Texas Instruments

DS90LV027M/NOPB - 155Mbps Dual LVDS Driver | Texas Instruments

MPN: DS90LV027M/NOPB ✓ Aktif
3.3 V Vdss Minimized by current-mode output architecture Id 8-lead SOIC Package 300 MHz Speed
MOQ: 1 |

DS90LV027M/NOPB Genel Bakış

Texas Instruments DS90LV027M/NOPB is a dual low-voltage differential signaling (LVDS) driver supporting 155 Mbps in an 8-lead SOIC package. The device provides two differential outputs, operates from a 3.3 V supply, and combines a CMOS implementation with current-mode output architecture. Its 0.45 V differential output voltage is suited to low-power, high-speed point-to-point interfaces.

An LVDS driver is a high-speed interface device that converts low-voltage logic signals into balanced differential signals. This differential signaling method belongs to the broader interface IC hierarchy and reduces susceptibility to common-mode noise compared with single-ended transmission. The DS90LV027M/NOPB is intended for designs that require low power dissipation, controlled output current, and minimized short-circuit fault current.

The dual-driver architecture provides two independent channels in one package, reducing board area when two LVDS links are required. Its current-mode output keeps dissipation low even at high operating frequencies, while the short-circuit protection characteristic limits fault current. The flow-through pin arrangement also supports straightforward routing of differential pairs and simplifies PCB layout compared with packages that require inputs and outputs on opposing sides.

Operation across a -40°C to +85°C temperature range makes the device appropriate for industrial and commercial equipment. The 8-lead SOIC package is available in a small-board footprint and uses a standard pin arrangement. At 3.3 V supply voltage, the device combines a 0.45 V differential output with data-rate capability listed for the family in excess of 600 Mbps, allowing it to address both established 155 Mbps links and higher-speed LVDS signaling requirements.

Typical uses include industrial control links, test and measurement equipment, computer interfaces, video and display links, and communication equipment that transfers data between circuit boards. The dual-channel configuration is especially useful for clock-plus-data, serial-backplane, point-to-point, and parallel-to-serial interface arrangements where cable-length and common-mode-noise performance are important.

PCB implementation should preserve the flow-through routing of each differential pair and provide a continuous return path beneath the traces. Keep the two conductors of each pair at a consistent width and spacing, minimize stubs, and place any required termination close to the receiving device. Decoupling capacitors should be connected directly to the supply and ground pins with short, low-inductance paths.

This product page organizes the device specifications, verified package details, pricing context, drop-in ordering variants, and application guidance into one engineering reference. It also distinguishes the electrically equivalent order codes from the physical packing options so designers can select the correct manufacturer part number without changing the PCB footprint.

Drop-in alternatifler için DS90LV027M/NOPB — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller DS90LV027M/NOPB (aynı form faktörü ve ayağa oturma) — farklı olan PCB Layout, Package, Device Type, Number of Drivers, Operating Temperature.

Texas Instruments
PCB Layout: Flow-through pin arrangement
Package: 8-lead SOIC, narrow body
Device Type: Dual LVDS differential line driver
Texas Instruments
PCB Layout: Flow-through pin arrangement
Device Type: Dual LVDS differential line and bus driver

DS90LV027M

✅ Yerleştirme
Texas Instruments
📦 8-lead SOIC
Dual LVDS differential line driver · CMOS · 2 drivers · 0 receivers · Greater than 600 Mbps · 300 MHz · 3.3 V · 3.0 V to 3.6 V

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

DS90LV027MX/NOPB

✅ Yerleştirme
📦 8-lead SOIC
Same 3.3 V, dual LVDS driver and 8-lead SOIC electrical function; packing format differs, with 0% change in the listed key ratings

📋 Katalogda Olmayan Referans Alternatifi

DS90LV027M

✅ Yerleştirme
Texas Instruments
📦 8-lead SOIC
Dual LVDS differential line driver · CMOS · 2 drivers · 0 receivers · Greater than 600 Mbps · 300 MHz · 3.3 V · 3.0 V to 3.6 V

