Yes. The ADM232LJNZ is designed for 5 V CMOS logic and includes two transmit inputs and two receive outputs for connection to a UART or other digital controller. The supply range is 4.5 V to 5.5 V. Confirm the logic-level thresholds and polarity in the datasheet, and connect the interface signal ground to the system ground through the layout recommended for EMC and noise control.
What is the difference between the ADM232LJNZ and ADM232LJN?
Both parts are identified as 2/2 full RS-232 transceivers in 16-pin PDIP packages. The ordering-code distinction indicates the packaging or lead-finish option, while the functional family provides the same 4.5 V to 5.5 V supply range and 100 kbps capability. Verify the exact suffix, dimensions, and finish against the manufacturer ordering guide before treating one as a mechanical substitute.
Is the MAX232EIN a drop-in replacement for the ADM232LJNZ?
The MAX232EIN is identified as a pin-compatible 16-pin PDIP RS-232 transceiver in cross-reference records, making it a candidate for footprint reuse. It is not a like-for-like replacement for every ADM232LJNZ build, so confirm supply voltage, driver and receiver counts, capacitor connections, and logic levels against both datasheets before production use. A footprint match alone does not guarantee identical AC performance or qualification.
When should I choose the ADM232LJNZ over another RS-232 transceiver?
Choose the ADM232LJNZ when the design requires a 2/2 RS-232 interface, a single 4.5 V to 5.5 V supply, signaling up to 100 kbps, and a 16-pin PDIP footprint. It is particularly appropriate for legacy industrial, laboratory, and instrumentation boards that still use through-hole components. For designs needing faster data rates, smaller surface-mount packages, or additional shutdown functions, select the device that explicitly provides those capabilities.
Is the ADM232LJNZ suitable for industrial equipment?
The ADM232LJNZ is suitable for many industrial and laboratory interfaces because it provides a complete 2/2 RS-232 transceiver from a single 5 V supply. Its through-hole PDIP package simplifies assembly and repair on older control boards. For equipment exposed to extended temperature, surge, vibration, or long product-life requirements, confirm the device-specific environmental ratings and any applicable industrial qualification before releasing the design.
What can replace the ADM232LJNZ?
The closest documented alternatives include the ADM232LJN, ADM232LAN, ADM232A, and MAX232EIN, all associated with 16-pin PDIP RS-232 transceiver configurations in cross-reference records. The maximum number of documented drop-in candidates for this exact footprint is limited, so each option should be checked for supply range, data rate, capacitor values, pin functions, and temperature grade. PCB compatibility must be verified against the manufacturer pin drawings.
What are the key specifications engineers should know about the ADM232LJNZ?
The key ADM232LJNZ specifications are a 4.5 V to 5.5 V supply, 2 drivers, 2 receivers, a 100 kbps maximum rate, EIA-232-E and V.28 support, and a 16-pin PDIP package. The device integrates the charge-pump function needed to generate RS-232 line voltages from a positive-only supply, reducing the external power-tree requirement compared with older discrete-driver designs.
Where can I buy the ADM232LJNZ online?
Use the Request a Quote form on this page to request the ADM232LJNZ with the required quantity, lead time, and delivery information. The form is the appropriate channel for current commercial terms and availability because distributor inventory and pricing change frequently. For technical confirmation, attach the required 16-pin PDIP footprint and your planned system supply voltage when requesting a quotation.
What is the lead time for the ADM232LJNZ?
The current lead time should be requested through the Request a Quote form on this page, including the required quantity and target delivery date. Because availability can vary by package option, lead time, and regional logistics, a quotation response provides the applicable commercial commitment. Engineers should also confirm whether the ADM232LJNZ or another package suffix is needed before committing to a schedule.
Is the ADM232LJNZ in stock?
Current stock for the ADM232LJNZ should be confirmed through the Request a Quote form on this page. Inventory status changes with order volume and purchasing activity, and the required tube, cut-tape, or other delivery configuration can affect availability. Submit the target quantity and packaging requirement so the response can reflect the correct production and distribution position.

Engineering reference data for ADM232LJNZ — comparison, design guidance, and compliance information.

