AKM (Asahi Kasei Microdevices)

AK4420VT 24-Bit 192kHz Stereo DAC | Asahi Kasei

MPN: AK4420VT ✓ Active
16-pin TSSOP Package
MOQ: 1 |

AK4420VT Overview

The Asahi Kasei Microdevices AK4420VT is a stereo audio digital-to-analog converter supporting 24-bit digital audio at sampling rates up to 192 kHz and providing a 2 Vrms output. The device accepts I2S-format digital audio and is packaged in a 16-pin TSSOP. Its combination of high-resolution data handling, stereo output capability, and a compact surface-mount package makes it suitable for digital audio equipment, USB audio interfaces, consumer electronics, and compact playback systems.

An audio DAC is the bridge between a digital audio source and an analog output stage. In the signal chain, digital audio data enters the converter, is reconstructed into analog voltage signals, and is then amplified or filtered for loudspeakers, headphones, line inputs, or recording equipment. The AK4420VT operates within the ADC/DAC portion of the broader semiconductor hierarchy, where its primary function is converting 24-bit I2S samples into a stereo analog signal suitable for downstream audio circuitry.

The headline capabilities of the AK4420VT are a 24-bit DAC resolution, operation up to 192 kHz, stereo output, I2S digital audio input, and a 2 Vrms output level. These parameters distinguish it from lower-resolution or lower-bandwidth converters intended for general-purpose or low-cost audio paths. The 192 kHz capability also allows the converter to handle high-rate material associated with studio-quality source material, archival playback, and high-resolution audio equipment when the rest of the signal chain supports those rates.

The AK4420VT is specifically identified as an audio DAC rather than a general-purpose codec. It therefore addresses the conversion stage between a digital audio interface and analog circuitry, without implying that it includes analog-to-digital conversion, microphone preamplification, headphone amplification, or a complete USB interface. System partitioning should preserve those functional boundaries: the AK4420VT can receive digital samples from a USB controller, audio processor, or digital interface, while separate analog stages determine the final output level and load capability.

Typical applications include high-resolution USB audio interfaces, digital audio player boards, compact consumer audio products, line-level stereo conversion, and embedded playback systems. The 16-TSSOP package supports dense surface-mount construction, although analog layout remains critical because the DAC output and digital clock and data connections can affect signal integrity. The manufacturer datasheet should be used to assign every pin and to select the external clock, digital-interface, power, and output-network requirements for the final design.

When designing around the AK4420VT, begin with the complete system signal path rather than the converter in isolation. Confirm that the upstream source supports the intended bit depth and sample rate, that the digital interface format and clocking agree with the device configuration, and that the downstream amplifier can accept the resulting analog output. The principal trade-off is that a compact TSSOP device does not itself provide headphone or speaker drive capability, so a separate output amplifier may be required.

This product data combines the exact manufacturer-related descriptions, interface resolution, maximum sampling rate, output amplitude, and package information with practical selection and integration guidance. It is intended to help engineers identify the correct converter, understand its functional boundaries, and plan a low-noise audio implementation before consulting the full manufacturer datasheet for application-specific details.

Drop-in alternatives for AK4420VT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

No drop-in alternatives available for this product.

Request Alternatives

AK4420VT Maximum Ratings & Electrical Characteristics

Product Type Stereo audio digital-to-analog converter (DAC)
DAC Resolution 24 bit
Maximum Sampling Rate 192 kHz
Digital Audio Interface I2S
Channel Configuration 2-channel stereo
Analog Output Level 2 Vrms
Package 16-pin TSSOP
Mounting Type Surface mount
Digital Input Format I2S
Supported Sample Rates Up to 192 kHz
RoHS Status unknown
REACH Status unknown
Automotive Qualification not_applicable

AK4420VT 16-pin tssop Pin Configuration Guide

Pin configuration for AK4420VT (16-pin tssop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

16-pin tssop package pinout diagram for AK4420VT

No detailed pinout data available for AK4420VT.

Refer to the datasheet for full pin configuration.

Typical Applications

AK4420VT is suitable for 6 applications: High-Resolution USB Audio Interface, 192 kHz High-Resolution Player, Compact Digital Audio Playback Board, Stereo Line-Level Audio Conversion, Consumer Audio Equipment, Digital Recording and Monitoring Path.

🖥️

High-Resolution USB Audio Interface

The AK4420VT fits the stereo DAC stage of a high-resolution USB audio interface because it accepts 24-bit I2S data and supports sampling rates up to 192 kHz. A USB controller can deliver the digital stream and master clock, while the converter produces a 2 Vrms stereo analog output for the interface's line or headphone stage. This partitioning preserves USB protocol handling and analog amplification as separate tasks. Designers should confirm the controller's I2S timing, clock ratio, and supported rate at the selected sample frequency. The AK4420VT does not include a USB controller or headphone amplifier, so those functions require dedicated circuitry and careful analog signal-path design.

🎧

192 kHz High-Resolution Player

The AK4420VT is appropriate for a 192 kHz high-resolution player when the source supplies a compatible 24-bit I2S stream. Its maximum 192 kHz rate allows high-rate PCM data to be converted without reducing the source sampling frequency, while the 2 Vrms output provides a defined line-level target for the following amplifier or filter network. The complete player must still support the operating mode, clocking, and supply requirements specified by the manufacturer. For compact designs, the 16-TSSOP package helps minimize board area, although analog output routing and digital clock isolation remain essential.

📱

Compact Digital Audio Playback Board

The AK4420VT can serve as the central stereo DAC on a compact playback board fed by an embedded processor or digital interface. Its 24-bit resolution, 192 kHz capability, and 2 Vrms output support a high-quality line-level conversion stage within a small system. The device's 16-pin TSSOP package supports standard surface-mount assembly, but board-area savings should not compromise ground partitioning, clock routing, or output filtering. A separate headphone amplifier may be needed for low-impedance loads. The final design should follow the manufacturer datasheet for pin assignment, decoupling, supported digital modes, and output-network requirements.

🔧

Stereo Line-Level Audio Conversion

The AK4420VT is suited to stereo line-level conversion because it produces a 2 Vrms output from a digital I2S source. It can be placed between an audio processor and a balanced or unbalanced line-output stage, depending on the system architecture and the device's specified output configuration. This arrangement is useful when a digital subsystem needs a clean conversion boundary before analog filtering, attenuation, or amplification. Engineering review should verify output topology, allowable load, settling behavior, and bypass requirements from the datasheet. The converter does not itself provide relay switching, gain control, or balanced output amplification.

📺

Consumer Audio Equipment

The AK4420VT can serve as the high-resolution stereo conversion element in consumer audio equipment driven by a digital media processor. Its 24-bit I2S interface and 192 kHz rate support high-resolution playback where the host and storage path support those data rates, while its compact 16-TSSOP package simplifies board integration. A typical design places the DAC near the line-output amplifier and analog output network to minimize sensitive routing. Product engineers should account for startup, power-supply cleanliness, ground returns, and EMI containment. The AK4420VT performs conversion only; volume control, loudspeaker drive, and user-interface functions belong elsewhere in the system.

🎙️

Digital Recording and Monitoring Path

The AK4420VT can support a digital recording or monitoring path when playback-side conversion is required for reference listening or analog capture. A digital audio processor feeds 24-bit I2S samples up to 192 kHz to the converter, and the 2 Vrms stereo output provides the signal for a line monitor, calibrated monitoring amplifier, or subsequent recording stage. This use requires the converter and destination to share the correct sample rate and clock relationship. Engineers must also evaluate grounding and isolation to prevent output converter activity from contaminating sensitive measurement channels. The device does not replace a dedicated ADC for analog recording.

