ATTINY861A-MU - 8-Bit 20MHz AVR MCU | Microchip Technology
MPN: ATTINY861A-MU ✓ ActiveATTINY861A-MU Overview
An 8-bit AVR microcontroller is a compact embedded-processing semiconductor designed to execute control logic efficiently on a single die. The AVR architecture integrates Flash program memory, data EEPROM, SRAM, general-purpose I/O, timers, and communication peripherals into a low-power device. Within the ATtiny product family, the ATTINY861A occupies the middle of the range, combining 8 KB of program storage with a 20 MHz maximum clock rate.
Key features include 8 KB of in-system programmable Flash, 512 bytes of EEPROM, 512 bytes of SRAM, 16 general-purpose I/O lines, and 32 general-purpose working registers. The device also provides an 8-bit timer/counter with compare modes, allowing edge- and pulse-width-related measurements without requiring a separate timer IC. Its compact 32-VQFN package supports dense PCB layouts in consumer, industrial, and IoT control products.
The ATTINY861A-MU uses the Microchip AVR enhanced RISC architecture and is intended for low-power embedded designs where deterministic control, compact code storage, and flexible I/O are more important than high compute throughput. Its 20 MHz operating speed provides adequate timing margin for motor and timer-based control, while the 512-byte SRAM supports modest working memory requirements.
Typical uses include motor-control and fan-speed feedback loops, LED and lighting sequencing, industrial sensing interfaces, small appliance controls, smart-home nodes, and compact metering products. The timer/counter and 16 I/O lines make it particularly suitable for designs combining several digital inputs, pulse outputs, and status indicators in a small board area.
PCB design should preserve access to all power, ground, programming, clock, and I/O lands while keeping switching-current paths compact. Because the package is only 5 x 5 mm, assembly capability, exposed-pad treatment, land pattern tolerances, and soldering-profile control should be reviewed before production release.
This page combines manufacturer specifications, application-focused engineering guidance, package considerations, and drop-in replacement analysis to support faster component selection and PCB implementation. It also identifies where firmware, peripheral, and qualification review remains necessary before treating a substitute as a production equivalent.
Drop-in alternatives for ATTINY861A-MU — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ATTINY861A-MU (same form factor and footprint) — differing in Package, Architecture, SRAM, Flash Memory, Product Type.
ATTINY87-MUR
✅ Drop-InContact for price
View Datasheet →ATMEGA88A-MU
✅ Drop-InContact for price
View Datasheet →ATTINY861A-MU Maximum Ratings & Electrical Characteristics
| Product Type | 8-bit AVR RISC microcontroller |
| Maximum CPU Frequency | 20 MHz |
| Flash Memory | 8 KB (4K x 16) |
| EEPROM Memory | 512 bytes |
| SRAM | 512 bytes |
| General-Purpose I/O Lines | 16 |
| General-Purpose Working Registers | 32 |
| Timer/Counter | 8-bit with compare modes |
| Architecture | AVR enhanced RISC |
| Program Memory Type | In-system programmable Flash |
| Package | 32-VQFN, 5 x 5 mm |
| Mounting Type | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | not_applicable |
ATTINY861A-MU 32-vqfn, 5 x 5 mm Pin Configuration Guide
Pin configuration for ATTINY861A-MU (32-vqfn, 5 x 5 mm package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for ATTINY861A-MU.
Refer to the datasheet for full pin configuration.
Typical Applications
ATTINY861A-MU is suitable for 6 applications: Motor and Fan Speed Control, Industrial Sensing Interface, Smart Home Sensor Node, LED Lighting and Sequencing, Small Appliance Controller, Compact Metering Product.
Motor and Fan Speed Control
The ATTINY861A-MU fits compact motor and fan controllers where an 8-bit timer/counter, 16 general-purpose I/O lines, and 20 MHz processing speed provide adequate control bandwidth without a larger microcontroller. The timer can measure edges or compare pulse widths while the I/O lines operate switches, sensors, and status indicators. The 8 KB Flash stores the control firmware, and 512 bytes of SRAM supports modest run-time state. Designers should confirm the exact PWM and timer resource assigned to the selected pins, provide suitable drive circuitry for the motor, and validate startup, stall, and overcurrent behavior before connecting a load.
Recommended
Industrial Sensing Interface
ATTINY861A-MU is appropriate for compact industrial sensing interfaces that combine digital inputs, timing functions, and local status reporting. Its 16 general-purpose I/O lines can accommodate switches, discrete sensors, and control outputs, while the 8-bit timer/counter assists with pulse and edge measurements. The 512-byte EEPROM is suitable for calibration or configuration storage, and 8 KB of Flash allows firmware to be reprogrammed in-system. In a deployed system, the controller should be reviewed for input filtering, electrical isolation, ESD protection, grounding, and fail-safe output states, since the microcontroller does not replace the required protection and signal-conditioning circuitry.
