DS90LV027M/NOPB - 155Mbps Dual LVDS Driver | Texas Instruments
MPN: DS90LV027M/NOPB ✓ ActiveDS90LV027M/NOPB Overview
An LVDS driver is a high-speed interface device that converts low-voltage logic signals into balanced differential signals. This differential signaling method belongs to the broader interface IC hierarchy and reduces susceptibility to common-mode noise compared with single-ended transmission. The DS90LV027M/NOPB is intended for designs that require low power dissipation, controlled output current, and minimized short-circuit fault current.
The dual-driver architecture provides two independent channels in one package, reducing board area when two LVDS links are required. Its current-mode output keeps dissipation low even at high operating frequencies, while the short-circuit protection characteristic limits fault current. The flow-through pin arrangement also supports straightforward routing of differential pairs and simplifies PCB layout compared with packages that require inputs and outputs on opposing sides.
Operation across a -40°C to +85°C temperature range makes the device appropriate for industrial and commercial equipment. The 8-lead SOIC package is available in a small-board footprint and uses a standard pin arrangement. At 3.3 V supply voltage, the device combines a 0.45 V differential output with data-rate capability listed for the family in excess of 600 Mbps, allowing it to address both established 155 Mbps links and higher-speed LVDS signaling requirements.
Typical uses include industrial control links, test and measurement equipment, computer interfaces, video and display links, and communication equipment that transfers data between circuit boards. The dual-channel configuration is especially useful for clock-plus-data, serial-backplane, point-to-point, and parallel-to-serial interface arrangements where cable-length and common-mode-noise performance are important.
PCB implementation should preserve the flow-through routing of each differential pair and provide a continuous return path beneath the traces. Keep the two conductors of each pair at a consistent width and spacing, minimize stubs, and place any required termination close to the receiving device. Decoupling capacitors should be connected directly to the supply and ground pins with short, low-inductance paths.
This product page organizes the device specifications, verified package details, pricing context, drop-in ordering variants, and application guidance into one engineering reference. It also distinguishes the electrically equivalent order codes from the physical packing options so designers can select the correct manufacturer part number without changing the PCB footprint.
Drop-in alternatives for DS90LV027M/NOPB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with DS90LV027M/NOPB (same form factor and footprint) — differing in PCB Layout, Package, Device Type, Number of Drivers, Operating Temperature.
DS90LV027M
✅ Drop-InContact for price
View Datasheet →DS90LV027MX/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV027M
✅ Drop-InContact for price
View Datasheet →DS90LV027M/NOPB Specifications
| Product Type | Dual LVDS differential driver |
| Number of Drivers | 2 channels |
| Technology | CMOS |
| Listed Data Rate | 155 Mbps |
| Family Maximum Data Rate | In excess of 600 Mbps |
| Maximum Clock Frequency | 300 MHz |
| Supply Voltage | 3.3 V |
| Differential Output Voltage | 0.45 V |
| Output Architecture | Current mode |
| Short-Circuit Fault Current | Minimized by current-mode output architecture |
| Power Dissipation | Low at high frequency |
| Operating Temperature | -40°C to +85°C |
| Package | 8-lead SOIC |
| Number of Pins | 8 pins |
| PCB Layout | Flow-through design |
| Packing Option | Tube |
DS90LV027M/NOPB 8-lead soic Pin Configuration Guide
Pin configuration for DS90LV027M/NOPB (8-lead soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for DS90LV027M/NOPB.
Refer to the datasheet for full pin configuration.
Typical Applications
DS90LV027M/NOPB is suitable for 6 applications: Industrial Control Links, Test and Measurement Equipment, Computer Interface Connections, Video and Display Interfaces, Communication Backplanes, Clock and Data Transmission.
Industrial Control Links
The DS90LV027M/NOPB is suitable for balanced communication links between industrial controllers, sensor interfaces, and remote I/O modules. Its two current-mode LVDS outputs support two differential channels from one 8-lead SOIC package, helping conserve board area in compact control hardware. The 3.3 V supply integrates easily with modern digital logic, while the 0.45 V differential output provides a defined signaling level for cable connections. The flow-through arrangement also simplifies routing between source and destination devices. For a reliable industrial design, keep each differential pair tightly coupled, provide a continuous ground reference, and verify that the attached receiver, cable length, and termination method satisfy the interface timing and common-mode requirements.
Recommended
Test and Measurement Equipment
The DS90LV027M/NOPB can provide low-power differential drive for test and measurement instruments that transfer synchronization, command, or measurement data between circuit boards. The dual-channel configuration supports architectures such as clock-plus-data without requiring two separate driver packages. At a 3.3 V supply, the device is compatible with common CMOS control logic, and its current-mode outputs are designed to limit power dissipation at high frequency. The 8-lead SOIC package is useful where instrument density matters. Keep the driver close to the connector or receiving circuitry, minimize connector-to-driver trace length, and confirm that the selected receiver and termination preserve signal timing over the full operating-temperature range.
