ADS7820PB - 12-Bit 100 kSPS Parallel SAR ADC | Texas Instruments
MPN: ADS7820PB ✓ ActiveADS7820PB Overview
An ADC converts a continuous analog voltage into a numeric code for processing, measurement, or control. Within the broader converter hierarchy, the ADS7820PB is a successive-approximation register ADC: an internal sample-and-hold circuit acquires the input, and successive comparison cycles resolve 12 bits. Its parallel output interface places the converted word directly on digital bus pins, which can shorten the path between conversion and a digital bus or microcontroller read cycle compared with serial-output converters.
Key performance characteristics include a 10 us conversion time, 72 dB minimum SINAD with a 45 kHz input, and maximum integral and differential nonlinearity of ±1/2 LSB. The 0 V to +5 V input range directly supports systems operating from a +5 V supply. Internal or external reference selection allows the converter to use its own reference or a precision external voltage when calibration, reference stability, or analog scaling requirements justify an external network.
The CMOS implementation and single-channel architecture suit industrial instrumentation, process measurement, sensor conditioning, laboratory equipment, and embedded data-acquisition systems where deterministic conversion timing and parallel data capture are valuable. The 28-pin PDIP package also simplifies through-hole prototyping and instrument-panel or legacy industrial board construction.
Design care is required around the analog input path. Keep the sampling network close to the analog pins, provide a low-noise reference, and observe the manufacturer layout guidance for grounding and bypassing. The parallel output bus must also be properly terminated or buffered when connected to a processor with a slower or incompatible input impedance.
This page consolidates the device specifications, pin-compatible alternatives, application guidance, and practical design notes into one engineering reference. It highlights where the ADS7820PB fits well and where newer converter families may offer higher throughput, lower power, or serial-interface flexibility.
Drop-in alternatives for ADS7820PB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ADS7820PB (same form factor and footprint) — differing in Package, Resolution, Differential Nonlinearity, Input Type, Integral Nonlinearity.
ADS7821PB
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ADS7822PBG4
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →ADS7823PB
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ADS7824PB
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →ADS7825PB
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →ADS7820PB Maximum Ratings & Electrical Characteristics
| Converter Type | 12-bit successive-approximation ADC |
| Resolution | 12 bit |
| Number of Channels | 1 channel |
| Sampling Rate | 100 kSPS minimum |
| Conversion Time | 10 us |
| Analog Input Range | 0 V to +5 V |
| Supply Voltage | Single +5 V |
| Output Interface | Parallel word access |
| Signal-to-Noise and Distortion | 72 dB minimum with 45 kHz input |
| Integral Nonlinearity | ±1/2 LSB maximum |
| Differential Nonlinearity | ±1/2 LSB maximum |
| Reference | Internal or external |
| Process Technology | CMOS |
| Package | 28-pin PDIP |
| Mounting Type | Through-hole |
| Temperature Grade | Industrial |
| Input Type | Single-ended analog input |
| RoHS Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
ADS7820PB 28-pin pdip Pin Configuration Guide
Pin configuration for ADS7820PB (28-pin pdip package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for ADS7820PB.
Refer to the datasheet for full pin configuration.
Typical Applications
ADS7820PB is suitable for 6 applications: Industrial Process Monitoring, Precision Sensor Signal Conditioning, Laboratory Data Acquisition, Embedded Control and Instrumentation, Audio and Communications Level Monitoring, Legacy Through-Hole Board Upgrade.
Industrial Process Monitoring
The ADS7820PB fits industrial process-monitoring modules that measure a scaled 0 V to +5 V pressure, temperature, or level signal. Its 12-bit resolution supplies 4096 codes, while the 100 kSPS minimum sampling rate supports substantially faster updates than typical slow process loops. Place the device behind a protected, low-impedance analog conditioning stage, and use the single +5 V supply and internal or external reference flexibility to simplify system design. The parallel output allows the measured code to enter a digital bus or capture latch without a serial-conversion stage. Layout should keep the analog input short and place bypass capacitors close to the supply and reference pins.
Recommended
Precision Sensor Signal Conditioning
The ADS7820PB is suitable for digitizing sensor outputs already scaled into the 0 V to +5 V input range. Its 12-bit resolution and ±1/2 LSB maximum nonlinearity provide a useful balance between measurement detail and interface simplicity in instrumentation modules. The converter performs a 10 us conversion, allowing multiple readings during a short observation interval. Use a front-end amplifier or passive divider with an acquisition network designed to settle within the sampling interval. A stable internal reference is suitable for ordinary measurements, while an external reference can improve traceability when calibrated against a precision voltage source.