Recommended
Smart Home Sensor Node
The ATTINY861A-MU can serve as the local controller in a compact smart-home sensor node that monitors switches or digital sensors and drives an indicator or other simple actuator. Its 16 I/O lines provide a practical interface budget, while 8 KB of Flash and 512 bytes of SRAM are sufficient for lightweight event handling and communication support when the communication stack is modest. The 20 MHz clock provides additional timing margin for protocol and debounce routines. Power-budget calculations should include the MCU operating mode, pull-up networks, radio or bus circuitry, and sensor loads. Low-power operation also requires deliberate sleep-mode entry and peripheral shutdown rather than relying on the MCU specification alone.
Recommended
LED Lighting and Sequencing
ATTINY861A-MU is a practical controller for compact LED lighting modules, status indicators, and decorative sequencing systems that require multiple outputs and predictable timing. Its 16 general-purpose I/O lines can drive LED control stages or logic inputs to external drivers, while the 8-bit timer/counter supports timing-related functions. The microcontroller's 8 KB Flash capacity accommodates a dedicated lighting pattern, and the small 5 x 5 mm 32-VQFN package keeps the controller footprint small. Current limiting and transistor or driver selection remain external design responsibilities. Validate thermal performance of the LED stage, provide adequate decoupling, and keep sensitive analog or timing circuits away from high-current switching paths.
Recommended
Small Appliance Controller
ATTINY861A-MU suits small appliance controllers that coordinate buttons, indicators, timers, and simple actuators within a compact board area. The 8-bit AVR core, 8 KB of in-system programmable Flash, and 512 bytes of SRAM are well matched to deterministic embedded-control tasks, while 16 I/O lines support several user inputs and outputs. The timer/counter can assist with elapsed-time measurement or input pulse detection. Production design should address mains isolation, high-voltage switchgear, surge events, brownout behavior, and separation between hazardous and accessible circuitry. Firmware should include safe-state behavior for restart, watchdog expiry, and invalid sensor readings rather than assuming uninterrupted power.
Recommended
Compact Metering Product
ATTINY861A-MU can support a compact metering product that counts pulses, records operating states, and presents local status through indicators or a serial interface. Its timer/counter supports periodic or pulse-related measurement, 512 bytes of EEPROM can retain configuration values, and 8 KB of Flash accommodates a focused metering algorithm. The 32-VQFN package reduces PCB area compared with larger leaded or higher-pin-count devices. Accuracy still depends on the sensing front end, reference components, input filtering, and calibration method. Developers should verify timer tolerance, interrupt latency, data-retention expectations, and the behavior of the external sensor when power is interrupted or reset.
Recommended
Recommended Products Summary
Engineering reference data for ATTINY861A-MU — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ATtiny87-MUR | ATMEGA88A-MU |
|---|---|---|---|
| Package | 32-VQFN, 5 x 5 mm | 32-VQFN | 32-VQFN |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Architecture | 8-bit AVR enhanced RISC | 8-bit AVR | 8-bit AVR |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 8 KB | 8 KB | 8 KB |
| SRAM | 512 bytes | 512 bytes | 512 bytes |
| Mounting Type | Surface mount | Surface mount | Surface mount |
| Programming and Peripheral Compatibility | ATtiny861A device behavior | Requires peripheral and firmware validation | Requires register-map and firmware validation |
Key Differentiators
- Exact ATtiny861A device identity (vs ATtiny87-MUR)
- Compact 20 MHz AVR implementation (vs ATMEGA88A-MU)
- Purpose-built timer and control interface (vs ATtiny87-MUR)
Design Notes
Use the Microchip ATtiny861A package drawing and land-pattern guidance when creating the PCB footprint for the 5 x 5 mm 32-VQFN package. Confirm pad dimensions, exposed-pad geometry, solder-mask clearance, and the manufacturer recommendation for thermal-via placement. Check pin-1 orientation against the centroid marker and keep programming-test pads accessible for production programming and inspection.
Place the decoupling network at the device power pins and connect it with short, low-impedance traces. Follow the voltage and capacitor recommendations in the manufacturer datasheet rather than estimating values from adjacent designs. Account for voltage-dependent current, startup behavior, and external load transients when designing the supply. If the same rail drives motors, relays, or LEDs, use separation and filtering so their switching transients do not couple into the microcontroller supply path.
Treat every assigned I/O pin as a design decision rather than an interchangeable resource. Review the pin-multiplexing table for timer, programming, communication, and reset functions, and avoid placing timing-sensitive signals next to switching nodes. Maintain a continuous ground reference, use appropriate series resistance for exposed signal lines when required, and validate reset, clock, and programming signals at the assembled-board level.
Do not assume that two 32-VQFN AVR devices with 8 KB Flash are firmware-compatible. Before substituting ATtiny87-MUR or ATMEGA88A-MU, compare pin multiplexing, peripheral registers, interrupt vectors, timer channels, analog functions, fuse definitions, and clock behavior. Rebuild and test the firmware, then verify cold start, reset, brownout, watchdog, programming, and worst-case I/O timing on the revised board.
Compliance Information
The Microchip product page identifies the ATtiny861A device family, but specific environmental and material-compliance declarations for ATTINY861A-MU require confirmation from the manufacturer product documentation or declaration.