Recommended
Computer Interface Connections
The DS90LV027M/NOPB is appropriate for point-to-point computer and peripheral interfaces that benefit from balanced differential signaling. Its two LVDS channels can carry independent data streams, while the 155 Mbps listed rate is suitable for many legacy and control-oriented links. Differential current-mode transmission reduces susceptibility to common-mode noise compared with single-ended routing, making the device useful where ground offsets or nearby switching circuitry may affect signal integrity. The 8-lead SOIC package permits direct placement near a connector. For reliable results, match differential trace geometry to the board stack-up, provide a nearby receiver termination, avoid stubs, and verify the interface timing margin at the intended clock frequency.
Recommended
Video and Display Interfaces
The DS90LV027M/NOPB can drive low-voltage differential links used between display-processing electronics and external interface circuitry. The dual output supports two complementary channels in one compact 8-lead SOIC package, while the 3.3 V operation and low-power current-mode design are well suited to dense digital systems. Balanced signaling helps maintain signal integrity when data crosses between circuit-board regions or through a cable. The family capability listed in excess of 600 Mbps provides additional design headroom for faster links. The actual pixel or symbol rate must be checked against the receiver requirements. Keep the differential pair impedance controlled, maintain a continuous reference plane, and place any receiver termination according to the selected LVDS topology.
Recommended
Communication Backplanes
The DS90LV027M/NOPB is applicable to communication equipment that uses short, point-to-point differential links between line cards, modules, or processors. Its current-mode output architecture is designed to maintain low power dissipation at high frequency and to minimize fault current during a short circuit. Two independently driven channels can support data and clock routing or separate communication lanes. The flow-through SOIC layout helps preserve a direct source-to-destination path, although the package still requires careful impedance-controlled routing. Define the receiver input, cable or trace length, and termination before layout. Then keep both conductors of a pair at uniform spacing, avoid unnecessary layer changes, and ensure the power return path remains continuous beneath the link.
Recommended
Clock and Data Transmission
The DS90LV027M/NOPB can transmit a clock and data channel as a pair of differential outputs to a compatible receiver. This arrangement is useful in compact systems requiring deterministic timing across a short cable or PCB link, particularly when single-ended clock routing would be more susceptible to noise coupling. The 3.3 V device supports two balanced outputs from one 8-lead SOIC package and has a listed 155 Mbps rate for the exact orderable part. Maintain matched routing between the clock and data channel paths, preserve the receiver's required input thresholds, and account for skew introduced by trace geometry or cable. Validate the complete eye and timing margin across temperature rather than relying only on the nominal data-rate specification.
Recommended
Recommended Products Summary
Engineering reference data for DS90LV027M/NOPB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | DS90LV027M | DS90LV027MX/NOPB | DS90LV027 |
|---|---|---|---|---|
| Package | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Dual LVDS differential driver | Dual LVDS differential driver | Dual LVDS differential driver | Dual LVDS differential driver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Output Architecture | Current mode | Current mode | Current mode | Current mode |
| PCB Layout | Flow-through design | Flow-through design | Flow-through design | Flow-through design |
Key Differentiators
- Dual current-mode LVDS outputs in one compact package (vs DS90LV027M)
- Production-compatible ordering and packing choices (vs DS90LV027MX/NOPB)
- Flow-through package supports straightforward differential routing (vs DS90LV027)
Design Notes
Preserve the DS90LV027M/NOPB flow-through routing by placing each differential channel so the input, output, and return paths remain direct. Route the positive and negative conductors as a tightly coupled pair with uniform width and spacing, avoid split planes beneath the pair, and minimize vias because each discontinuity can degrade differential-mode edge quality. Continue the reference plane beneath the complete link so high-frequency return current has an uninterrupted path.
Connect the 3.3 V supply and ground pins with short, low-inductance traces and place the required bypass capacitor immediately adjacent to the device. Do not route the differential outputs through long supply branches or shared narrow traces, because current-mode output switching can couple disturbance into the supply network. Keep the capacitor connection loop as small as practical and provide an adequate ground-plane return without thermal or impedance discontinuities.
Verify the complete LVDS link with the intended receiver, cable or trace length, and termination arrangement. A 155 Mbps listed rate does not by itself guarantee timing margin across every channel or temperature condition. Account for input threshold, propagation delay, jitter, connector effects, and termination value. Keep both conductors of a pair geometrically matched, and avoid test pads or unused stubs that create impedance discontinuities.
Compliance Information
The /NOPB ordering suffix denotes the Texas Instruments no-Pb lead-free finish. RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status were not stated in the product listing.