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

DS90LV027M/NOPB Özellikler

Product Type Dual LVDS differential driver
Number of Drivers 2 channels
Technology CMOS
Listed Data Rate 155 Mbps
Family Maximum Data Rate In excess of 600 Mbps
Azami Saat Hızı 300 MHz
Besleme Gerilimi 3.3 V
Differential Output Voltage 0.45 V
Output Architecture Current mode
Short-Circuit Fault Current Minimized by current-mode output architecture
Power Dissipation Low at high frequency
İşletim Sıcaklığı -40°C to +85°C
Paket 8-lead SOIC
Pin Sayısı 8 pins
PCB Layout Flow-through design
Packing Option Tube

DS90LV027M/NOPB 8-lead soic Pin Yapısı Kılavuzu

DS90LV027M/NOPB (8-lead soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

8-lead soic paket pin çizelgesi için DS90LV027M/NOPB

Ayrıntılı pin çıkış verisi mevcut değil: DS90LV027M/NOPB.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

DS90LV027M/NOPB için uygundur 6 uygulamas: Industrial Control Links, Test and Measurement Equipment, Computer Interface Connections, Video and Display Interfaces, Communication Backplanes, Clock and Data Transmission.

🏭

Industrial Control Links

The DS90LV027M/NOPB is suitable for balanced communication links between industrial controllers, sensor interfaces, and remote I/O modules. Its two current-mode LVDS outputs support two differential channels from one 8-lead SOIC package, helping conserve board area in compact control hardware. The 3.3 V supply integrates easily with modern digital logic, while the 0.45 V differential output provides a defined signaling level for cable connections. The flow-through arrangement also simplifies routing between source and destination devices. For a reliable industrial design, keep each differential pair tightly coupled, provide a continuous ground reference, and verify that the attached receiver, cable length, and termination method satisfy the interface timing and common-mode requirements.

🔧

Test and Measurement Equipment

The DS90LV027M/NOPB can provide low-power differential drive for test and measurement instruments that transfer synchronization, command, or measurement data between circuit boards. The dual-channel configuration supports architectures such as clock-plus-data without requiring two separate driver packages. At a 3.3 V supply, the device is compatible with common CMOS control logic, and its current-mode outputs are designed to limit power dissipation at high frequency. The 8-lead SOIC package is useful where instrument density matters. Keep the driver close to the connector or receiving circuitry, minimize connector-to-driver trace length, and confirm that the selected receiver and termination preserve signal timing over the full operating-temperature range.

🖥️

Computer Interface Connections

The DS90LV027M/NOPB is appropriate for point-to-point computer and peripheral interfaces that benefit from balanced differential signaling. Its two LVDS channels can carry independent data streams, while the 155 Mbps listed rate is suitable for many legacy and control-oriented links. Differential current-mode transmission reduces susceptibility to common-mode noise compared with single-ended routing, making the device useful where ground offsets or nearby switching circuitry may affect signal integrity. The 8-lead SOIC package permits direct placement near a connector. For reliable results, match differential trace geometry to the board stack-up, provide a nearby receiver termination, avoid stubs, and verify the interface timing margin at the intended clock frequency.

📺

Video and Display Interfaces

The DS90LV027M/NOPB can drive low-voltage differential links used between display-processing electronics and external interface circuitry. The dual output supports two complementary channels in one compact 8-lead SOIC package, while the 3.3 V operation and low-power current-mode design are well suited to dense digital systems. Balanced signaling helps maintain signal integrity when data crosses between circuit-board regions or through a cable. The family capability listed in excess of 600 Mbps provides additional design headroom for faster links. The actual pixel or symbol rate must be checked against the receiver requirements. Keep the differential pair impedance controlled, maintain a continuous reference plane, and place any receiver termination according to the selected LVDS topology.

🌐

Communication Backplanes

The DS90LV027M/NOPB is applicable to communication equipment that uses short, point-to-point differential links between line cards, modules, or processors. Its current-mode output architecture is designed to maintain low power dissipation at high frequency and to minimize fault current during a short circuit. Two independently driven channels can support data and clock routing or separate communication lanes. The flow-through SOIC layout helps preserve a direct source-to-destination path, although the package still requires careful impedance-controlled routing. Define the receiver input, cable or trace length, and termination before layout. Then keep both conductors of a pair at uniform spacing, avoid unnecessary layer changes, and ensure the power return path remains continuous beneath the link.

