ADM237LJN - 120kbps 5V RS-232 Interface IC | Analog Devices
N.º de pieza: ADM237LJN ✓ ActivoADM237LJN Descripción general
An RS-232 interface IC is a transceiver that connects low-voltage digital logic to a bipolar serial communications port. It combines line drivers, which convert CMOS logic into RS-232 voltage levels, with line receivers, which convert RS-232 signals back into CMOS-compatible logic. As an interface IC within the broader semiconductor category, the ADM237LJN allows equipment to communicate with RS-232 devices when a conventional ±12 V supply and external level-shifting circuitry are unavailable.
The ADM237LJN operates from a single 5 V supply while generating the bipolar voltage levels required for RS-232 transmission. Its onboard DC-to-DC converters produce approximately ±9 V output swing, while the use of small 1 µF capacitors helps reduce the external support-component burden. The 120 kbps maximum data rate supports legacy serial links commonly found in industrial-control, instrumentation, test-equipment, and point-of-sale systems.
The five-driver and three-receiver arrangement supports multiple RS-232 channels without requiring a separate interface IC for every line. Shutdown control can reduce supply consumption to 1 µA or less when the interface is not active. Receiver inputs tolerate ±30 V, improving robustness against voltage transients encountered on long or noisy cable connections. These characteristics make the device useful where a single logic supply must also support a physical-layer port protected from moderate overstress.
Typical applications include industrial serial controllers, laboratory instruments, barcode and point-of-sale equipment, data-acquisition systems, and service interfaces on embedded products. In these systems, the ADM237LJN can bridge UART or general-purpose I/O signals to an RS-232 connector. Designers should still provide appropriate cable protection, grounding, and connector-level surge mitigation for installations where cables extend beyond controlled equipment wiring.
A key design consideration is that the ADM237LJN is intended for RS-232 rather than RS-485 or RS-422 signaling. Its onboard charge-pump converters and driver outputs create bipolar RS-232 levels, so the transceiver cannot be connected directly to a differential RS-485 bus. Review the datasheet pin and capacitor recommendations before layout because converter and charge-pump performance depends on correct capacitor placement and low-impedance supply routing.
This page combines the manufacturer electrical capabilities, package details, interface applications, design guidance, and validated cross-reference findings. It also distinguishes genuine same-footprint drop-in options from superficially similar RS-232 transceivers whose pin counts or electrical functions do not permit PCB-level substitution.
Alternativas directas para ADM237LJN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADM237LJN (mismo factor de forma y huella) — difiere en Package, Product Type.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasADM237LJN Especificaciones
| Product Type | RS-232 transceiver interface IC |
| Tensión de alimentación | 5 V |
| Velocidad de datos | 120 kbps |
| Driver Count | 5 drivers |
| Receiver Count | 3 receivers |
| Onboard DC-to-DC Converter Output Swing | ±9 V |
| External Capacitor Value | 1 µF |
| Low-Power Shutdown Current | ≤1 µA |
| Receiver Input Voltage Tolerance | ±30 V |
| RS-232 Standards | EIA-232-E and V.28 |
| Logic Technology | 5 V CMOS |
| Encapsulado | 24-pin PDIP |
| Tipo de montaje | Through-hole |
| Latch-Up Protection | Latch-up free |
Guía de configuración de pines de ADM237LJN 24-pin pdip
Configuración de pines para ADM237LJN (encapsulado 24-pin pdip). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para ADM237LJN.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ADM237LJN es adecuado para 6 aplicacións: Industrial Serial Control Interfaces, Laboratory Instrument Serial Ports, Point-of-Sale and Peripheral Equipment, Data-Acquisition and Test Systems, Embedded Equipment Service Ports, Legacy Equipment Retrofit.
Industrial Serial Control Interfaces
The ADM237LJN fits industrial controllers that need several RS-232 lines but have only a 5 V logic supply. Its five drivers and three receivers support multiple command, status, and data paths, while the onboard DC-to-DC converters generate approximately ±9 V output swing without external negative rails. The 120 kbps rate is appropriate for conventional supervisory and configuration links rather than high-speed bulk transfer. Designers should allocate the required 1 µF capacitors close to the converter pins and provide cable-side protection when the port connects to external equipment.
Recomendado
Laboratory Instrument Serial Ports
The ADM237LJN is useful in laboratory instruments that expose an RS-232 service or control port while operating from a single 5 V rail. Five driver channels can support multiple control lines and three receiver channels can handle status or command feedback at rates up to 120 kbps. Its ±30 V receiver-input tolerance improves robustness on laboratory benches where connected equipment may produce ground offsets or transient excursions. The through-hole PDIP package also simplifies prototype construction and replacement in service-oriented equipment.
