Renesas Electronics

DG406DYZ - 16:1 CMOS Analog Multiplexer | Renesas

MPN: DG406DYZ ✓ Active
100 ohm Rds(on) 28-pin SOIC Package
MOQ: 1 |

DG406DYZ Overview

The Renesas Electronics DG406DYZ is a single 16:1 CMOS analog multiplexer with a 100 ohm on-resistance, housed in a 28-pin SOIC package. It provides sixteen analog switches, TTL- and CMOS-compatible channel decoding, an internal voltage reference for logic thresholds, and an ENABLE input for multiplexing multiple devices. The same architecture can be configured for single-ended 16-channel routing or differential 8-channel routing.

An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a common output. It belongs to the analog switch and multiplexer hierarchy within interface ICs. By translating binary address and enable signals into controlled switch states, a multiplexer's digital control logic can route low-frequency analog signals without requiring a separate analog switch for every connection.

The DG406 family combines a 16-switch array with address-decoding circuitry in one monolithic CMOS device. Its TTL- and CMOS-compatible control inputs simplify interfacing with modern digital systems, while the voltage reference establishes consistent switching thresholds. The ENABLE input allows multiple multiplexers to share address lines and prevents unwanted paths from being connected when the device is disabled.

Renesas describes the DG406 and DG407 as drop-in replacements for the DG506A and DG507A series. That legacy continuity makes the DG406 useful in equipment designed around established 28-pin analog-routing interfaces. The principal design consideration is ensuring that signal amplitude, bandwidth, leakage, charge injection, and switching transients remain acceptable for the source and destination circuitry.

Typical applications include audio signal routing, communication systems, data-acquisition systems, guidance and control systems, sample-and-hold circuits, and test equipment. In a data-acquisition system, the device can route multiple sensor or measurement channels into a shared converter input. In audio equipment, it can select among several signal paths while preserving a common downstream amplifier or converter.

For PCB design, place the device so every selected analog trace remains short and away from high-speed digital and switching-power paths. Confirm input and output voltage limits, supply requirements, and the control-logic truth table in the manufacturer datasheet. Verify the supported switch configuration and signal polarity before finalizing differential routing.

This page organizes the DG406DYZ architecture, verified technical characteristics, same-footprint alternatives, and application-focused design guidance into a concise engineering reference for analog-routing designs.

Drop-in alternatives for DG406DYZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with DG406DYZ (same form factor and footprint) — differing in Package, Logic Threshold Reference, Number of Analog Switches, Number of Channels, Technology.

Analog Devices
Package: 28-pin DIP, 0.600 inch (15.24 mm) pitch
Number of Channels: 16 single-ended or 8 per mux
Technology: CMOS
Compare with DG406DYZ →
Renesas Electronics
Package: 28-pin SOIC (SOIC-28), surface mount
Logic Threshold Reference: Internal voltage reference for logic thresholds
Number of Analog Switches: 16
Compare with DG406DYZ →

DG406DY-T

✅ Drop-In
Renesas Electronics
📦 SOIC-28
1 x 16:1 single-ended or differential 8-channel · 16 switches · Monolithic CMOS · 100 ohm · 28-pin SOIC · Surface mount · TTL- and CMOS-compatible · Internal voltage reference

Contact for price

View Datasheet →

DG406DY

✅ Drop-In
Renesas Electronics
📦 SOIC-28
CMOS analog multiplexer (1 x 16:1 single-ended / 8 x 1:1 differential) · 16 · 16:1 single-ended / 8:1 differential · 100 ohm · ±20 V (34 V total) · TTL and CMOS compatible digital decode · Internal voltage reference for logic thresholds · Yes, for device selection when several multiplexers are present

Contact for price

View Datasheet →

DG406DW-E3

✅ Drop-In
📦 SOIC-28
Same DG406-family 16:1 role and 28-pin SOIC configuration, with 0% channel-count difference; ordering and electrical details require verification.

📋 Reference alternative (not in catalog)

DG406EWI+T

✅ Drop-In
📦 SOIC-28
Same 16:1, 28-pin SOIC configuration with 0% channel-count difference; resistance, leakage, bandwidth, and limit values require datasheet comparison.