Recommended
Laboratory Data Acquisition
The ADS7820PB can serve as the analog front end in a laboratory instrument that records low-frequency waveforms or transient measurements. A 12-bit code and 100 kSPS minimum sampling rate provide enough resolution for many instrumentation and control experiments, while the parallel interface permits direct capture by digital logic or a microprocessor. The single-channel design avoids unnecessary multiplexing complexity for single-sensor benches. Place the input driver close to the converter, use shielded routing where appropriate, and include calibration points for gain and offset correction. Verify the acquisition-network settling requirement against the 10 us conversion time in the manufacturer datasheet.
Recommended
Embedded Control and Instrumentation
The ADS7820PB fits embedded controllers that need a dedicated external ADC for analog feedback rather than a multiplexer-rich converter with serial output. Its parallel data bus can connect to a processor through suitable bus drivers or input isolation, and the 12-bit code preserves more detail than an 8-bit converter. The single +5 V analog supply and selectable reference support compact single-board designs. Because the parallel bus exposes multiple high-speed digital nodes, keep traces short, maintain a defined return path, and account for bus loading in the timing design. Use the manufacturer pin-description and layout guidance when assigning control and data lines.
Recommended
Audio and Communications Level Monitoring
The ADS7820PB can be applied to audio, communications, or communications-equipment level monitoring when the signal is conditioned into the 0 V to +5 V range. Its 72 dB minimum SINAD with a 45 kHz input provides adequate dynamic range for amplitude measurement, calibration loops, and supervisory diagnostics. The 100 kSPS sampling capability supports faster monitoring than many slow control systems, although it is not intended to replace a high-rate audio codec. Use anti-alias filtering before the input and separate noisy digital return current from the analog reference path to avoid degrading the measured code.
Recommended
Legacy Through-Hole Board Upgrade
The ADS7820PB is a practical option when maintaining or replicating a through-hole industrial board that uses a 28-pin parallel ADC footprint. Its PDIP construction supports conventional insertion, prototyping, and repair workflows, while the 12-bit resolution and 10 us conversion time cover many legacy measurement channels. A redesign can move to a newer converter if throughput or power becomes critical, but the replacement must be checked for exact pin functions, acquisition timing, reference behavior, and package availability. For a like-for-like maintenance build, preserve the original bypass and reference layout unless the revised datasheet specifies otherwise.
Recommended
Recommended Products Summary
Engineering reference data for ADS7820PB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ADS7821PB | ADS7822PB | ADS7823PB | ADS7824PB | ADS7825PB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-28 | PDIP-28 | PDIP-28 | PDIP-28 | PDIP-28 | PDIP-28 |
Key Differentiators
- Established single-channel parallel acquisition format (vs ADS7821PB)
- Documented pin compatibility with the ADS7821 family (vs ADS7822PB)
- Higher sampling capability for modernized designs (vs ADS7820PB)
- Through-hole 28-pin package supports legacy board maintenance (vs ADS7825U/1K)
Design Notes
Keep the analog input trace short and place its sampling or filtering capacitor close to the converter. Route the analog input away from the parallel data bus and switching-node areas, and provide a quiet return path for the analog ground. The acquisition source must settle within the conversion interval, so include the source impedance and capacitor charging current when checking the datasheet acquisition requirements.
Place the manufacturer-recommended supply-bypass capacitors at the device power pins and keep the +5 V feed short. The converter supports internal or external reference selection, so confirm which reference mode the design uses and follow the specified reference bypass network in either case. Avoid routing reference current through the analog input return, since shared impedance can convert converter activity into measurement error.
The 12-bit parallel bus creates many simultaneous digital transitions that can couple into the analog input. Keep output routing compact, provide a continuous ground reference beneath the bus where practical, and connect the data bus to the receiving logic only when its input characteristics support the loading. If the receiving processor has slow or high-impedance inputs, use suitable bus buffers rather than relying on direct fan-out.
Do not treat a pin-compatible family member as automatically interchangeable. Verify control-pin polarity, conversion timing, output coding, reference implementation, acquisition behavior, and the exact package outline before substitution. The ADS8504 and ADS8505 are identified by the manufacturer as faster pin-compatible alternatives, but their system-level requirements should be reviewed before using them in an ADS7820PB-based design.
Compliance Information
The PB ordering code is associated with a lead-free package designation, but explicit RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status was not stated in the available product information. Industrial temperature grade is identified for this ordering code.