Analog Devices

ADM237LJN - 120kbps 5V RS-232 Interface IC | Analog Devices

MPN: ADM237LJN ✓ Active
5 V Vdss ≤1 µA Id EIA-232-E and V.28 Rds(on) 24-pin PDIP Package
MOQ: 1 |

ADM237LJN Overview

The Analog Devices ADM237LJN is a 5 V powered CMOS RS-232 interface IC with five drivers, three receivers, a 120 kbps data rate, and onboard DC-to-DC converters that produce approximately ±9 V output swing. The device is supplied in a 24-pin PDIP package. According to the manufacturer datasheet, it meets EIA-232-E and V.28 specifications, supports low-power shutdown at 1 µA or less, and accepts receiver input voltages of ±30 V.

An RS-232 interface IC is a transceiver that connects low-voltage digital logic to a bipolar serial communications port. It combines line drivers, which convert CMOS logic into RS-232 voltage levels, with line receivers, which convert RS-232 signals back into CMOS-compatible logic. As an interface IC within the broader semiconductor category, the ADM237LJN allows equipment to communicate with RS-232 devices when a conventional ±12 V supply and external level-shifting circuitry are unavailable.

The ADM237LJN operates from a single 5 V supply while generating the bipolar voltage levels required for RS-232 transmission. Its onboard DC-to-DC converters produce approximately ±9 V output swing, while the use of small 1 µF capacitors helps reduce the external support-component burden. The 120 kbps maximum data rate supports legacy serial links commonly found in industrial-control, instrumentation, test-equipment, and point-of-sale systems.

The five-driver and three-receiver arrangement supports multiple RS-232 channels without requiring a separate interface IC for every line. Shutdown control can reduce supply consumption to 1 µA or less when the interface is not active. Receiver inputs tolerate ±30 V, improving robustness against voltage transients encountered on long or noisy cable connections. These characteristics make the device useful where a single logic supply must also support a physical-layer port protected from moderate overstress.

Typical applications include industrial serial controllers, laboratory instruments, barcode and point-of-sale equipment, data-acquisition systems, and service interfaces on embedded products. In these systems, the ADM237LJN can bridge UART or general-purpose I/O signals to an RS-232 connector. Designers should still provide appropriate cable protection, grounding, and connector-level surge mitigation for installations where cables extend beyond controlled equipment wiring.

A key design consideration is that the ADM237LJN is intended for RS-232 rather than RS-485 or RS-422 signaling. Its onboard charge-pump converters and driver outputs create bipolar RS-232 levels, so the transceiver cannot be connected directly to a differential RS-485 bus. Review the datasheet pin and capacitor recommendations before layout because converter and charge-pump performance depends on correct capacitor placement and low-impedance supply routing.

This page combines the manufacturer electrical capabilities, package details, interface applications, design guidance, and validated cross-reference findings. It also distinguishes genuine same-footprint drop-in options from superficially similar RS-232 transceivers whose pin counts or electrical functions do not permit PCB-level substitution.

Drop-in alternatives for ADM237LJN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with ADM237LJN (same form factor and footprint) — differing in Package, Product Type.

Analog Devices
Package: 24-pin DIP, 7.62 mm row spacing
Product Type: RS-232 driver/receiver transceiver IC
Compare with ADM237LJN →

No drop-in alternatives available for this product.

Request Alternatives

ADM237LJN Specifications

Product Type RS-232 transceiver interface IC
Supply Voltage 5 V
Data Rate 120 kbps
Driver Count 5 drivers
Receiver Count 3 receivers
Onboard DC-to-DC Converter Output Swing ±9 V
External Capacitor Value 1 µF
Low-Power Shutdown Current ≤1 µA
Receiver Input Voltage Tolerance ±30 V
RS-232 Standards EIA-232-E and V.28
Logic Technology 5 V CMOS
Package 24-pin PDIP
Mounting Type Through-hole
Latch-Up Protection Latch-up free

ADM237LJN 24-pin pdip Pin Configuration Guide

Pin configuration for ADM237LJN (24-pin pdip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

24-pin pdip package pinout diagram for ADM237LJN

No detailed pinout data available for ADM237LJN.

Refer to the datasheet for full pin configuration.

Typical Applications

ADM237LJN is suitable for 6 applications: Industrial Serial Control Interfaces, Laboratory Instrument Serial Ports, Point-of-Sale and Peripheral Equipment, Data-Acquisition and Test Systems, Embedded Equipment Service Ports, Legacy Equipment Retrofit.

🏭

Industrial Serial Control Interfaces

The ADM237LJN fits industrial controllers that need several RS-232 lines but have only a 5 V logic supply. Its five drivers and three receivers support multiple command, status, and data paths, while the onboard DC-to-DC converters generate approximately ±9 V output swing without external negative rails. The 120 kbps rate is appropriate for conventional supervisory and configuration links rather than high-speed bulk transfer. Designers should allocate the required 1 µF capacitors close to the converter pins and provide cable-side protection when the port connects to external equipment.

🔧

Laboratory Instrument Serial Ports

The ADM237LJN is useful in laboratory instruments that expose an RS-232 service or control port while operating from a single 5 V rail. Five driver channels can support multiple control lines and three receiver channels can handle status or command feedback at rates up to 120 kbps. Its ±30 V receiver-input tolerance improves robustness on laboratory benches where connected equipment may produce ground offsets or transient excursions. The through-hole PDIP package also simplifies prototype construction and replacement in service-oriented equipment.

🖥️

Point-of-Sale and Peripheral Equipment

Point-of-sale terminals and peripheral controllers commonly rely on established RS-232 command links that do not require data rates above 120 kbps. The ADM237LJN provides five drivers and three receivers for multiple peripheral functions while deriving the required bipolar line levels from one 5 V supply. This removes the need for separate ±12 V circuitry and reduces external converter design effort. Firmware should confirm whether each attached peripheral requires a particular handshake signal, and the PCB must preserve the device's converter-capacitor layout for reliable operation.

📺

Data-Acquisition and Test Systems

The ADM237LJN can provide a legacy RS-232 command path in data-acquisition and automated test systems that retain compatibility with older instruments. The 120 kbps maximum rate is sufficient for configuration commands, status reporting, and short measurement transfers, while five transmitter channels can coordinate multiple control lines. A single 5 V supply simplifies the analog and digital power sections of larger instruments. For installation environments with long cables, add appropriate external surge and ESD protection because the receiver's ±30 V tolerance is not a substitute for a designed protection network.

🧩

Embedded Equipment Service Ports

The ADM237LJN is appropriate for embedded machinery and appliances that retain an RS-232 service connector for configuration, diagnostics, or firmware recovery. It requires only a 5 V supply and produces approximately ±9 V output swing through onboard converters, allowing service-port functionality to coexist with a compact digital power architecture. The shutdown mode draws 1 µA or less, which can reduce consumption when the interface is intentionally inactive. Firmware and connector wiring must be designed to prevent unwanted transitions during startup, reset, and firmware-update procedures.

🔧

Legacy Equipment Retrofit

The ADM237LJN supports retrofit and modernization projects that must preserve an RS-232 interface on older equipment. Its 24-pin PDIP package is useful for repair boards and prototype adapters where surface-mount assembly is less convenient. Five drivers and three receivers cover multiple legacy control and status lines at up to 120 kbps. The interface is bipolar and single-ended, so it cannot be connected to an RS-485 differential bus without additional circuitry. Mechanical retention, connector grounding, and cable shielding should be reviewed alongside the electronic interface.

What is the ADM237LJN and what does it do?
The ADM237LJN is a 5 V powered CMOS RS-232 transceiver containing five drivers, three receivers, and onboard DC-to-DC converters. According to the manufacturer datasheet, it supports data rates up to 120 kbps and generates approximately ±9 V output swing from a single 5 V supply. It is intended for systems that need bidirectional and unidirectional RS-232 links without separate ±12 V power rails.
What is the maximum data rate of the ADM237LJN?
The ADM237LJN supports a maximum data rate of 120 kbps. This figure comes from the manufacturer datasheet and describes the digital signaling rate for the integrated RS-232 drivers and receivers. It is suitable for established UART-based equipment links, but it should not be selected for a protocol requiring data rates above 120 kbps or for differential RS-485 and RS-422 networks.
Does the ADM237LJN need a separate ±12 V supply?
No, the ADM237LJN operates from a single 5 V supply and uses onboard DC-to-DC converters to create the bipolar drive voltage required for RS-232. The manufacturer datasheet specifies approximately ±9 V output swing with the 5 V supply. This simplifies the power architecture compared with a conventional RS-232 transceiver that requires separate positive and negative supply rails.
What package does the ADM237LJN use?
The ADM237LJN is packaged in a 24-pin PDIP with through-hole mounting. The DigiKey product listing identifies the package as 24-PDIP, while the manufacturer datasheet identifies the device as a 5 V powered CMOS RS-232 driver and receiver family member. Confirm the complete pin description table in the manufacturer datasheet before assigning connector, supply, and interface signals to the PCB.
Where can I download the ADM237LJN datasheet PDF?
The ADM237LJN datasheet PDF is available from the document link on this page and from the Analog Devices ADM237L data-sheet links listed in the page resources. The document describes the 5 V CMOS RS-232 drivers and receivers, EIA-232-E and V.28 compliance, 120 kbps operation, external capacitor requirements, and the 24-pin PDIP pin description. Use the manufacturer document for final design approval.
Where can I find the ADM237LJN pinout?
The ADM237LJN pinout is identified in the pin-description table of the manufacturer datasheet. The device uses a 24-pin PDIP outline with five drivers, three receivers, power inputs, shutdown control, and charge-pump capacitor connections. Because the complete pin names are not listed on this page, use the numbered manufacturer pin table and the package drawing when assigning tracks.
Can the ADM237LJN connect to an RS-485 bus?
No, the ADM237LJN is an RS-232 transceiver and cannot be connected directly to an RS-485 bus. Its drivers produce bipolar single-ended signaling for V.28 and EIA-232-E interfaces, whereas RS-485 uses a differential pair and a different transceiver topology. Select an RS-485 interface IC for a differential bus; using the ADM237LJN there could cause incorrect signaling and damage connected equipment.
How much current does the ADM237LJN draw in shutdown?
The ADM237LJN draws 1 µA or less during low-power shutdown. According to the manufacturer datasheet, shutdown reduces power dissipation while the receiver structure remains active. This makes the shutdown control useful in battery-operated or intermittently connected instruments, although the overall system saving also depends on how the external UART and connector interface are managed.
What can replace the ADM237LJN?
A valid replacement must use the same 24-pin PDIP footprint, preserve pin-to-pin signal assignments, and meet the required 5 V RS-232 electrical specifications. No separately documented drop-in replacement was confirmed by the available cross-reference results. Several RS-232 transceivers use fewer pins or provide fewer driver and receiver channels, so selecting one without a manufacturer pin-for-pin comparison could require PCB changes.
Is ADM237LJN the same as ADM232LJN?
No, ADM237LJN and ADM232LJN are not automatically interchangeable. The ADM237LJN is identified as a 24-pin PDIP device with five drivers and three receivers, while the cross-reference results identify ADM232LJN as a 16-pin PDIP RS-232 device. The different package and pin count prevent a direct drop-in substitution without redesigning the PCB.
What is the best Analog Devices equivalent for the ADM237LJN?
The closest validated family choice must be checked against the required channel count, shutdown behavior, package, and connector-side pinout. The available cross-reference results do not document an Analog Devices part that is both pin-to-pin compatible with the ADM237LJN and electrically equivalent. Do not substitute ADM232LJN or another RS-232 transceiver solely because the interface protocol matches; verify the 24-pin footprint and every signal assignment first.
When should I choose the ADM237LJN over another RS-232 transceiver?
Choose the ADM237LJN when the design needs five RS-232 drivers, three receivers, operation from one 5 V rail, and a 24-pin PDIP footprint at rates up to 120 kbps. Choose a smaller-channel or surface-mount device when the system uses fewer lines, requires a compact PCB, or needs specifications not provided by this part. The onboard converters and through-hole package are the main architectural trade-offs.
Is the ADM237LJN suitable for industrial serial equipment?
The ADM237LJN is suitable for many industrial serial interfaces because it supports EIA-232-E and V.28 signaling from a single 5 V supply and tolerates receiver inputs of ±30 V. Its 120 kbps rate suits conventional control and instrumentation links. The final enclosure and cable design still needs appropriate surge and ESD protection for the installation environment.
What capacitors does the ADM237LJN require?
The manufacturer datasheet specifies small 1 µF capacitors for the ADM237LJN implementation. These capacitors support the onboard DC-to-DC converter and charge-pump functions that create the bipolar RS-232 output swing. Their voltage rating, tolerance, type, and placement should follow the manufacturer recommendation, and the converter-capacitor traces should be kept short and away from sensitive input nodes.
Where to buy the ADM237LJN online?
Use the Request a Quote form on this page to request the ADM237LJN and confirm current supply, lot traceability, packaging, and delivery timing. The structured product data includes manufacturer and distributor references for technical review, but current commercial terms should be confirmed through the quote process because inventory and lead time can change without notice.
What is the price of the ADM237LJN?
The current commercial price for the ADM237LJN should be requested through the Request a Quote form on this page. The form can confirm quantity pricing, expected delivery, and the exact ordering suffix. No static price is stated because transaction terms and market conditions change independently of the component's technical specifications.
What is the lead time for the ADM237LJN?
Request the current lead time and minimum order quantity for the ADM237LJN through the Request a Quote form on this page. Lead time can vary with order quantity, packaging requirements, manufacturing schedules, and supply availability. A current quotation provides the most reliable confirmation for production planning.
Is the ADM237LJN in stock?
Current stock for the ADM237LJN should be confirmed through the Request a Quote form on this page. The component's technical attributes do not establish present inventory, and no reliable stock quantity should be inferred from a general product listing. Request the exact ADM237LJN suffix and required quantity when seeking an allocation.