📋 Reference alternative (not in catalog)

DG406EWI-T

✅ Drop-In
📦 SOIC-28
Same 16:1, 28-pin SOIC configuration with 0% channel-count difference; temperature grade and detailed electrical limits require verification.

📋 Reference alternative (not in catalog)

DG406DN+T

✅ Drop-In
Analog Devices
📦 SOIC-28
16:1 single-ended analog multiplexer · 16 channels · 4 bits · 100 Ω · 8 Ω · 9 Ω · 1 common output · 28-pin PLCC

Contact for price

View Datasheet →

DG406DYZ Specifications

Multiplexer Configuration Single 16:1 or differential 8:1
Number of Circuits 1 circuit
On-Resistance 100 ohm
Number of Analog Switches 16 switches
Technology Monolithic CMOS
Address Input Compatibility TTL and CMOS compatible
Logic Threshold Reference Internal voltage reference
Enable Control 1 ENABLE input
Number of Pins 28 pins
Package 28-pin SOIC
Mounting Type Surface mount
Operating Temperature Range -40°C to +85°C
Single-Ended Mode 16 channels
Differential Mode 8 channels

DG406DYZ 28-pin soic Pin Configuration Guide

Pin configuration for DG406DYZ (28-pin soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

28-pin soic package pinout diagram for DG406DYZ

No detailed pinout data available for DG406DYZ.

Refer to the datasheet for full pin configuration.

Typical Applications

DG406DYZ is suitable for 6 applications: Data Acquisition Systems, Audio Signal Routing, Sample-and-Hold Circuits, Communication Systems, Guidance and Control Systems, Test and Measurement Equipment.

📊

Data Acquisition Systems

The DG406DYZ is well suited to selecting among multiple analog measurement channels in a data-acquisition system. Its 16-switch array can route one single-ended source at a time or eight differential pairs, reducing the number of external signal paths entering a shared converter. The internal TTL- and CMOS-compatible decoding simplifies address generation, while the ENABLE input permits controlled isolation during reset or calibration. Design the source impedance and acquisition bandwidth around the switch's 100 ohm on-resistance and verify settling, leakage, and charge-injection requirements against the manufacturer datasheet.

🎧

Audio Signal Routing

The DG406DYZ can route audio inputs or test signals through a common amplification and conversion chain. Its single-ended 16-channel configuration offers broad source selection, while differential 8-channel operation can support balanced audio paths. The 100 ohm on-resistance is modest for many line-level signals, although source impedance and the impedance seen by downstream amplifiers still determine practical loading. Use short, shielded analog traces and keep switching nodes away from clock and power-converter paths to reduce audible or measurable crosstalk.

⚡

Sample-and-Hold Circuits

A DG406DYZ can select one of several sampled or sensed signals before feeding a sample-and-hold stage. The 16-switch array provides more channel density than a discrete analog switch network, and the address decoder allows firmware or a control counter to update the selected path. Timing must account for address propagation, switch settling, charge injection, and the acquisition interval. The ENABLE input can hold the multiplexer inactive while the hold circuit acquires, preventing an unintended source from disturbing the sampled node during critical conversion periods.

🌐

Communication Systems

The DG406DYZ can consolidate several low-frequency analog communication paths into a shared receiver or measurement circuit. Its TTL- and CMOS-compatible address decoding supports integration with digital controllers, while the internal logic-threshold reference supports consistent decoding across compatible supply conditions. The ENABLE input is useful when multiple multiplexers share control lines or when the receiver must be isolated during channel changes. Validate signal bandwidth, insertion loss, off-channel isolation, and switch-transient behavior before using it in high-rate or precision communication links.

🏭

Guidance and Control Systems

The DG406DYZ can multiplex feedback, position, or sensor signals into a shared control-processing input. Its 28-pin SOIC implementation and 16-switch array provide a compact way to organize several analog channels while keeping address and enable control in the digital domain. For safety- or mission-critical behavior, verify the exact pinout, power limits, operating temperature range of -40°C to +85°C, and fault behavior for the ordered device. The system should also disable the mux or select a defined fallback path during reset so the control input never floats unexpectedly.