Selection Guide

Choose the ADM232LJNZ when the PCB already uses a 16-pin PDIP footprint and the system needs two RS-232 drivers plus two receivers from one 4.5 V to 5.5 V supply. It is a strong fit for legacy industrial controls, laboratory instruments, service consoles, and printer interfaces operating at 100 kbps or below. ADM232LJN or ADM232LAN may be preferable when an equivalent same-family ordering option is available. ADM232A should be selected only after its electrical and environmental ratings are confirmed. MAX232EIN is the documented cross-brand candidate when an alternate manufacturer is acceptable, but verify capacitor values, temperature range, data rate, and exact pin functions. For new designs needing more than 100 kbps, only one channel, automatic shutdown, or a surface-mount package, choose a newer transceiver rather than forcing a footprint substitution.

Comparison with Alternatives

Parameter This Product ADM232LJN ADM232LAN ADM232A MAX232EIN
Brand Analog Devices Analog Devices Analog Devices Analog Devices Maxim Integrated
Package 16-PDIP 16-PDIP 16-PDIP 16-PDIP 16-PDIP
Device Function Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver RS-232 transceiver Dual RS-232 transceiver
Mounting Style Through-hole Through-hole Through-hole Through-hole Through-hole
Number of Pins 16 pins 16 pins 16 pins 16 pins 16 pins

Key Differentiators

  • Complete dual-channel interface in one 16-pin PDIP device (vs MC1488NE4)
  • Single positive supply simplifies system power design (vs MAX232EIN)
  • Direct same-family sourcing within the ADM232L footprint (vs ADM232LAN)
  • Higher stated throughput than a standard 100 kbps RS-232 interface (vs MAX3221IPWR)

Design Notes

Place the charge-pump capacitors directly beside their associated IC pins and follow the exact connection shown in the ADM232L datasheet. Keep the RS-232 driver traces short and route them away from sensitive analog or high-speed digital nets. Because the device generates bipolar line voltages internally, a compact capacitor loop reduces radiated emissions and helps prevent switching noise from appearing on the serial outputs.

Connect the interface ground as specified for the RS-232 port rather than treating it as an optional high-current return path. Keep the logic ground, interface ground, and connector reference arrangement compatible with the system grounding strategy. A single reference connection is generally preferable to multiple chassis bonds, which can create ground loops when the RS-232 cable connects equipment installed at different potentials.

Do not treat the ADM232LJNZ as a differential RS-485 transceiver or connect its driver outputs to a CAN bus. Verify the 16-pin PDIP footprint, charge-pump capacitor values, supply decoupling, and logic thresholds before assembly. Also confirm that the remote equipment actually uses RS-232 voltage levels; a TTL serial port without level translation is not a direct substitute for the transceiver.

For cables longer than a short bench connection, add appropriately rated protection at the connector and provide a defined chassis or signal-ground strategy. RS-232 is single-ended and can pick up common-mode noise on long routes. Keep unprotected driver traces away from motor, relay, and switching-power circuits, and verify conducted and radiated emissions after the complete equipment configuration has been assembled.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The Analog Devices product page identifies the ADM232L family as production, but the accessible product information does not state device-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose RS-232 interface IC.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

ADM232LJNZ datasheet ADM232LJNZ pinout ADM232LJNZ datasheet pdf ADM232LJNZ specifications ADM232LJNZ RS-232 transceiver ADM232LJNZ 16-pin PDIP ADM232LJNZ equivalent ADM232LJNZ drop-in replacement ADM232LJNZ vs MAX232EIN ADM232LJNZ application circuit ADM232LJNZ price ADM232LJNZ stock Analog Devices ADM232LJNZ ADM232LJNZ lead time

Related Components & Terms

Analog Devices ADM232LJNZ ADM232L ADM232LJN ADM232LAN ADM232A MAX232EIN Maxim Integrated RS-232 transceiver line driver line receiver EIA-232-E V.28 5 V CMOS charge-pump circuit 16-pin PDIP through-hole package single-supply interface serial communications industrial control legacy PC serial port printer interface data acquisition EMI
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details