ADS7820PB - 12-Bit 100 kSPS Parallel SAR ADC | Texas Instruments
MPN: ADS7820PB ✓ NakahandaADS7820PB Ulas
An ADC converts a continuous analog voltage into a numeric code for processing, measurement, or control. Within the broader converter hierarchy, the ADS7820PB is a successive-approximation register ADC: an internal sample-and-hold circuit acquires the input, and successive comparison cycles resolve 12 bits. Its parallel output interface places the converted word directly on digital bus pins, which can shorten the path between conversion and a digital bus or microcontroller read cycle compared with serial-output converters.
Key performance characteristics include a 10 us conversion time, 72 dB minimum SINAD with a 45 kHz input, and maximum integral and differential nonlinearity of ±1/2 LSB. The 0 V to +5 V input range directly supports systems operating from a +5 V supply. Internal or external reference selection allows the converter to use its own reference or a precision external voltage when calibration, reference stability, or analog scaling requirements justify an external network.
The CMOS implementation and single-channel architecture suit industrial instrumentation, process measurement, sensor conditioning, laboratory equipment, and embedded data-acquisition systems where deterministic conversion timing and parallel data capture are valuable. The 28-pin PDIP package also simplifies through-hole prototyping and instrument-panel or legacy industrial board construction.
Design care is required around the analog input path. Keep the sampling network close to the analog pins, provide a low-noise reference, and observe the manufacturer layout guidance for grounding and bypassing. The parallel output bus must also be properly terminated or buffered when connected to a processor with a slower or incompatible input impedance.
This page consolidates the device specifications, pin-compatible alternatives, application guidance, and practical design notes into one engineering reference. It highlights where the ADS7820PB fits well and where newer converter families may offer higher throughput, lower power, or serial-interface flexibility.
Mga alternatibo na pwedeng ilagay na ADS7820PB — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ADS7820PB (parehas na form factor at footprint) — pagkakaiba sa Package, Resolution, Differential Nonlinearity, Input Type, Integral Nonlinearity.
ADS7821PB
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
ADS7822PBG4
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →ADS7823PB
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
ADS7824PB
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →ADS7825PB
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →ADS7820PB Mga Pinakamataas na Rating at Electrical Characteristics
| Converter Type | 12-bit successive-approximation ADC |
| Pangangasiwaan | 12 bit |
| Number of Channels | 1 channel |
| Rate ng Pagkupita | 100 kSPS minimum |
| Conversion Time | 10 us |
| Analog Input Range | 0 V to +5 V |
| Volte ng Pagbibigay | Single +5 V |
| Output Interface | Parallel word access |
| Signal-to-Noise and Distortion | 72 dB minimum with 45 kHz input |
| Integral Nonlinearity | ±1/2 LSB maximum |
| Differential Nonlinearity | ±1/2 LSB maximum |
| Reference | Internal or external |
| Process Technology | CMOS |
| Packhaging | 28-pin PDIP |
| Uri ng Pagpapasok | Through-hole |
| Temperature Grade | Industrial |
| Input Type | Single-ended analog input |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Gabay sa Pin Configuration ng ADS7820PB 28-pin pdip
Pin configuration para sa ADS7820PB (28-pin pdip package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa ADS7820PB.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ADS7820PB ay nararapat para sa 6 aplikasyons: Industrial Process Monitoring, Precision Sensor Signal Conditioning, Laboratory Data Acquisition, Embedded Control and Instrumentation, Audio and Communications Level Monitoring, Legacy Through-Hole Board Upgrade.
Industrial Process Monitoring
The ADS7820PB fits industrial process-monitoring modules that measure a scaled 0 V to +5 V pressure, temperature, or level signal. Its 12-bit resolution supplies 4096 codes, while the 100 kSPS minimum sampling rate supports substantially faster updates than typical slow process loops. Place the device behind a protected, low-impedance analog conditioning stage, and use the single +5 V supply and internal or external reference flexibility to simplify system design. The parallel output allows the measured code to enter a digital bus or capture latch without a serial-conversion stage. Layout should keep the analog input short and place bypass capacitors close to the supply and reference pins.
Inirekomenda
Precision Sensor Signal Conditioning
The ADS7820PB is suitable for digitizing sensor outputs already scaled into the 0 V to +5 V input range. Its 12-bit resolution and ±1/2 LSB maximum nonlinearity provide a useful balance between measurement detail and interface simplicity in instrumentation modules. The converter performs a 10 us conversion, allowing multiple readings during a short observation interval. Use a front-end amplifier or passive divider with an acquisition network designed to settle within the sampling interval. A stable internal reference is suitable for ordinary measurements, while an external reference can improve traceability when calibrated against a precision voltage source.