🔧

Test and Measurement Equipment

The DG406DYZ is applicable to test equipment that routes multiple test points, reference levels, or injected signals into a shared measurement chain. Sixteen single-ended inputs or eight differential pairs provide flexibility for automated fixtures. TTL- and CMOS-compatible decoding allows direct control from test sequencers, and the ENABLE input supports isolation between measurements. For precision instruments, characterize leakage, channel resistance, settling time, and crosstalk with the actual source impedance. Layout should preserve short return paths and minimize coupling from adjacent digital control and switching-supply nodes.

Recommended Products Summary

DG406DN+T Analog Devices Used in: Data Acquisition Systems, Audio Signal Routing, Communication Systems, Test and Measurement Equipment DG406EWI+T 28-pin cross-brand multiplexer candidate Used in: Data Acquisition Systems, Sample-and-Hold Circuits DG406EWI-T 28-pin signal-routing candidate Used in: Audio Signal Routing, Guidance and Control Systems DG406DY Renesas Electronics Used in: Sample-and-Hold Circuits, Test and Measurement Equipment DG406DW-E3 Same-family communication-routing candidate Used in: Communication Systems DG406DY-T Same-family control-routing candidate Used in: Guidance and Control Systems
What is the DG406DYZ?
The DG406DYZ is a Renesas Electronics monolithic CMOS analog multiplexer that supports single-ended 16-channel or differential 8-channel routing. According to the manufacturer datasheet, it contains 16 analog switches, TTL- and CMOS-compatible address decoding, an internal voltage reference for logic thresholds, and an ENABLE input. The device is offered in a 28-pin SOIC package and has a stated on-resistance of 100 ohm.
What are the key specifications of DG406DYZ that engineers should know?
The DG406DYZ combines a 16:1 analog-switch configuration with a 28-pin SOIC package and a 100 ohm on-resistance. According to the Renesas Electronics DG406 and DG407 datasheet, it provides TTL- and CMOS-compatible address inputs, an internal threshold voltage reference, and an ENABLE input for controlling multiple multiplexers. Its operating temperature range is -40°C to +85°C, and it can be used in either 16-channel single-ended or 8-channel differential arrangements.
Where can I download the DG406DYZ datasheet PDF?
The official DG406DYZ datasheet is available through the Renesas Electronics DG406 and DG407 datasheet page at https://www.renesas.com/en/document/dst/dg406-dg407-datasheet. The manufacturer document describes the 16-switch array, TTL- and CMOS-compatible decoding circuit, internal logic-threshold reference, ENABLE input, single-ended and differential configurations, and the relationship between DG406 and legacy DG506A devices.
Where can I find the DG406DYZ pinout?
The DG406DYZ pin assignment is documented in the Renesas Electronics DG406 and DG407 manufacturer datasheet. Use the pin-description table and package drawing for the 28-pin SOIC footprint before assigning PCB nets. The product searches identify the device as a 28-pin SOIC analog multiplexer, but a complete numbered pin table is not reproduced on this page to avoid introducing connection errors.
Can DG406DYZ be used for differential signal routing?
Yes, the DG406DYZ can support differential 8-channel routing as well as single-ended 16-channel operation. The manufacturer identifies it as a single 16-channel/differential 8-channel CMOS analog multiplexer. Differential use doubles the number of switch paths consumed relative to single-ended routing, so a 16-channel device is used as eight differential channels. Signal amplitude, common-mode range, and switching behavior must remain within the datasheet limits.
Is DG406DYZ compatible with TTL and CMOS control signals?
The DG406DYZ uses TTL- and CMOS-compatible digital decoding for channel selection. According to the Renesas Electronics manufacturer datasheet, an internal voltage reference defines the logic thresholds, while the address inputs determine which one of the 16 analog switches is connected. This makes the device suitable for systems combining older TTL control logic with CMOS address-generation circuitry, provided the actual supply and input levels satisfy the specified operating conditions.
What is the DG406DYZ ENABLE input used for?
The ENABLE input is used to select whether the DG406DYZ participates in the routed analog path. According to the manufacturer datasheet, this control makes it practical to use several multiplexers in one system while sharing address lines. Holding the device in its disabled state prevents an unintended analog connection. Firmware and hardware should use ENABLE for safe startup, reset, channel-isolation, and fault-recovery sequencing.
Where can I buy DG406DYZ online?
