CD4052BMT - 20V 4:1 Analog Multiplexer | Texas Instruments
MPN: CD4052BMT ✓ ActiveCD4052BMT Overview
An analog multiplexer is a semiconductor switch that connects multiple signal paths to a common output. The CD4052BMT belongs to the analog switch and multiplexer hierarchy, where it can operate as either a multiplexer or a demultiplexer. In multiplexer mode, two select inputs determine which of four channels reaches each common terminal. In demultiplexer mode, one signal can be routed toward selected channel outputs. This makes the device useful for compact analog signal-distribution and selection systems.
The principal features include two 4:1 switching sections, a 20 V signal-handling capability, 240 ohm on-state resistance, and logic-level conversion for the address inputs. The two select inputs allow the device to address four positions across both sections. The 16-SOIC package provides a conventional surface-mount format suitable for industrial, instrumentation, communications, control, and test-and-measurement equipment where analog signals must be selected without introducing an active amplifier stage.
The CD4052B family uses CMOS switching structures to provide low off-state leakage and low quiescent current across the specified supply range. Because the common terminals can serve as inputs or outputs, one package can implement either signal selection or signal distribution without changing the basic PCB footprint. Designers should nevertheless verify signal amplitude, control-logic levels, package pin assignments, and off-state behavior against the manufacturer datasheet before applying the device to a new circuit.
Typical uses include multimeter input selection, sensor-channel multiplexing, control and measurement systems, communications routing, and analog signal conditioning. In a measurement system, the two common terminals can select paired signal groups, while the two address inputs select one of four channels. The 240 ohm on-state resistance is relevant when driving downstream circuitry, and it should be compared with the input impedance and bandwidth requirements of the next stage.
A critical design consideration is the relationship among the analog signal range, supply voltage, and negative supply used by the device. The analog signal must remain within the permitted operating limits, and unused inputs should be connected according to the manufacturer pin-description table. Because the control inputs provide logic-level conversion, their thresholds should be checked against the voltage levels of the controlling microcontroller or logic family.
This product page combines the manufacturer device description with application guidance, pinout-location information, drop-in replacement analysis, and a parameter-by-parameter comparison. It is designed to help engineers identify whether the CD4052BMT fits an existing 16-SOIC design and what must be revalidated when changing suppliers, operating voltage, or control logic.
Drop-in alternatives for CD4052BMT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with CD4052BMT (same form factor and footprint) — differing in Package, Product Type.
CD4052BM
✅ Drop-InContact for price
View Datasheet →MC14052BDG
✅ Drop-In📋 Reference alternative (not in catalog)
TMUX4052
✅ Drop-In📋 Reference alternative (not in catalog)
CD4052BMT Specifications
| Product Type | Dual 4:1 analog multiplexer and demultiplexer |
| Maximum Signal Voltage | 20 V |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | 4:1 |
| On-State Resistance | 240 ohm |
| Logic-Level Conversion | Supported |
| Select Input Count | 2 select inputs |
| Package | 16-SOIC |
| Mounting Type | Surface mount |
| Technology | CMOS |
| Output Configuration | 2-circuit, 4:1 multiplexer or demultiplexer |
CD4052BMT 16-soic Pin Configuration Guide
Pin configuration for CD4052BMT (16-soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for CD4052BMT.
Refer to the datasheet for full pin configuration.
Typical Applications
CD4052BMT is suitable for 6 applications: Multimeter Analog Input Selection, Industrial Sensor Channel Multiplexing, Communications Signal Routing, Test and Measurement Signal Distribution, Analog Control Signal Selection, Data Acquisition Front Ends.
Multimeter Analog Input Selection
The CD4052BMT fits a multimeter or laboratory measurement instrument that must connect one of several sensor or probe outputs to a common measurement amplifier. Its two 4:1 sections can select paired channels with only two address inputs, reducing the number of separate analog switches required. The 240 ohm on-state resistance is acceptable when the following amplifier has sufficiently high input impedance and bandwidth. Because the common terminals can operate as inputs or outputs, the same device can support measurement routing in either multiplexing or demultiplexing arrangements. The 16-SOIC package also simplifies replacement on an existing through-hole-style surface-mount layout.
Recommended
Industrial Sensor Channel Multiplexing
The CD4052BMT is suitable for industrial control boards that must select signals from multiple temperature, pressure, or position sensors. The 20 V signal-handling capability accommodates many externally biased analog sensor outputs, while two 4:1 sections permit selection of two related inputs using a common pair of address lines. The 240 ohm on-resistance should be included in the source impedance calculation for the downstream amplifier or ADC. Logic-level conversion allows the select lines to be driven by a suitable control system, subject to the voltage thresholds and timing limits stated in the datasheet.
Recommended
Communications Signal Routing
The CD4052BMT can route low-frequency analog communications or measurement signals in equipment that requires a compact four-position selector. Two select inputs establish one of four addresses, allowing the same control interface to operate both analog sections. The CMOS architecture and 240 ohm on-state resistance make it useful where a relay-based selector would be larger, slower, or less suitable for low-level signals. Design checks should include off-state isolation, leakage into adjacent channels, allowable input overvoltage, and the bandwidth required by the selected signal path.
Recommended
Test and Measurement Signal Distribution
The CD4052BMT is applicable in test equipment that distributes a common excitation or return signal among four instrument channels. One common terminal can carry the shared signal while the other common terminal provides an alternate routing path, enabling compact multiplexer or demultiplexer arrangements. Its 20 V class is useful for many low-energy measurement systems, while the 16-SOIC package supports automated board assembly. Validate the complete input-output impedance, leakage, settling time, and channel-isolation requirements before using it for precision reference or high-impedance measurements.
Recommended
Analog Control Signal Selection
The CD4052BMT can select control, feedback, or setpoint signals in analog control systems where several sources must reach one processing amplifier. Its dual 4:1 organization supports two selected outputs from one four-position address code, which can simplify coordinated routing of a signal and its associated reference. The 240 ohm switch resistance must be considered alongside amplifier input bias current and cable capacitance. Control logic should remain within the specified thresholds, and external protection may be required if field-connected inputs can experience transients beyond the device's absolute maximum ratings.
Recommended
Data Acquisition Front Ends
The CD4052BMT is useful in data-acquisition front ends that multiplex several analog inputs ahead of an ADC or instrumentation amplifier. Two independent 4:1 sections can organize differential or paired channels while keeping control logic simple. The 240 ohm on-state resistance can create an RC network with source capacitance, so the resulting settling behavior must be checked against the acquisition timing requirement. The 20 V signal class supports many industrial measurement ranges, but the design must still comply with the specified supply voltages, control thresholds, and absolute maximum ratings.
Recommended
Recommended Products Summary
Engineering reference data for CD4052BMT — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | CD4052BM | MC14052BDG | TMUX4052 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | onsemi | Texas Instruments |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Multiplexer Configuration | 4:1 | 4:1 | 4:1 dual multiplexer | 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 channels |
Key Differentiators
- Established dual 4:1 routing in a standard 16-SOIC footprint (vs MC14052BDG)
- Direct same-family option (vs CD4052BM)
- Manufacturer-identified upgrade path (vs TMUX4052)
Design Notes
Verify the exact pin assignments and power connections in the manufacturer datasheet before laying out the PCB. The common terminals can function as inputs or outputs, so reversing the signal direction can change which pins require low-impedance routing and which act as address-controlled channels. Also confirm that every analog signal remains within the permitted input and supply ranges; the 20 V signal-handling rating must not be interpreted as permission to exceed the absolute maximum supply ratings.
Include the 240 ohm on-state resistance in the complete source-impedance budget for the selected channel. Together with connector, PCB, and receiver capacitance, it can create an RC low-pass response and lengthen settling time. For high-impedance sensors or precision measurements, compare the switch resistance with the amplifier input impedance and calculate the allowable settling interval before the next conversion or acquisition.
Route the two select lines as compact, consistently driven digital nets and keep sensitive analog channels away from long switching-current paths. The two multiplexed sections share address information, so adequate drive strength and clean logic levels are essential. Where the analog source is sensitive to charge injection or switching transients, add source impedance, filtering, or a suitable settling period and verify the result with the actual source and receiver impedances.
Compliance Information
Compliance declarations were not identified for the exact CD4052BMT ordering option. AEC-Q100 is treated as not applicable because this is not presented as an automotive-qualified device.