⚡

Clock and Data Transmission

The DS90LV027M/NOPB can transmit a clock and data channel as a pair of differential outputs to a compatible receiver. This arrangement is useful in compact systems requiring deterministic timing across a short cable or PCB link, particularly when single-ended clock routing would be more susceptible to noise coupling. The 3.3 V device supports two balanced outputs from one 8-lead SOIC package and has a listed 155 Mbps rate for the exact orderable part. Maintain matched routing between the clock and data channel paths, preserve the receiver's required input thresholds, and account for skew introduced by trace geometry or cable. Validate the complete eye and timing margin across temperature rather than relying only on the nominal data-rate specification.

Önerilen Ürünler Özeti

DS90LV027M Texas Instruments Kullanıldığı Yer: Industrial Control Links, Computer Interface Connections, Video and Display Interfaces, Clock and Data Transmission DS90LV027MX/NOPB Tape-and-reel order form of the same driver Kullanıldığı Yer: Industrial Control Links, Computer Interface Connections, Communication Backplanes DS90LV027 Family-level ordering designation Kullanıldığı Yer: Test and Measurement Equipment, Video and Display Interfaces, Clock and Data Transmission DS90LV027M/NOPB Texas Instruments Kullanıldığı Yer: Test and Measurement Equipment, Communication Backplanes
What is the DS90LV027M/NOPB?
The DS90LV027M/NOPB is a Texas Instruments dual LVDS differential driver in an 8-lead SOIC package. According to the manufacturer datasheet, it contains two current-mode outputs, operates from a 3.3 V supply, produces a 0.45 V differential output, and uses a flow-through pin arrangement for PCB layout. It is intended for high-speed, low-power point-to-point signaling where balanced differential transmission is required.
What is the maximum data rate of DS90LV027M/NOPB?
The DS90LV027M/NOPB is listed at 155 Mbps for the exact orderable part, while the DS90LV027 family description supports data rates in excess of 600 Mbps, equivalent to 300 MHz clock operation. According to Texas Instruments documentation, the current-mode architecture is optimized for high-frequency operation with low power dissipation. Confirm the required data rate, timing margin, and load configuration in the manufacturer datasheet before releasing the design.
Where can I download the DS90LV027M/NOPB datasheet PDF?
The official DS90LV027M/NOPB datasheet PDF is available from the Texas Instruments literature link at https://www.ti.com/lit/gpn/DS90LV027. The manufacturer product page at https://www.ti.com/product/DS90LV027 also provides the family documentation and ordering information. Use the manufacturer datasheet for the final pin description, electrical characteristics, recommended operating conditions, and application circuit details.
Where can I find the DS90LV027M/NOPB pinout?
The DS90LV027M/NOPB uses an 8-lead SOIC package with a flow-through arrangement, and its authoritative pin description is shown in the manufacturer pin-description table. The exact signal names are not reproduced on this page because the product listing does not present the complete pin table. Use the pin-description table in the Texas Instruments datasheet when assigning tracks, connecting the supply, and documenting the board footprint.
What is the supply voltage of DS90LV027M/NOPB?
The DS90LV027M/NOPB operates from a 3.3 V supply. According to the Texas Instruments product documentation, the device is a 3.3 V CMOS LVDS driver with two current-mode differential outputs. Place the supply bypass capacitor close to the device and verify the absolute maximum and recommended operating conditions in the manufacturer datasheet before applying voltage.
Is DS90LV027M/NOPB suitable for industrial applications?
Yes, the DS90LV027M/NOPB is specified for a -40°C to +85°C operating-temperature range, which suits many commercial and industrial environments. Its 3.3 V supply, dual differential outputs, and low-power current-mode architecture are useful for factory automation, test equipment, and communication links. The device is not identified as AEC-Q100-qualified, so automotive qualification requires separate verification.
What is the difference between DS90LV027M/NOPB and DS90LV027MX/NOPB?
The DS90LV027M/NOPB and DS90LV027MX/NOPB describe the same DS90LV027 electrical function in the same 8-lead SOIC package, but the ordering suffixes identify different packing configurations. The M version is associated with tube packing, while the MX version is associated with tape-and-reel packing. Both remain pin-to-pin compatible and provide the same 3.3 V, dual-channel LVDS driver function.
