EFM32G280F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
MPN: EFM32G280F32-QFP100 ✓ ActiveEFM32G280F32-QFP100 Overview
A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and I/O into one compact component. The EFM32G280 belongs to the EFM32 Gecko family, a hierarchy of ARM Cortex-M3 microcontrollers designed for embedded control, low-power sensing, communications, and industrial applications. Its architecture provides general-purpose computation alongside dedicated timers and energy-management functions.
The EFM32G280F32-QFP100 includes 3 x 16-bit timers, 86 digital I/O pins, and operation up to 32 MHz. Its 32 kB flash stores firmware, while 8 kB RAM supports working data, stack space, and peripheral buffers. The 100-pin LQFP provides enough connections for external sensing interfaces, communications, control outputs, and debug or programming access without relying on a very small package.
The Cortex-M3 processor supports a 32-bit instruction set and an efficient embedded-control architecture. Silicon Labs positions the Gecko platform around low-energy operation, rapid transitions from energy-saving states, and multiple sleep-related operating modes. These characteristics help reduce the average energy consumed by systems that spend much of their time monitoring inputs rather than executing continuous computation.
Typical applications include low-power sensor nodes, connected industrial equipment, environmental monitoring, compact control systems, and energy-harvesting products. The combination of 86 digital I/O pins and three 16-bit timers is particularly useful when a design needs multiple discrete inputs, timing channels, motor or actuator control, and communication peripherals on a single controller.
PCB implementation should preserve the 100-pin LQFP footprint, provide clean grounding, and route sensitive signal paths away from switching nodes. Designers should also budget flash and RAM for the complete firmware, interrupt handlers, and application state rather than relying only on nominal application-code size. Confirm the complete pin assignments and peripheral multiplexing in the manufacturer pinout table before final routing.
This page consolidates the manufacturer specifications, package information, sourcing guidance, and design considerations needed to evaluate the EFM32G280F32-QFP100. It also identifies the constraints involved in finding a genuine same-footprint replacement, rather than presenting devices with incompatible memory sizes or peripheral configurations as drop-in choices.
Drop-in alternatives for EFM32G280F32-QFP100 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
EFM32G280F32G-E-QFP100
✅ Drop-In📋 Reference alternative (not in catalog)
EFM32G280F32-QFP100 Maximum Ratings & Electrical Characteristics
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 kB (32K x 8) |
| RAM | 8 kB |
| Digital I/O Pins | 86 pins |
| Timers | 3 x 16-bit timers |
| Processor Core | ARM Cortex-M3 |
| Architecture | 32-bit RISC |
| Package | 100-pin LQFP (14 x 14 mm) |
| Mounting Type | Surface mount |
| Supply Voltage | 2.5 V to 3.3 V |
| Core Count | 1 core |
| Programmable I/O | 86 digital I/O pins |
| Energy-Saving Modes | Multiple low-energy operating modes |
EFM32G280F32-QFP100 100-pin lqfp (14 x 14 mm) Pin Configuration Guide
Pin configuration for EFM32G280F32-QFP100 (100-pin lqfp (14 x 14 mm) package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for EFM32G280F32-QFP100.
Refer to the datasheet for full pin configuration.
Typical Applications
EFM32G280F32-QFP100 is suitable for 6 applications: Low-Power Environmental Sensor Node, Industrial Condition Monitoring, Connected Building Control, Motor and Actuator Control, Battery-Powered Data Acquisition, Energy-Saving Portable Instrument.
Low-Power Environmental Sensor Node
The EFM32G280F32-QFP100 fits environmental monitoring nodes that sample sensors, filter readings, and remain inactive for long periods. Its 32 MHz ARM Cortex-M3 core can process local measurements without a higher-power processor, while the 86 digital I/O pins can accommodate sensing inputs, alarms, status indicators, and communications links. The device’s energy-saving modes and fast wake-up behavior are especially useful in battery-operated installations that alternate between measurement and sleep. For a 3.3 V system, its stated 2.5 V to 3.3 V operating range is compatible with common sensor and radio supply arrangements. Designers should allocate the 8 kB RAM for acquisition buffers, protocol state, and the stack, and reserve part of the 32 kB flash for firmware updates or dual-image storage.
Recommended
Industrial Condition Monitoring
The EFM32G280F32-QFP100 is suitable for industrial condition-monitoring equipment that combines several digital inputs with periodic measurement and alarm functions. Its 86 digital I/O pins reduce the need for external I/O expanders when connecting switch states, discrete sensors, relay drivers, and status signals. Three 16-bit timers support periodic sampling, timeout management, and timing functions, while the 32 MHz Cortex-M3 core provides enough performance for local signal conditioning and communication framing. The 100-pin LQFP also leaves room for debug, programming, and interface signals without an extremely compact package. A robust implementation should isolate external field wiring, protect I/O pins from surge events, and validate the device’s operating-temperature grade against the installation environment.
Recommended
Connected Building Control
The EFM32G280F32-QFP100 can serve as the local controller in a connected building system combining occupancy sensors, lighting controls, HVAC interfaces, and remote status reporting. Its 86 digital I/O pins provide substantial control capacity, and the three 16-bit timers are useful for periodic polling, actuator sequencing, and communication timeouts. The 32 MHz Cortex-M3 core can handle protocol tasks and application logic while the low-energy modes reduce consumption during idle periods. Because multiple loads may be inductive or switch noisy, the design should keep motor, relay, and switching-regulator paths away from sensitive sensor inputs. Firmware should also include communication retries and actuator state checks, since the 8 kB RAM must be carefully budgeted when several communication buffers are active.