What are the key specifications of AK4420VT that engineers should know?
The AK4420VT is a 24-bit stereo audio DAC with I2S input, operation up to 192 kHz, a 2 Vrms analog output, and a 16-pin TSSOP package. According to the AK4420VT manufacturer datasheet, it is designed for high-resolution digital-to-analog conversion rather than complete audio codec or headphone-amplifier integration. The 192 kHz rate and 24-bit format are the principal selection criteria for high-rate source material.
What is the operating voltage of AK4420VT?
The AK4420VT operating-voltage limits are not stated in the available product descriptions, so the manufacturer datasheet should be consulted before assigning the analog and digital supply rails. The device is identified as a 24-bit stereo DAC operating up to 192 kHz in a 16-pin TSSOP. Use the datasheet power-supply table to confirm voltage, sequencing, and decoupling requirements rather than inferring them from the I2S interface.
Does AK4420VT support 192 kHz and 24-bit audio?
Yes, the AK4420VT supports 24-bit digital audio at sampling rates up to 192 kHz. The manufacturer describes it as a 192 kHz, 24-bit stereo sigma-delta DAC with I2S input. The upstream processor, interface controller, and clocking arrangement must also support the selected rate, because the converter cannot recover source data that is absent from the digital stream.
What audio interface does AK4420VT use?
The AK4420VT uses I2S for its digital audio input. Its listed digital interface, 24-bit resolution, and maximum 192 kHz sample rate make it suitable for systems that already generate a compatible I2S stream. The manufacturer datasheet defines the clock relationship, data timing, and supported operating modes, which should be followed during PCB and firmware design.
Where can I download the AK4420VT datasheet PDF?
The AK4420VT datasheet PDF is available from the Asahi Kasei Microsystems AK4420VT datasheet listing and the linked manufacturer documentation mirror. It contains the detailed electrical characteristics, application information, pin description, and interface timing needed for implementation. Review the document identified as the AK4420VT datasheet rather than relying on a similarly named DAC with a different package.
Where can I find the AK4420VT pinout?
The AK4420VT pinout is defined in the pin-description section of the manufacturer datasheet for the 16-pin TSSOP package. Use that table when assigning analog outputs, digital audio inputs, clock signals, power connections, and ground pins. Because the package uses a compact 16-pin TSSOP, preserve the manufacturer pin numbering and verify every net against the datasheet before fabrication.
What can replace the AK4420VT on the same PCB?
No drop-in replacement is established by the available cross-reference results for the exact AK4420VT configuration. A valid replacement must match the 16-TSSOP footprint, pin assignment, digital interface, resolution, sample rate, supply arrangement, and analog output specifications. The cross-reference tools returned generic lookup pages and related AKM devices rather than a confirmed pin-compatible substitute, so no unverified replacement should be installed.
Is AK4420VT the same as AK4420ET or AK4426VT?
No, those related AKM part numbers cannot be assumed to be interchangeable with AK4420VT. The AK4420VT is specifically identified as a 24-bit, 192 kHz stereo DAC in a 16-TSSOP package, while the comparison search identifies AK4420ET and AK4426VT as related devices without confirming identical packages or pin assignments. Treat them as redesign candidates until their datasheets demonstrate exact footprint and pin compatibility.
When should I choose AK4420VT over a lower-rate audio DAC?
Choose the AK4420VT when the source and system clocking support high-resolution playback up to 192 kHz and a 24-bit I2S stream. Its 2 Vrms stereo output specification also makes it relevant to line-level conversion designs. A lower-rate DAC may be preferable for a source limited to conventional CD rates, but the entire digital path must match the selected format and sample rate.
Is AK4420VT suitable for a USB audio interface?
The AK4420VT is suitable for the DAC stage of a high-resolution USB audio interface when the USB controller supplies compatible I2S data and clocking. Its 24-bit resolution and 192 kHz maximum rate support high-rate digital audio, while the 2 Vrms output can feed an appropriate line-level or downstream amplifier stage. USB protocol handling and analog amplification remain separate functions.
Does AK4420VT include a headphone amplifier?
No, the AK4420VT is identified as a dedicated stereo DAC and does not claim integrated headphone-drive or speaker-drive capability. Its 2 Vrms output must be evaluated against the intended load and amplifier topology. Headphone or speaker systems normally require a separate output amplifier selected for impedance, current, distortion, and power requirements.
How should the AK4420VT be used in a line-level audio product?
Use the AK4420VT as the conversion stage after an I2S-compatible digital audio source and before the product's line output amplifier or filter network. The converter handles 24-bit samples up to 192 kHz and produces a nominal 2 Vrms stereo analog signal. The downstream stage should preserve signal integrity, observe the specified load requirements, and provide any gain, muting, or headphone-drive function required by the product.
Where can I buy AK4420VT online?
Use the Request a Quote form on this page to request AK4420VT availability, current unit pricing, quantity breaks, and lead time from XAIPART. The exact AK4420VT is listed as an in-stock 24-bit, 192 kHz I2S stereo DAC in a 16-TSSOP package. A written quotation is preferable to relying on a changing distributor price or an unconfirmed stock indication.
What is the price of AK4420VT?
The current AK4420VT price is best obtained through the Request a Quote form on this page. The available product listings do not expose a qualifying quantity-break table for the exact part number, so no static unit price is stated here. A quotation can reflect the requested quantity, packaging, delivery location, and current component availability.
What is the lead time and minimum order quantity for AK4420VT?
Request the current lead time, minimum order quantity, and available package configuration through the Request a Quote form on this page. The AK4420VT is actively offered as a 24-bit, 192 kHz I2S stereo DAC in a 16-TSSOP package, but the available listings do not provide a complete manufacturer-backed lead-time schedule. Procurement should use the confirmed quotation for planning purposes.
Is AK4420VT in stock?
AK4420VT is identified as in stock in current product listings, but live inventory and allocation can change quickly. Use the Request a Quote form on this page to obtain the latest availability for the quantity and package you need. Confirm the exact MPN AK4420VT so that similarly named AKM DAC variants are not substituted unintentionally.
How should I compare AK4420VT with AK4426VT?
Compare AK4420VT and AK4426VT by confirming package, pinout, supply voltage, digital interface, resolution, sample rate, clocking, output amplitude, and output topology. The available comparison result establishes that both are related AKM devices but does not establish exact drop-in compatibility. Because AK4420VT is a 16-pin TSSOP device, a footprint match and complete pin-function comparison are required before considering substitution.
What compliance information applies to AK4420VT?
The available product descriptions do not state the RoHS, REACH, lead-free, halogen-free, or conflict-minerals status of the AK4420VT, so those fields remain unknown. The device is not presented as an automotive-qualified component. Request current declarations and material or environmental documentation through XAIPART before using the part in a regulated production program.

Engineering reference data for AK4420VT — comparison, design guidance, and compliance information.

Selection Guide

Choose the AK4420VT when the design requires a dedicated 24-bit stereo DAC with I2S input, operation up to 192 kHz, and a 2 Vrms output in a 16-pin TSSOP. It is well aligned with high-resolution USB audio interfaces, digital playback products, line-conversion modules, and monitoring systems whose upstream controller already produces compatible I2S data and clocks. It is not the best choice when integrated headphone amplification, ADC conversion, USB interface control, or a smaller package is required. The cross-reference results identify related AKM parts but do not establish a pin-compatible substitute, so changing to AK4420ET or AK4426VT should be treated as a redesign until package, pinout, electrical limits, clocking, and output behavior are verified. For production purchasing, use a quotation that confirms the exact MPN, package, current availability, and lead time.

Comparison with Alternatives

Parameter This Product
Brand Asahi Kasei Microdevices
Package 16-TSSOP
Product Type Stereo audio DAC
DAC Resolution 24 bit
Maximum Sampling Rate 192 kHz
Digital Interface I2S
Channel Configuration 2-channel stereo
Analog Output Level 2 Vrms
Integrated Headphone Amplifier No

Design Notes

Place the AK4420VT close to the digital audio source and the first analog output stage so that the sensitive conversion path remains short. Route I2S data and clock signals as controlled-impedance digital nets, and keep analog outputs away from clocks, switching nodes, and inductors. Use a continuous ground reference, minimize loop area, and establish clear digital, analog, and power-supply return paths before assigning the remaining pins from the manufacturer pin-description table.

Design the analog and digital supplies around the manufacturer's voltage, current, sequencing, and decoupling recommendations. Place the required input capacitors and bypass capacitors at the associated device pins, with very short ground returns. Do not infer supply limits from the 24-bit interface or 192 kHz sample rate, because those specifications describe signal resolution and bandwidth rather than the allowed power rails. Verify startup behavior and any analog-output state during initialization before enabling downstream amplifiers.

Treat the I2S data, bit clock, and master-clock connections as a synchronous digital interface and follow the manufacturer timing and clocking configuration. Check setup and hold requirements, output levels, and allowable clock ratios for the selected operating mode. Where the upstream controller and DAC sit on different boards, use a properly terminated or appropriately buffered digital connection rather than relying on a long point-to-point route.

Do not substitute a similarly named AKM DAC without checking the exact package, pinout, clock mode, supply arrangement, and output topology. AK4420ET and AK4426VT appear in related-device comparisons, but the available search results do not establish that either is a 16-TSSOP pin-compatible replacement for AK4420VT. Also remember that a 2 Vrms DAC output does not guarantee safe direct connection to every headphone or speaker load; verify impedance and use a suitable output amplifier when required.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The product descriptions do not state the environmental, material, or automotive-compliance status of the exact AK4420VT. Request current manufacturer declarations before release to production.

Data verified on: 2026-11-11 — data verified and curated by XAIPART's component engineering team

Related Searches

AK4420VT datasheet AK4420VT datasheet pdf AK4420VT pinout AK4420VT specifications AK4420VT 24 bit 192 kHz AK4420VT 2 Vrms output AK4420VT 16-TSSOP AK4420VT I2S DAC AK4420VT equivalent AK4420VT replacement AK4420VT vs AK4426VT AK4420VT application circuit AK4420VT USB audio interface AK4420VT price AK4420VT stock

Related Components & Terms

Asahi Kasei Microdevices AKM AK4420VT AK4420ET AK4426VT stereo DAC digital-to-analog converter audio DAC ADC/DAC semiconductor I2S 24-bit audio 192 kHz sampling rate 2 Vrms output 16-TSSOP TSSOP family surface-mount package USB audio interface high-resolution audio line-level audio digital playback audio monitoring clock jitter power-supply decoupling signal integrity
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details