Use the Request a Quote form on this XAIPART page to request DG406DYZ availability, current commercial terms, and suitable packaging for your quantity. The form lets you specify tube, tape-and-reel, or other required delivery format without relying on a static listing. For technical confirmation of the exact MPN and package, include the 28-pin SOIC configuration and your required operating temperature range.
What is the price of DG406DYZ?
Current DG406DYZ commercial pricing is best requested through the Request a Quote form on this page because pricing changes with quantity, availability, and delivery format. The form can capture the quantity breaks required for production planning while keeping the response tied to the exact DG406DYZ ordering code. No static price figure should be used for budgeting because availability and procurement conditions can change.
What is the lead time for DG406DYZ?
Request the current DG406DYZ lead time through the Request a Quote form on this page. Include your required quantity, package-delivery preference, target date, and whether the design allows an alternate manufacturer-approved source. A procurement response is more reliable than a generic catalog estimate because component lead times can vary with inventory, production schedules, and the number of boards being built.
Is DG406DYZ in stock?
Current DG406DYZ inventory status should be confirmed through the Request a Quote form on this XAIPART page. State the quantity, 28-pin SOIC delivery requirement, and target production date so the quotation can reflect the appropriate supply channel. If continuity is critical, ask for a scheduled allocation and an acceptable second-source plan rather than relying only on an immediate stock indication.
DG406DYZ vs DG406DN+T: which is better for a new 16:1 mux design?
DG406DYZ and DG406DN+T are both presented as 28-pin, single 16:1 multiplexers, but DG406DYZ is from Renesas Electronics while DG406DN+T is from Analog Devices. The cross-reference information identifies DG406DN+T as the same functional series with an SOICW package. Final selection should compare supply voltage, on-resistance, leakage, bandwidth, logic levels, temperature rating, lifecycle status, and exact pin behavior in the manufacturer datasheets.
What is the difference between DG406DYZ and DG406EWI+T?
DG406DYZ is a Renesas Electronics 28-pin SOIC device, while DG406EWI+T is a Maxim Integrated 28-pin SOIC device. The published comparison identifies both as surface-mount 28-pin multiplexers, but detailed electrical differences require checking each datasheet. Use DG406DYZ when its Renesas specifications and lifecycle fit the design; consider DG406EWI+T when a documented second source meets the voltage, resistance, leakage, bandwidth, and control requirements.
When should I choose DG406DYZ over DG406DY-T?
Choose DG406DYZ when its stated 100 ohm on-resistance, 28-pin SOIC configuration, and Renesas documentation meet the system requirements. The DG406DY-T appears in cross-reference material as another DG406-family ordering option, so it can be evaluated as a source alternative. The decision should also account for exact package dimensions, pinout, temperature coverage, production status, and manufacturer-specific electrical limits rather than relying on the shared family name alone.
Is DG406DYZ suitable for data acquisition and test equipment?
Yes, the DG406DYZ is specifically suited to data-acquisition systems, sample-and-hold circuits, test equipment, audio routing, communications, and guidance or control systems. Its 16-switch array can route multiple analog sources into a shared signal path, while TTL- and CMOS-compatible decoding simplifies control. Performance depends on source impedance, acquisition bandwidth, settling requirements, leakage, and switch-transient behavior.
What can replace DG406DYZ in a drop-in design?
The documented 28-pin SOIC alternatives include DG406DY-T and DG406DY from Renesas Electronics, plus DG406EWI+T, DG406EWI-T, and DG406DN+T from other manufacturers. These candidates match the target's package count and 16:1 multiplexing role, but each should be checked against the original PCB for exact pinout, enable polarity, supply voltage, logic thresholds, on-resistance, leakage, and bandwidth before substitution.
What is the best cross-brand equivalent for DG406DYZ?
DG406DN+T is a documented cross-brand equivalent candidate because it is described as a 28-pin SOIC, single 16-channel DG406-series multiplexer. It can support a drop-in evaluation where its manufacturer documentation confirms the same pinout and electrical behavior. Pin compatibility alone is not sufficient: verify supply range, switching resistance, leakage, bandwidth, control timing, enable polarity, and temperature limits for the target system.

Engineering reference data for DG406DYZ — comparison, design guidance, and compliance information.

Selection Guide

Choose the DG406DYZ when a design needs a 28-pin SOIC analog multiplexer with 16 single-ended or eight differential channels, a 100 ohm on-resistance, and TTL- or CMOS-compatible address control. It is appropriate for data-acquisition, sample-and-hold, audio-routing, communications, guidance, control, and test-equipment systems whose signal bandwidth and switching requirements fit the DG406 family. Consider DG406DY-T, DG406DY, or DG406DW-E3 when maintaining a Renesas-based source plan and their individual ordering codes meet production requirements. Evaluate DG406EWI+T, DG406EWI-T, or DG406DN+T as cross-brand sourcing options, but do not approve them solely because they use 28 pins. Confirm exact pinout, switched and common terminals, ENABLE polarity, supply range, logic thresholds, on-resistance, leakage, bandwidth, channel isolation, temperature grade, and lifecycle status before replacing the DG406DYZ.

Comparison with Alternatives

Parameter This Product DG406DY-T DG406DY DG406DW-E3 DG406EWI+T DG406EWI-T DG406DN+T
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Maxim Integrated Maxim Integrated Analog Devices
Package SOIC-28 SOIC-28 SOIC-28 SOIC-28 SOIC-28 SOIC-28 SOIC-28
Number of Pins 28 28 28 28 28 28 28

Key Differentiators

  • Combines 16 physical switches with integrated channel decoding (vs DG406DN+T)
  • Supports single-ended and differential routing in one device (vs DG406EWI+T)
  • Compatible with both TTL and CMOS control systems (vs DG406EWI-T)

Design Notes

Treat the selected analog path as a switched 100 ohm resistance when assessing loading. Estimate the divider formed by that resistance and the input impedance of the receiving circuit, then confirm that the resulting attenuation remains acceptable. For high-impedance sensors, include amplifier input capacitance and cable capacitance in settling analysis. Keep the multiplexer output trace short and place any following buffer amplifier close enough to isolate the shared node from downstream loading.

Route each analog input directly to its assigned package pin and avoid crossing the paths with digital address lines, ENABLE, switching regulators, or high-current return paths. Use a continuous ground plane where the layout permits, but return the digital-control ground current directly to the device ground rather than through the analog input area. Separate the shared analog output route from neighboring high-speed nets and provide a nearby return path to minimize loop area and coupling.

Do not assume that the 28-pin package alone guarantees substitution. Verify the complete pin names, ENABLE polarity, address truth table, supply requirements, logic thresholds, input and output voltage limits, and differential-routing connections against the manufacturer datasheet. Also check whether an alternative uses different switched-pin or common-pin assignments, because those differences can prevent operation even when the land pattern and channel count appear identical.

Allow adequate acquisition time after changing address and ENABLE states. The settling interval must include address-decoder propagation, switch-transition behavior, charge injection, and the acquisition time required by the downstream converter or sample-and-hold circuit. A fixed delay that works with one source impedance may be inadequate with a different cable or sensor. Establish timing from worst-case signal amplitude, source impedance, temperature, and system tolerance rather than from nominal timing alone.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

No definitive compliance declarations were identified in the product-page and distributor snippets. The DG406 family is not stated to be AEC-Q100 qualified; confirm the ordered part's qualification status with the manufacturer before automotive use.

Related Searches

DG406DYZ datasheet DG406DYZ pinout DG406DYZ datasheet pdf DG406DYZ equivalent DG406DYZ replacement DG406DYZ cross reference DG406DYZ vs DG406DN+T DG406DYZ 16 channel mux DG406DYZ SOIC-28 DG406DYZ application circuit Renesas DG406DYZ DG406DYZ price

Related Components & Terms

Renesas Electronics DG406DYZ DG406DY-T DG406DY DG406DW-E3 DG406EWI+T DG406EWI-T DG406DN+T Maxim Integrated Analog Devices CMOS analog multiplexer analog multiplexer analog switch interface IC semiconductor TTL-compatible logic CMOS-compatible logic single-ended routing differential routing SOIC-28 surface-mount package on-resistance ENABLE input data-acquisition system
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details