Recomendado
Point-of-Sale and Peripheral Equipment
Point-of-sale terminals and peripheral controllers commonly rely on established RS-232 command links that do not require data rates above 120 kbps. The ADM237LJN provides five drivers and three receivers for multiple peripheral functions while deriving the required bipolar line levels from one 5 V supply. This removes the need for separate ±12 V circuitry and reduces external converter design effort. Firmware should confirm whether each attached peripheral requires a particular handshake signal, and the PCB must preserve the device's converter-capacitor layout for reliable operation.
Recomendado
Data-Acquisition and Test Systems
The ADM237LJN can provide a legacy RS-232 command path in data-acquisition and automated test systems that retain compatibility with older instruments. The 120 kbps maximum rate is sufficient for configuration commands, status reporting, and short measurement transfers, while five transmitter channels can coordinate multiple control lines. A single 5 V supply simplifies the analog and digital power sections of larger instruments. For installation environments with long cables, add appropriate external surge and ESD protection because the receiver's ±30 V tolerance is not a substitute for a designed protection network.
Recomendado
Embedded Equipment Service Ports
The ADM237LJN is appropriate for embedded machinery and appliances that retain an RS-232 service connector for configuration, diagnostics, or firmware recovery. It requires only a 5 V supply and produces approximately ±9 V output swing through onboard converters, allowing service-port functionality to coexist with a compact digital power architecture. The shutdown mode draws 1 µA or less, which can reduce consumption when the interface is intentionally inactive. Firmware and connector wiring must be designed to prevent unwanted transitions during startup, reset, and firmware-update procedures.
Recomendado
Legacy Equipment Retrofit
The ADM237LJN supports retrofit and modernization projects that must preserve an RS-232 interface on older equipment. Its 24-pin PDIP package is useful for repair boards and prototype adapters where surface-mount assembly is less convenient. Five drivers and three receivers cover multiple legacy control and status lines at up to 120 kbps. The interface is bipolar and single-ended, so it cannot be connected to an RS-485 differential bus without additional circuitry. Mechanical retention, connector grounding, and cable shielding should be reviewed alongside the electronic interface.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADM237LJN — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Analog Devices |
| Package | 24-pin PDIP |
| Interface Type | RS-232 |
| Supply Voltage | 5 V |
| Maximum Data Rate | 120 kbps |
| Driver Count | 5 drivers |
| Receiver Count | 3 receivers |
| Generated Output Swing | ±9 V |
| Shutdown Current | ≤1 µA |
| Receiver Input Tolerance | ±30 V |
Diferenciadores clave
- High channel count for a 5 V RS-232 transceiver (frente a ADM232LJN)
- Single-supply bipolar drive capability (frente a Conventional external ±12 V RS-232 interface)
- Improved receiver overstress tolerance (frente a Basic RS-232 receiver implementations)
Notas de diseño
Place the manufacturer's specified 1 µF converter capacitors close to their corresponding ADM237LJN pins and keep the associated charge-pump traces short. Use a low-impedance connection from the device's supply pins to the 5 V rail, and avoid routing converter currents beneath sensitive receiver inputs. Follow the capacitor type and voltage-rating guidance in the manufacturer datasheet because ESR and tolerance can affect converter behavior.
Keep RS-232 driver outputs away from receiver inputs and digital timing nets to reduce capacitive and ground-current coupling. Route the connector side of the interface as an unbalanced network with a defined signal-ground relationship to the logic ground. Where the cable leaves the enclosure, provide appropriately coordinated surge and ESD protection; the advertised ±30 V receiver tolerance should not be treated as a complete cable-protection design.
Do not replace this RS-232 transceiver with a similarly labeled RS-485 or RS-422 device without redesigning the interface. The ADM237LJN provides single-ended bipolar signaling and onboard charge pumps, whereas differential bus devices use different driver and receiver circuits. Also avoid assigning signals from a partial pin listing: use the complete manufacturer pin-description table to identify converter capacitors, shutdown control, driver outputs, and receiver inputs.
Budget the 5 V supply for both normal operation and the current required by the onboard DC-to-DC converters. Decouple the device close to its supply pins and verify startup behavior across the intended supply range, especially when multiple RS-232 ports share the same rail. Although shutdown current is specified at 1 µA or less, the normal operating consumption and external load behavior must be evaluated separately.
Información de cumplimiento
The manufacturer datasheet identifies the device as latch-up free and compliant with EIA-232-E and V.28, but no RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration is established by the available material.