Engineering reference data for ADM237LJN — comparison, design guidance, and compliance information.

Selection Guide

Choose the ADM237LJN when an equipment design needs a 5 V-only RS-232 interface with five drivers, three receivers, a 120 kbps limit, and a 24-pin PDIP footprint. Its onboard converters eliminate the need for separate ±12 V rails, making it attractive for prototypes and legacy equipment that retains a through-hole service port. Choose a smaller RS-232 transceiver when the system uses fewer channels or requires a surface-mount package, but verify shutdown behavior and receiver specifications before substituting. Do not select ADM232LJN as a drop-in option because its documented 16-pin PDIP configuration differs from the ADM237LJN's 24-pin footprint. Likewise, RS-485 and RS-422 devices are not substitutes even if their signaling rates are similar. For new production, confirm lifecycle status, operating-temperature limits, and exact ordering information through the manufacturer documentation and the Request a Quote form.

Comparison with Alternatives

Parameter This Product
Brand Analog Devices
Package 24-pin PDIP
Interface Type RS-232
Supply Voltage 5 V
Maximum Data Rate 120 kbps
Driver Count 5 drivers
Receiver Count 3 receivers
Generated Output Swing ±9 V
Shutdown Current ≤1 µA
Receiver Input Tolerance ±30 V

Key Differentiators

  • High channel count for a 5 V RS-232 transceiver (vs ADM232LJN)
  • Single-supply bipolar drive capability (vs Conventional external ±12 V RS-232 interface)
  • Improved receiver overstress tolerance (vs Basic RS-232 receiver implementations)

Design Notes

Place the manufacturer's specified 1 µF converter capacitors close to their corresponding ADM237LJN pins and keep the associated charge-pump traces short. Use a low-impedance connection from the device's supply pins to the 5 V rail, and avoid routing converter currents beneath sensitive receiver inputs. Follow the capacitor type and voltage-rating guidance in the manufacturer datasheet because ESR and tolerance can affect converter behavior.

Keep RS-232 driver outputs away from receiver inputs and digital timing nets to reduce capacitive and ground-current coupling. Route the connector side of the interface as an unbalanced network with a defined signal-ground relationship to the logic ground. Where the cable leaves the enclosure, provide appropriately coordinated surge and ESD protection; the advertised ±30 V receiver tolerance should not be treated as a complete cable-protection design.

Do not replace this RS-232 transceiver with a similarly labeled RS-485 or RS-422 device without redesigning the interface. The ADM237LJN provides single-ended bipolar signaling and onboard charge pumps, whereas differential bus devices use different driver and receiver circuits. Also avoid assigning signals from a partial pin listing: use the complete manufacturer pin-description table to identify converter capacitors, shutdown control, driver outputs, and receiver inputs.

Budget the 5 V supply for both normal operation and the current required by the onboard DC-to-DC converters. Decouple the device close to its supply pins and verify startup behavior across the intended supply range, especially when multiple RS-232 ports share the same rail. Although shutdown current is specified at 1 µA or less, the normal operating consumption and external load behavior must be evaluated separately.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The manufacturer datasheet identifies the device as latch-up free and compliant with EIA-232-E and V.28, but no RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration is established by the available material.

Related Searches

ADM237LJN datasheet ADM237LJN datasheet pdf ADM237LJN pinout ADM237LJN specifications ADM237LJN equivalent ADM237LJN replacement ADM237LJN cross reference ADM237LJN vs ADM232LJN ADM237LJN 24 PDIP ADM237LJN 120 kbps ADM237LJN 5 V RS-232 ADM237LJN application circuit Analog Devices ADM237LJN ADM237LJN price ADM237LJN buy online

Related Components & Terms

Analog Devices ADM237LJN ADM232LJN RS-232 EIA-232-E V.28 CMOS RS-232 transceiver line driver line receiver interface IC semiconductor onboard DC-to-DC converter charge-pump capacitor 120 kbps 5 V supply ±9 V output swing ±30 V receiver input 1 µF capacitor 24-pin PDIP surface-mount alternative industrial control laboratory instrumentation
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details