ADM232LJNZ - 5V Dual RS-232 Transceiver | Analog Devices
MPN: ADM232LJNZ ✓ সক্রিয়ADM232LJNZ সারাংশ
An RS-232 transceiver is an interface integrated circuit within the broader communications-interface hierarchy. It combines line drivers, which translate CMOS logic into bipolar RS-232 signals, with receivers, which recover logic-level data from those signals. Because RS-232 uses voltage levels that can exceed the supply rails of modern CMOS logic, the onboard charge-pump circuitry generates the positive and negative voltages required on the bus.
Key characteristics of the ADM232LJNZ include its 5 V CMOS-compatible supply, 100 kbps maximum signaling rate, two transmit channels, two receive channels, and EIA-232-E and V.28 interface support. The single-supply architecture eliminates the need for a separate negative rail at the device interface. Its through-hole PDIP package is also suitable for legacy industrial control boards, laboratory equipment, and instrumentation where leaded components are preferred.
The ADM232L family was designed for communications interfaces where positive and negative 12 V rails are not available. Internally, the device combines transmit and receive functions in one package, reducing board area compared with separate driver and receiver ICs. External charge-pump capacitors are required, so the PCB layout must follow the manufacturer's recommended connection and grounding arrangement to achieve reliable operation and minimize transmitted noise.
Typical applications include legacy PC serial-port interfaces, industrial control panels, barcode and label equipment, test instruments, and embedded systems that communicate with RS-232 printers, scanners, or data acquisition units. The dual-channel arrangement allows one port to transmit while the other receives, which is useful for bidirectional console links and device-control protocols.
When designing around the ADM232LJNZ, connect the interface ground and signal ground carefully to minimize common-mode noise, place the charge-pump capacitors close to their assigned pins, and verify that every connected RS-232 port uses compatible signaling limits. The 100 kbps rate is suitable for moderate-speed control traffic, but it should not be selected for higher-bandwidth legacy serial links.
This page combines manufacturer specifications, package information, interface-family comparisons, and application-oriented design guidance. It also identifies pin-compatible RS-232 transceiver alternatives that can support sourcing decisions where the original 16-pin PDIP footprint must be retained.
এর জন্য ড্রপ-ইন বিকল্প ADM232LJNZ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible ADM232LJNZ (একই form factor এবং footprint) — পার্থক্য রয়েছে Product Type, Mounting Type, Package, Maximum Data Rate, Number of Drivers.
ADM232LJN
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →ADM232LAN
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →ADM232AAN
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX232EIN
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →ADM232LJNZ বিশেষণ
| Device Type | RS-232 transceiver |
| Driver and Receiver Configuration | 2 drivers and 2 receivers |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Logic Technology | 5 V CMOS |
| Maximum Data Rate | 100 kbps |
| Interface Standard | RS-232 |
| Supported Signaling Standards | EIA-232-E and V.28 |
| পিনের সংখ্যা | 16 pins |
| প্যাকেজ | 16-pin PDIP |
| মাউন্টিং টাইপ | Through-hole |
| Production Status | Production |
| Negative Supply Requirement | Not required at the device interface |
ADM232LJNZ 16-pin pdip পিন কনফিগারেশন গাইড
ADM232LJNZ (16-pin pdip প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ADM232LJNZ.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ADM232LJNZ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Legacy PC Serial-Port Interface, Industrial Control Panel Connectivity, Barcode and Label Printer Interface, Laboratory Test Instrument Control, Embedded Service Console, Data Acquisition Unit Connectivity.
Legacy PC Serial-Port Interface
The ADM232LJNZ fits legacy PC and industrial-control serial ports that still use an RS-232 electrical interface. Its two transmitters and two receivers support one bidirectional communications channel while leaving the second pair available for handshake, status, or another low-speed link. Operation from 4.5 V to 5.5 V allows the circuit to share a regulated 5 V rail with the controlling logic, while the integrated charge-pump generates the bipolar line voltages required by RS-232.
সুপারিশকৃত
Industrial Control Panel Connectivity
The ADM232LJNZ is appropriate for control panels that connect to older machinery, scales, or operator terminals over RS-232. Its 100 kbps rate is more than adequate for command traffic, configuration exchanges, and periodic status reporting, while the 16-pin PDIP package is convenient for leaded industrial boards and serviceable assemblies. The single 5 V supply requirement reduces the number of external rails, although the panel still needs careful signal-ground and surge-protection design.
সুপারিশকৃত
Barcode and Label Printer Interface
A barcode or label printer controller can use the ADM232LJNZ to bridge a 5 V UART to an RS-232 printer. The 100 kbps limit comfortably supports common printer command and response formats, and the integrated two-channel arrangement can carry data and control signals over one cable. For factory deployments, use the transmitter outputs only through the protection and filtering required by the installation environment, because RS-232 does not provide galvanic isolation.
সুপারিশকৃত
Laboratory Test Instrument Control
The ADM232LJNZ is useful in laboratory instruments that must communicate with older RS-232 analyzers, printers, or programmable fixtures. A 100 kbps link provides sufficient throughput for instrument commands and measurement results, and the PDIP package simplifies assembly on custom test boards. Designers should treat the interface as a single-ended reference circuit: connect the instrument ground appropriately, minimize loop area, and add protection if the cable leaves the controlled enclosure.
সুপারিশকৃত
Embedded Service Console
The ADM232LJNZ can provide a wired service port for embedded equipment that uses RS-232 for diagnostics, boot configuration, or field upgrades. The dual transmit and receive arrangement supports command and response traffic on one interface, and its 100 kbps maximum rate is practical for terminal sessions. A 5 V system can power the interface directly, but the external charge-pump capacitors should be positioned according to the recommended layout to minimize radiated and conducted noise.
সুপারিশকৃত
Data Acquisition Unit Connectivity
The ADM232LJNZ is suitable for data-acquisition equipment that must send sample records or configuration commands to a host computer over a legacy RS-232 connection. The 100 kbps rate supports moderate record volumes and supervisory protocols, while the 16-pin through-hole package fits older acquisition hardware. For long cables or noisy environments, add appropriate transient protection and keep the RS-232 signal ground connected according to the manufacturer's recommended interface topology.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ADM232LJNZ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | ADM232LJN | ADM232LAN | ADM232A | MAX232EIN |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated |
| Package | 16-PDIP | 16-PDIP | 16-PDIP | 16-PDIP | 16-PDIP |
| Device Function | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | RS-232 transceiver | Dual RS-232 transceiver |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Number of Pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
মূল পার্থক্যসমূহ
- Complete dual-channel interface in one 16-pin PDIP device (বনামMC1488NE4)
- Single positive supply simplifies system power design (বনামMAX232EIN)
- Direct same-family sourcing within the ADM232L footprint (বনামADM232LAN)
- Higher stated throughput than a standard 100 kbps RS-232 interface (বনামMAX3221IPWR)
ডিজাইন নোট
Place the charge-pump capacitors directly beside their associated IC pins and follow the exact connection shown in the ADM232L datasheet. Keep the RS-232 driver traces short and route them away from sensitive analog or high-speed digital nets. Because the device generates bipolar line voltages internally, a compact capacitor loop reduces radiated emissions and helps prevent switching noise from appearing on the serial outputs.
Connect the interface ground as specified for the RS-232 port rather than treating it as an optional high-current return path. Keep the logic ground, interface ground, and connector reference arrangement compatible with the system grounding strategy. A single reference connection is generally preferable to multiple chassis bonds, which can create ground loops when the RS-232 cable connects equipment installed at different potentials.
Do not treat the ADM232LJNZ as a differential RS-485 transceiver or connect its driver outputs to a CAN bus. Verify the 16-pin PDIP footprint, charge-pump capacitor values, supply decoupling, and logic thresholds before assembly. Also confirm that the remote equipment actually uses RS-232 voltage levels; a TTL serial port without level translation is not a direct substitute for the transceiver.
For cables longer than a short bench connection, add appropriately rated protection at the connector and provide a defined chassis or signal-ground strategy. RS-232 is single-ended and can pick up common-mode noise on long routes. Keep unprotected driver traces away from motor, relay, and switching-power circuits, and verify conducted and radiated emissions after the complete equipment configuration has been assembled.
কমপ্লায়েন্স তথ্য
The Analog Devices product page identifies the ADM232L family as production, but the accessible product information does not state device-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose RS-232 interface IC.