ADS7813PB - 16-Bit 40kHz SAR ADC | Texas Instruments
MPN: ADS7813PB ✓ ActiveADS7813PB Overview
An ADC is an interface device that converts a continuously varying analog voltage into a numerical value for processing by a microcontroller, digital signal processor, or industrial controller. The ADS7813 belongs to the successive-approximation, or SAR, ADC family within the broader data-acquisition and signal-conversion hierarchy. Its sampling architecture is appropriate for industrial measurement, instrumentation, control, and embedded systems that require higher resolution than a conventional 8-bit or 12-bit converter.
Key characteristics include 16-bit resolution, 40 kSPS conversion throughput, ±2.0 LSB maximum integral nonlinearity, and at least 87 dB SINAD. The single +5 V supply simplifies system power planning, while the serial interface reduces the number of data lines required on a circuit board. The converter also uses either an internal or external clock, allowing the system designer to synchronize conversion timing with a local microcontroller or peripheral.
The serial interface can operate with an internal or external clock and is described by Texas Instruments as SPI compatible. The ADS7813PB uses a 0.3-inch 16-pin plastic DIP package, which supports through-hole assembly and prototyping. A maximum conversion time of 20 microseconds establishes the basic acquisition-rate limit before system overhead and conversion-control requirements are considered.
Typical applications include process-control instrumentation, pressure and temperature measurement, laboratory data acquisition, industrial sensor interfaces, and embedded control systems. The 16-bit resolution preserves small changes in analog input, while the 40 kSPS rate is sufficient for many slowly changing sensor signals. It is not intended for high-bandwidth waveform capture requiring substantially higher sampling rates.
Design the input network to keep the analog signal within the converter's permitted input range, and follow the manufacturer datasheet when assigning digital signal timing and grounding. Use a stable reference arrangement, adequate bypass capacitance, and clean layout between the analog input, reference, digital interface, and supply pins. Verify acquisition timing with the external-clock option when deterministic system sampling is required.
Drop-in alternatives for ADS7813PB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ADS7813PB (same form factor and footprint) — differing in Package, Mounting Type, Architecture, Input Type, Operating Temperature Range.
ADS7813PBG4
✅ Drop-In📋 Reference alternative (not in catalog)
ADS7813P
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →ADS7812PB
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ADS7811PB
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ADS7813PB Maximum Ratings & Electrical Characteristics
| ADC Type | Successive Approximation (SAR) |
| Resolution | 16 bit |
| Number of Input Channels | 1 channel |
| Sampling Rate | 40 kSPS |
| Maximum Conversion Time | 20 us |
| Supply Voltage | Single +5 V |
| Integral Nonlinearity | ±2.0 LSB maximum |
| Signal-to-Noise and Distortion | 87 dB minimum |
| Operating Temperature Range | -40°C to +85°C |
| Serial Interface | SPI compatible |
| Clock Source | Internal or external |
| Package | 16-pin PDIP, 0.3 inch |
| Pin Count | 16 pins |
| Mounting Type | Through-hole |
| Technology | CMOS |
| Product Type | Low-power sampling analog-to-digital converter |
ADS7813PB 16-pin pdip, 0.3 inch Pin Configuration Guide
Pin configuration for ADS7813PB (16-pin pdip, 0.3 inch package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for ADS7813PB.
Refer to the datasheet for full pin configuration.
Typical Applications
ADS7813PB is suitable for 6 applications: Industrial Process Measurement, Laboratory Data Acquisition, Precision Sensor Interface, Embedded Control Systems, Automated Test Equipment, Low-Power Monitoring Panel.
Industrial Process Measurement
ADS7813PB fits industrial process measurement because its 16-bit resolution can preserve small voltage changes produced by pressure, level, or temperature sensors. The 40 kSPS conversion rate is more than adequate for process variables that evolve over milliseconds rather than requiring high-speed waveform capture. Place the converter between the conditioned sensor signal and a controller, using a stable reference and a single +5 V analog supply. Compared with an 8-bit or 12-bit converter, the 16-bit result offers four additional bits of resolution and can reduce quantization uncertainty by a factor of 16. The -40°C to +85°C operating range also supports equipment deployed across industrial temperature zones.
Recommended
Laboratory Data Acquisition
For laboratory instrumentation, ADS7813PB provides a useful balance between resolution, throughput, and interface simplicity. A 16-bit result supports precise recording of slowly varying or moderate-bandwidth analog signals, while the 40 kSPS rate permits repeated acquisition faster than the stated 20 us maximum conversion time. Its SPI-compatible serial interface reduces the number of wiring connections and can synchronize with an external clock when deterministic acquisition timing is important. Use a low-noise reference and careful grounding to ensure that system accuracy is not limited by the analog front end or reference network.
Recommended
Precision Sensor Interface
ADS7813PB is suitable for conditioning and digitizing outputs from slow, high-resolution sensors such as strain, pressure, and temperature elements. The converter's 16-bit resolution captures changes that may occupy only a small portion of the full-scale input range, while its 40 kSPS throughput supports periodic polling without requiring a high-speed ADC. Implement the sensor, analog filter, ADC, and digital controller on the same measurement board to minimize interference. Pay particular attention to reference stability, input settling, and separating analog return paths from digital clock and serial-data traces.
Recommended
Embedded Control Systems
ADS7813PB can serve as the measurement front end in an embedded controller that needs more analog resolution than a typical low-cost converter. Its single +5 V supply simplifies integration with digital control circuitry, and the flexible SPI-compatible interface can use an internal or external clock to coordinate acquisition with control software. The 16-bit output provides fine numerical granularity for closed-loop adjustments, while 40 kSPS is suitable for many supervisory and slow-loop feedback functions. Validate digital timing, settling behavior, and reference accuracy in the final controller board because firmware configuration and PCB routing materially affect realized performance.
Recommended
Automated Test Equipment
ADS7813PB can serve as the sampling element in automated test equipment that measures modest analog outputs with useful numeric granularity. Its 16-bit resolution improves the visibility of small deviations from a nominal value, and the 40 kSPS rate supports rapid repeated measurements when the test does not demand high-frequency sampling. The serial interface reduces board-space requirements compared with a parallel-output converter. For production-test accuracy, use the external-clock mode where deterministic start timing is required, and ensure the reference remains stable between measurements. Board-level calibration should account for offset, gain, and noise at the operating temperature.
Recommended
Low-Power Monitoring Panel
ADS7813PB works in monitoring panels where multiple analog channels are sampled sequentially under centralized control. Although it has one analog input, its 40 kSPS conversion rate allows one multiplexed input to be updated much faster than many temperature, voltage, or status signals change. The 16-bit resolution can improve display and thresholding precision, while the single +5 V supply supports compact embedded designs. Use the external-clock capability when multiple monitored values must be acquired on a predictable schedule. Pay attention to channel-switching transients, input settling time, and return-current paths to prevent neighboring channels from introducing errors.
Recommended
Recommended Products Summary
Engineering reference data for ADS7813PB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ADS7813PBG4 | ADS7813P | ADS7812PB | ADS7811PB |
|---|---|---|---|---|---|
| Package | PDIP-16, 0.3 inch | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Key Differentiators
- Higher conversion resolution within the same ADS7813 family (vs ADS7812PB)
- Direct same-package family configuration (vs ADS7813PBG4)
- Single +5 V operation with a flexible serial interface (vs ADS7811PB)
Design Notes
Route the analog input and reference connections away from serial clock, chip-select, and digital return paths. Keep the analog and digital grounds connected according to the manufacturer datasheet's recommended grounding scheme, and place bypass capacitors close to their associated supply pins. For a mixed-signal board, minimize copper area under high-impedance input and reference nets to reduce parasitic pickup and sensitivity to adjacent switching signals.
Use the external-clock mode when conversion start timing must be deterministic across acquisition cycles. Confirm setup and hold timing for CS, SCLK, SDI, and SDO from the manufacturer timing diagrams. If the controller and ADC share a ground reference through a cable or backplane, account for ground offset in the analog input range and avoid routing clock returns through sensitive input regions.
Do not assume that a 16-bit data width guarantees 16-bit usable measurement accuracy. The overall error also depends on the reference voltage, analog front-end noise, input settling, PCB contamination, and the conversion timing relative to the sample-and-hold interval. Verify the reference configuration and acquisition sequence in the manufacturer datasheet, and avoid changing the input range or switching network without repeating calibration and settling tests.
Estimated: a 40 kSPS conversion rate produces up to 40,000 conversions per second, but converter power cannot be calculated from that rate alone without the operating current. Measure current at the actual +5 V supply under the chosen clocking and conversion duty cycle. Use the manufacturer operating-current specification and application information to select bypass capacitance and ensure that the supply can support transient demand without disturbing adjacent analog circuitry.
Compliance Information
The manufacturer product page and cited snippets do not state the requested compliance details. AEC-Q100 status is recorded as not_applicable because this ordering code is not identified as an automotive-qualified variant.