Inirekomenda
Laboratory Data Acquisition
The ADS7820PB can serve as the analog front end in a laboratory instrument that records low-frequency waveforms or transient measurements. A 12-bit code and 100 kSPS minimum sampling rate provide enough resolution for many instrumentation and control experiments, while the parallel interface permits direct capture by digital logic or a microprocessor. The single-channel design avoids unnecessary multiplexing complexity for single-sensor benches. Place the input driver close to the converter, use shielded routing where appropriate, and include calibration points for gain and offset correction. Verify the acquisition-network settling requirement against the 10 us conversion time in the manufacturer datasheet.
Inirekomenda
Embedded Control and Instrumentation
The ADS7820PB fits embedded controllers that need a dedicated external ADC for analog feedback rather than a multiplexer-rich converter with serial output. Its parallel data bus can connect to a processor through suitable bus drivers or input isolation, and the 12-bit code preserves more detail than an 8-bit converter. The single +5 V analog supply and selectable reference support compact single-board designs. Because the parallel bus exposes multiple high-speed digital nodes, keep traces short, maintain a defined return path, and account for bus loading in the timing design. Use the manufacturer pin-description and layout guidance when assigning control and data lines.
Inirekomenda
Audio and Communications Level Monitoring
The ADS7820PB can be applied to audio, communications, or communications-equipment level monitoring when the signal is conditioned into the 0 V to +5 V range. Its 72 dB minimum SINAD with a 45 kHz input provides adequate dynamic range for amplitude measurement, calibration loops, and supervisory diagnostics. The 100 kSPS sampling capability supports faster monitoring than many slow control systems, although it is not intended to replace a high-rate audio codec. Use anti-alias filtering before the input and separate noisy digital return current from the analog reference path to avoid degrading the measured code.
Inirekomenda
Legacy Through-Hole Board Upgrade
The ADS7820PB is a practical option when maintaining or replicating a through-hole industrial board that uses a 28-pin parallel ADC footprint. Its PDIP construction supports conventional insertion, prototyping, and repair workflows, while the 12-bit resolution and 10 us conversion time cover many legacy measurement channels. A redesign can move to a newer converter if throughput or power becomes critical, but the replacement must be checked for exact pin functions, acquisition timing, reference behavior, and package availability. For a like-for-like maintenance build, preserve the original bypass and reference layout unless the revised datasheet specifies otherwise.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ADS7820PB — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ADS7821PB | ADS7822PB | ADS7823PB | ADS7824PB | ADS7825PB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-28 | PDIP-28 | PDIP-28 | PDIP-28 | PDIP-28 | PDIP-28 |
Pangunahing mga Pagkakaiba
- Established single-channel parallel acquisition format (kumpara saADS7821PB)
- Documented pin compatibility with the ADS7821 family (kumpara saADS7822PB)
- Higher sampling capability for modernized designs (kumpara saADS7820PB)
- Through-hole 28-pin package supports legacy board maintenance (kumpara saADS7825U/1K)
Talaan ng Disenyo
Keep the analog input trace short and place its sampling or filtering capacitor close to the converter. Route the analog input away from the parallel data bus and switching-node areas, and provide a quiet return path for the analog ground. The acquisition source must settle within the conversion interval, so include the source impedance and capacitor charging current when checking the datasheet acquisition requirements.
Place the manufacturer-recommended supply-bypass capacitors at the device power pins and keep the +5 V feed short. The converter supports internal or external reference selection, so confirm which reference mode the design uses and follow the specified reference bypass network in either case. Avoid routing reference current through the analog input return, since shared impedance can convert converter activity into measurement error.
The 12-bit parallel bus creates many simultaneous digital transitions that can couple into the analog input. Keep output routing compact, provide a continuous ground reference beneath the bus where practical, and connect the data bus to the receiving logic only when its input characteristics support the loading. If the receiving processor has slow or high-impedance inputs, use suitable bus buffers rather than relying on direct fan-out.
Do not treat a pin-compatible family member as automatically interchangeable. Verify control-pin polarity, conversion timing, output coding, reference implementation, acquisition behavior, and the exact package outline before substitution. The ADS8504 and ADS8505 are identified by the manufacturer as faster pin-compatible alternatives, but their system-level requirements should be reviewed before using them in an ADS7820PB-based design.
Impormasyon ng Pagsunod sa Kautusan
The PB ordering code is associated with a lead-free package designation, but explicit RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status was not stated in the available product information. Industrial temperature grade is identified for this ordering code.