When should I choose DS90LV027M/NOPB over another dual LVDS driver?
Choose the DS90LV027M/NOPB when the design requires a dual 3.3 V LVDS driver in an 8-lead SOIC footprint, especially when a flow-through layout and low-power current-mode operation are priorities. Consider another device only when it offers a verified advantage such as a different supply voltage, integrated enable control, stronger common-mode protection, or a lower specified channel count. Verify timing, output loading, and termination requirements before making a substitution.
What is the best drop-in replacement for DS90LV027M/NOPB?
DS90LV027M and DS90LV027MX/NOPB are the closest documented ordering alternatives because they retain the DS90LV027 function and 8-lead SOIC footprint. The former changes the ordering suffix, while the latter changes the packing format; both preserve the pin arrangement. No independently verified cross-manufacturer, pin-compatible alternative was identified, so a substitute should not be assumed without checking its pinout and electrical limits.
Can DS90LV027M/NOPB replace a generic dual LVDS driver?
The DS90LV027M/NOPB can replace a dual LVDS driver only if the candidate has the same 8-lead SOIC pin arrangement, supply voltage, differential output voltage, input thresholds, timing behavior, and termination expectations. Matching the package alone is insufficient because swapped input, output, enable, or ground pins can damage the circuit. Compare the candidate directly against the manufacturer pin table and electrical characteristics before installation.
Where can I buy DS90LV027M/NOPB online?
Use the Request a Quote form on this page to request current availability, unit pricing, and lead time for DS90LV027M/NOPB. The manufacturer part details page confirms the orderable tube-packaged device in an 8-pin SOIC package. Quote requests establish the current commercial terms directly without relying on a potentially stale catalog price.
What is the price of DS90LV027M/NOPB?
The current unit price for DS90LV027M/NOPB is returned through the Request a Quote form on this page. Pricing can vary with order quantity, packing format, delivery location, and market conditions, while the manufacturer identifies the M suffix with tube packing. Submit the desired quantity and project quantity to obtain current terms for the exact orderable part.
What is the lead time for DS90LV027M/NOPB?
The current lead time for DS90LV027M/NOPB should be confirmed through the Request a Quote form on this page. Lead time can depend on the requested quantity, factory inventory, tube packing, and shipment destination. Enter your forecast quantities so the commercial response reflects the quantity actually needed for production rather than a prototype-only quantity.
Is DS90LV027M/NOPB in stock?
Current DS90LV027M/NOPB inventory is determined when you submit a request through the Request a Quote form on this page. The manufacturer lists the M/NOPB configuration as an orderable tube-packed part, but live stock and scheduled delivery must be confirmed for the selected quantity. The quote response provides the most current availability and lead-time information.
What are the key specifications of DS90LV027M/NOPB that engineers should know?
The key specifications are a 3.3 V supply, two LVDS outputs, 0.45 V differential output voltage, a 155 Mbps listed data rate, and a -40°C to +85°C operating range. According to Texas Instruments documentation, the current-mode design reduces power dissipation at high frequency, minimizes short-circuit fault current, and provides an 8-lead SOIC flow-through layout. These parameters determine its suitability for high-speed, low-power differential links.
Is DS90LV027M/NOPB the same as DS90LV027M?
The DS90LV027M/NOPB and DS90LV027M identify the same base DS90LV027M device, with the /NOPB portion forming the complete Texas Instruments ordering suffix. Both use the 8-lead SOIC footprint and retain the same dual-channel LVDS driver function. The /NOPB ordering code also communicates the manufacturer's no-Pb lead-free finish designation, while the product listing identifies tube packing for the M version.
How should a DS90LV027M/NOPB LVDS link be laid out?
Route each DS90LV027M/NOPB differential pair as a controlled-impedance, tightly coupled pair and preserve the flow-through signal path. Keep the pair width and spacing consistent, minimize vias and stubs, and provide a continuous reference plane beneath the traces. Place decoupling directly at the supply and ground pins, and position the receiver termination according to the interface topology and the manufacturer application guidance.