Recommended
Motor and Actuator Control
The EFM32G280F32-QFP100 is appropriate for compact actuator-control boards requiring a responsive processor, multiple digital signals, and dedicated timing resources. Its three 16-bit timers can be allocated among control-loop timing, input capture, output compare, and periodic maintenance tasks, while 86 digital I/O pins allow connection of position sensors, limit switches, drivers, and status signals. The 32 MHz Cortex-M3 core supports deterministic supervisory logic without requiring a larger microcontroller. A practical design should use external driver circuitry for motors and high-current loads, include pull resistors and protection networks on exposed signals, and route return currents away from the MCU. Firmware timing should be verified against the actuator’s mechanical and electrical requirements because nominal CPU frequency alone does not guarantee a particular control-loop rate.
Recommended
Battery-Powered Data Acquisition
The EFM32G280F32-QFP100 supports compact battery-powered data-acquisition systems that gather several sensor channels and store or transmit processed results. The 32 kB flash provides space for application firmware and moderate local buffering, while 8 kB RAM can hold active samples and communication structures. Its 86 digital I/O pins make it practical to connect multiplexed inputs, trigger signals, and peripheral status lines without adding a large I/O expander. The processor’s 32 MHz rating provides useful throughput for calibration, filtering, and packet preparation. Low-energy operation should be designed at the system level: switch off unused peripherals, avoid continuous polling, and place the controller into an appropriate sleep mode between acquisition events. ADC-specific accuracy and peripheral timing must be evaluated from the family documentation.
Recommended
Energy-Saving Portable Instrument
The EFM32G280F32-QFP100 suits portable measurement instruments where display updates, sensor acquisition, and user inputs must be handled without continuous full-power operation. Its 32 MHz Cortex-M3 core can execute the measurement sequence and interface logic, while the low-energy platform supports fast transitions between active work and energy-saving states. The three 16-bit timers provide capture and periodic timing functions, and 86 digital I/O pins leave capacity for buttons, indicators, sensors, and serial links. In a compact handheld design, the 100-pin LQFP is larger than a leadless package but simplifies prototype assembly and provides generous routing access around the device. Power-budget calculations should include regulator losses, pull networks, and indicator consumption so that estimated battery life reflects the complete load rather than only the MCU sleep current.
Recommended
Recommended Products Summary
Engineering reference data for EFM32G280F32-QFP100 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | EFM32G280F32G-E-QFP100 |
|---|---|---|
| Brand | Silicon Labs | Silicon Labs |
| Package | 100-LQFP (14 x 14 mm) | 100-LQFP (14 x 14 mm) |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz |
| Flash Memory | 32 kB | 32 kB |
| RAM | 8 kB | 8 kB |
| Digital I/O Pins | 86 pins | 86 pins |
| Timers | 3 x 16-bit timers | 3 x 16-bit timers |
| Supply Voltage | 2.5 V to 3.3 V | 2.5 V to 3.3 V |
Key Differentiators
- Retains the compact memory profile while offering broad I/O capacity (vs EFM32G280F128-QFP100)
- Matches the key processing and memory ratings of the closest ordering alternative (vs EFM32G280F32G-E-QFP100)
- Provides extensive pin availability for embedded control without an external expander (vs EFM32G280F128-QFP100)
Design Notes
Route the EFM32G280F32-QFP100 on a PCB footprint matching its 100-pin LQFP outline. Start assignment with the manufacturer pin-description table, then resolve alternate-function conflicts for timers, communications, debug, and general-purpose I/O. Keep the crystal or clock circuitry close to the relevant pins, provide continuous ground-plane return paths, and avoid placing high-current switching loops beneath sensitive input or clock nets. Verify courtyard, paste, and solder-mask patterns against the current package drawing before fabrication.
Design the supply network for the stated 2.5 V to 3.3 V operating range and place the required bulk and local decoupling capacitors close to their associated supply pins. Separate noisy switching-regulator paths from analog or sensor inputs, and verify startup, brownout, and shutdown behavior against the complete power tree. Do not estimate the power budget from CPU frequency alone; include peripherals, external pull networks, LEDs, communications, and leakage paths when calculating average and peak current.
Avoid treating a same-package MCU as a drop-in replacement unless its memory, pin multiplexing, peripheral set, clock behavior, and software requirements match. EFM32G280 devices with larger flash capacities are not equivalent substitutes for the 32 kB F32 configuration, and a cross-brand Cortex-M3 part can require different peripheral initialization, pin assignments, and driver support. Confirm startup files, SDK compatibility, boot behavior, and programming connections before committing an alternative to a production schematic.
Preserve a quiet return path for every signal crossing between analog sensing, digital control, and external communications. Keep clock traces short and avoid routing them parallel to switching-node copper. Where a connector exposes external signals, place protection components near the connector rather than near the MCU so surge current is stopped before entering the board. Use the EFM32G280F32-QFP100’s 86 digital I/O pins intentionally; excess connections can create unnecessary leakage and complicate firmware ownership.
Compliance Information
Material-compliance declarations must be confirmed for the exact orderable MPN through current Silicon Labs documentation.