ATSAMG55J19B-AU - 120MHz Cortex-M4 MCU | Microchip
MPN: ATSAMG55J19B-AU ✓ ActiveATSAMG55J19B-AU Overview
A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile program memory, data memory, and peripherals into one package. The ATSAMG55J19B belongs to the SAM G55 family of embedded microcontrollers. Within the semiconductor hierarchy, it combines an ARM Cortex-M4 processor, real-time embedded control, and low-power system management functions in a single integrated circuit.
The Cortex-M4 processor includes a single-precision floating-point unit, allowing the ATSAMG55J19B to perform floating-point calculations without software emulation. Its 120 MHz maximum clock rate supports responsive control loops, while 512 KB of flash provides program storage for firmware, configuration data, and application logic. The 64-LQFP package provides a conventional leaded surface-mount format that is visually inspectable and suitable for prototype assembly and conventional reflow production.
According to the Microchip product page, the floating-point unit is intended to improve throughput while helping applications reduce active processing time and reach low-power sleep states sooner. This is particularly useful in audio, communications, and industrial equipment where the controller alternates between computation-intensive operations and longer idle intervals. The fixed-function peripherals and memory interfaces are integrated within the SAM G55 architecture rather than requiring separate external logic.
Typical applications include real-time audio and signal processing, industrial control modules, communications equipment, connected embedded products, and low-power sensor nodes. In these systems, the microcontroller can execute control and filtering algorithms, service communication peripherals, and enter sleep modes when workload conditions permit. The 10 mm by 10 mm LQFP-64 footprint also simplifies routing compared with very fine-pitch ball-grid-array packages.
When laying out a board, preserve the manufacturer-defined pin, power, decoupling, and exposed support requirements in the ATSAMG55J19B data sheet. Keep high-current return paths compact, place decoupling capacitance close to the relevant supply pins, and validate signal-integrity and thermal performance on the final PCB. Firmware development should also account for the required clock, reset, boot, and low-power configuration.
This product page consolidates the official device identity, package information, distributor observations, cross-reference candidates, and practical selection guidance into an engineering-focused reference. It also highlights where firmware revision, temperature grade, packaging, and qualification requirements must be checked before treating a related device as a drop-in replacement.
Drop-in alternatives for ATSAMG55J19B-AU — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ATSAMG55J19B-AU (same form factor and footprint) — differing in Package, Core Architecture, Audio Interface, Operating Temperature, USB.
ATSAMG55J19B-AUT
✅ Drop-InContact for price
View Datasheet →ATSAMG55J19A-AU
✅ Drop-InContact for price
View Datasheet →ATSAMG55J19A-AUT
✅ Drop-In📋 Reference alternative (not in catalog)
ATSAMG55J19B-MUT
✅ Drop-InContact for price
View Datasheet →ATSAMG55J19B-MUT
✅ Drop-InContact for price
View Datasheet →ATSAMG55J19B-AU Maximum Ratings & Electrical Characteristics
| Product Type | 32-bit ARM Cortex-M4 microcontroller with FPU |
| Processor Core | ARM Cortex-M4 |
| Architecture | ARM 32-bit |
| Maximum CPU Frequency | 120 MHz |
| Floating-Point Unit | Single-precision FPU |
| Flash Memory | 512 KB (512K x 8) |
| Program Memory Type | Flash |
| Supply Voltage Range | 1.62 V to 3.6 V |
| Package | 64-LQFP, 10 mm x 10 mm |
| Package Height | 1.4 mm maximum |
| Mounting Type | Surface mount |
| Industrial Temperature Grade | Industrial temperature grade |
| Material Compliance | RoHS |
| Order Code | TQFP, MRL B, industrial temperature |
| Shipping Configuration | Tray |
ATSAMG55J19B-AU 1.4 mm maximum Pin Configuration Guide
Pin configuration for ATSAMG55J19B-AU (1.4 mm maximum package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for ATSAMG55J19B-AU.
Refer to the datasheet for full pin configuration.
Typical Applications
ATSAMG55J19B-AU is suitable for 6 applications: Industrial Control Modules, Embedded Audio Processing, Communications Equipment, Low-Power Sensor Nodes, Connected IoT Products, Test and Measurement Instruments.
Industrial Control Modules
The ATSAMG55J19B-AU fits industrial control modules that combine deterministic peripheral handling with higher-level signal processing. Its 120 MHz ARM Cortex-M4 core and integrated single-precision FPU provide computational capacity for control loops, filtering, and state estimation without requiring a separate processor. The 512 KB of flash supports substantial embedded application code, while the 64-LQFP package provides visible joints and a 10 mm by 10 mm footprint for conventional industrial board assembly. Designers should verify the exact peripheral set, operating-temperature requirements, and low-power behavior in the manufacturer datasheet before production release.
Recommended
Embedded Audio Processing
The ATSAMG55J19B-AU is appropriate for embedded audio products that perform real-time filtering, mixing, or control in an MCU rather than a separate DSP. The Cortex-M4 core operates up to 120 MHz, and its single-precision floating-point unit accelerates common audio calculations and reduces the need for software emulation. The 512 KB flash provides room for codecs, control firmware, and audio processing routines. Engineers should confirm interface timing, required sample rates, and peripheral routing in the manufacturer datasheet, then validate latency and audible performance in the complete audio signal chain.
Recommended
Communications Equipment
The ATSAMG55J19B-AU can serve as the control processor in communications equipment where protocol handling, local user-interface logic, and real-time data processing are required. Its 120 MHz Cortex-M4 core supports responsive packet and control processing, while the floating-point unit assists with modulation, filtering, and signal-level calculations. The 512 KB flash capacity accommodates networking stacks and application firmware when configured appropriately. Final qualification should confirm the required serial, Ethernet, USB, or other communication peripherals and verify signal integrity across the complete board rather than relying on headline CPU specifications alone.
Recommended
Low-Power Sensor Nodes
The ATSAMG55J19B-AU suits low-power sensor nodes that alternate between periodic measurements and longer sleep intervals. Microchip specifically describes the Cortex-M4 FPU as helping applications complete active work efficiently and reach sleep faster, which can improve the duty cycle of battery-operated equipment. The device's 1.62 V to 3.6 V operating range accommodates low-voltage system rails, while 512 KB flash supports sensing, communication, and local processing firmware. Designers should select the exact sleep mode, configure unused peripherals correctly, and verify current consumption under realistic sensor and radio activity.
Recommended
Connected IoT Products
The ATSAMG55J19B-AU provides a compact processing platform for connected products that must combine local control, data conditioning, and communications firmware. Its 120 MHz Cortex-M4 performance and 512 KB flash make it useful for gateway-lite, controller, and smart-node designs, while the 64-LQFP package avoids the fine-pitch complexity of larger grid-array devices. The industrial-temperature order designation supports extended-temperature product planning. Before schematic release, confirm connectivity peripherals, antenna and radio integration, boot requirements, regulatory constraints, and the system-level sleep strategy in the target product architecture.
Recommended
Test and Measurement Instruments
The ATSAMG55J19B-AU is appropriate for embedded test and measurement front ends where calibration, sampling control, numerical processing, and user-interface handling are combined in one controller. The single-precision FPU supports calculations involving sensor scaling and digital filtering, while the 120 MHz core can manage multiple real-time tasks. Its 512 KB flash is suitable for instrument firmware, and the 10 mm by 10 mm LQFP package supports conventional inspection after reflow. Accuracy depends on the analog front end, reference source, calibration method, and PCB layout, so validate the complete signal path against the required measurement uncertainty.
Recommended
Recommended Products Summary
Engineering reference data for ATSAMG55J19B-AU — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ATSAMG55J19B-AUT | ATSAMG55J19A-AU | ATSAMG55J19A-AUT | ATSAMG55J19B-MU | ATSAMG55J19B-MUT |
|---|---|---|---|---|---|---|
| Package | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Processor Core | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 |
| Maximum CPU Frequency | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| Order or Revision Code | B-AU | B-AUT | A-AU | A-AUT | B-MU | B-MUT |
Key Differentiators
- Exact B-series identity with the AU order configuration (vs ATSAMG55J19B-AUT)
- Same-package upgrade candidate without changing the CPU or flash allocation (vs ATSAMG55J19A-AU)
- 64-LQFP compatibility across the identified SAM G55 candidates (vs ATSAMG55J19A-AUT)
- Low-risk same-base selection for alternate production handling (vs ATSAMG55J19B-MUT)
Design Notes
Route the ATSAMG55J19B-AU power and ground connections according to the manufacturer recommended layout, placing input and bulk decoupling capacitors close to their associated supply pins. The 64-LQFP package permits visual inspection, but its 0.5 mm lead pitch still requires adequate board density and manufacturing capability. Confirm the courtyard, solder-mask clearance, thermal land recommendations, and exposed support connections in the official package drawing before releasing the PCB footprint.
Design the 1.62 V to 3.6 V supply rail with sequencing, monitoring, and decoupling appropriate to the selected SAM G55 operating mode. The Cortex-M4 can operate at up to 120 MHz, but current demand depends on frequency, active peripherals, and the duty cycle of computation versus sleep. Use the manufacturer operating-current tables for worst-case rail sizing and verify startup and brownout behavior across the complete power-supply tolerance range.
Do not interchange the A and B order or silicon designations solely because ATSAMG55J19A-AU and ATSAMG55J19B-AU share a 64-LQFP footprint and the same 120 MHz, 512 KB headline ratings. Review the manufacturer ordering information, revision notes, errata, and qualification records for the exact assembled device. Likewise, verify whether the intended production flow requires tray handling or the alternate order suffix before approving a purchasing substitution.
Separate sensitive analog or communication paths from switching-converter and high-current return paths even when the microcontroller itself is operating from a low-noise rail. Keep clock, debug, and programming interfaces accessible for production testing, and observe the manufacturer's guidance for unused pins and configuration pins. Validate the final arrangement with signal-integrity and EMC testing because the LQFP package geometry does not eliminate board-level coupling or edge-rate problems.
Compliance Information
The LCSC listing identifies the exact ATSAMG55J19B-AU device as RoHS compliant. Other environmental, automotive-qualification, lead-free, halogen-free, and conflict-minerals statuses are not established by the cited device information.