Mühendislik referans verileri: DS90LV027M/NOPB — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose DS90LV027M/NOPB for a new design that requires two 3.3 V LVDS outputs in an 8-lead SOIC footprint, particularly when low-power current-mode operation and flow-through routing are useful. Choose DS90LV027MX/NOPB when automated surface-mount assembly requires tape-and-reel packing; its electrical function and pin arrangement are unchanged. Choose DS90LV027M when the manufacturer base ordering code is preferred for tube-packed procurement. The generic DS90LV027 family designation is useful when comparing the complete family but should be resolved to a specific orderable suffix before purchasing. No independently verified cross-manufacturer equivalent was identified, so do not substitute a generic LVDS driver based on package appearance alone. Confirm pin compatibility, supply voltage, output amplitude, timing, termination, and temperature limits against the manufacturer datasheet before approving any alternative.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün DS90LV027M DS90LV027MX/NOPB DS90LV027
Package 8-lead SOIC 8-lead SOIC 8-lead SOIC 8-lead SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Device Type Dual LVDS differential driver Dual LVDS differential driver Dual LVDS differential driver Dual LVDS differential driver
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V
Output Architecture Current mode Current mode Current mode Current mode
PCB Layout Flow-through design Flow-through design Flow-through design Flow-through design

Ana Farklılayıcılar

  • Dual current-mode LVDS outputs in one compact package (karşılaştırma:DS90LV027M)
  • Production-compatible ordering and packing choices (karşılaştırma:DS90LV027MX/NOPB)
  • Flow-through package supports straightforward differential routing (karşılaştırma:DS90LV027)

Tasarım Notları

Preserve the DS90LV027M/NOPB flow-through routing by placing each differential channel so the input, output, and return paths remain direct. Route the positive and negative conductors as a tightly coupled pair with uniform width and spacing, avoid split planes beneath the pair, and minimize vias because each discontinuity can degrade differential-mode edge quality. Continue the reference plane beneath the complete link so high-frequency return current has an uninterrupted path.

Connect the 3.3 V supply and ground pins with short, low-inductance traces and place the required bypass capacitor immediately adjacent to the device. Do not route the differential outputs through long supply branches or shared narrow traces, because current-mode output switching can couple disturbance into the supply network. Keep the capacitor connection loop as small as practical and provide an adequate ground-plane return without thermal or impedance discontinuities.

Verify the complete LVDS link with the intended receiver, cable or trace length, and termination arrangement. A 155 Mbps listed rate does not by itself guarantee timing margin across every channel or temperature condition. Account for input threshold, propagation delay, jitter, connector effects, and termination value. Keep both conductors of a pair geometrically matched, and avoid test pads or unused stubs that create impedance discontinuities.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Yes
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The /NOPB ordering suffix denotes the Texas Instruments no-Pb lead-free finish. RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status were not stated in the product listing.

İlgili Aramalar

DS90LV027M/NOPB datasheet DS90LV027M/NOPB pinout DS90LV027M/NOPB price DS90LV027M/NOPB replacement DS90LV027M/NOPB equivalent DS90LV027M/NOPB stock DS90LV027M datasheet DS90LV027MX/NOPB datasheet DS90LV027 dual LVDS driver DS90LV027 155Mbps SOIC-8 DS90LV027M vs DS90LV027MX/NOPB DS90LV027 industrial communication link

İlgili Bileşenler ve Terimler

Texas Instruments DS90LV027M/NOPB DS90LV027M DS90LV027MX/NOPB DS90LV027 LVDS low-voltage differential signaling differential driver line driver interface IC CMOS current-mode output 3.3 V 155 Mbps 0.45 V differential output 8-lead SOIC SOIC package surface mount SMD flow-through pin arrangement common-mode noise industrial control test and measurement computer interface video interface
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle