ICS527R-03 - 160MHz Zero-Delay Clock Buffer | Renesas
MPN: ICS527R-03 ✗ End of LifeICS527R-03 Overview
A zero-delay buffer is a clock-buffer IC that offers a very small propagation delay while providing buffering between a clock source and one or more receiving circuits. Clock buffers help isolate the source from downstream loading, reproduce the clock waveform with controlled edge relationships, and simplify distribution across multiple digital blocks. In the broader hierarchy, ICS527R-03 belongs to the clock and timing IC family, which includes clock buffers, clock slicers, clock generators, phase-locked loops, and frequency synthesizers.
The main published specifications identify a maximum operating frequency of 160 MHz and use of a 28-SSOP package measuring 0.154 inch, or 3.90 mm, in width. The 3.15 V to 3.45 V operating-supply range supports low-voltage clocking systems. ICS527R-03 is also described as a fanout or distribution buffer with zero delay, a zero-skew clock-slicing function, and user-configurable PECL input behavior. These characteristics make the device relevant to processors, network interfaces, serializer or deserializer chains, test equipment, and other systems requiring a locally buffered clock.
Clock integrity depends on preserving edge amplitude, rise and fall times, duty cycle, and inter-output timing relationships. A zero-delay architecture is valuable when one source must feed several destinations without allowing receiver input capacitance or board loading to disturb the original clock source. The available listing identifies one output in its abbreviated product description, but it does not expose the complete pin table, input configuration fields, output-enable logic, or detailed timing limits. Those details should be taken directly from the Renesas 527-03 datasheet before schematic capture.
Typical uses include buffering a reference clock into a digital ASIC, distributing a communications clock between parallel processing sections, and regenerating a PECL-compatible clock within high-speed test and measurement systems. Because the ICS527R-03 operates from a narrow 3.3 V-class supply range, the input logic levels and downstream supply voltages must be compatible. Short, impedance-controlled clock traces and solid ground-plane return paths are important when preserving the 160 MHz operating capability.
Designers should reserve the pins shown as control or configuration inputs for their required levels rather than treating unused clock-buffer pins as arbitrary no-connect locations. Termination, biasing, and decoupling depend on the selected PECL input configuration and the particular clock topology. The 28-SSOP footprint requires careful assembly planning because the fine-pitch package has a 3.90 mm body width and may be difficult to rework manually.
This product page consolidates the exact package, frequency, voltage, lifecycle, and sourcing information visible for ICS527R-03 with application guidance, comparison considerations, and practical clock-layout notes. It also distinguishes the device from related 527-series variants and explains which electrical and pin-level details engineers must confirm in the manufacturer datasheet before releasing a production design.
Drop-in alternatives for ICS527R-03 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ICS527R-03 (same form factor and footprint) — differing in Package.
ICS527R-01IT
✅ Drop-In📋 Reference alternative (not in catalog)
ICS527R-01T
✅ Drop-In📋 Reference alternative (not in catalog)
ICS527R-04
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →ICS527R-03 Specifications
| Product Type | Zero-delay clock buffer and clock distributor |
| Maximum Clock Frequency | 160 MHz |
| Supply Voltage Range | 3.15 V to 3.45 V |
| Number of Outputs | 1 output |
| Input Configuration | User-configurable PECL input |
| Package | 28-SSOP (0.154 inch, 3.90 mm width) |
| Mounting Type | Surface mount |
| Shipping Package | Tube |
| Lifecycle Status | Obsolete |
ICS527R-03 tube Pin Configuration Guide
Pin configuration for ICS527R-03 (tube package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for ICS527R-03.
Refer to the datasheet for full pin configuration.
Typical Applications
ICS527R-03 is suitable for 6 applications: ASIC Reference-Clock Buffering, Telecommunications Clock Distribution, High-Speed Test and Measurement, Processor Clock-Tree Isolation, Serializer and Deserializer Interfaces, Industrial Control and Instrumentation.
ASIC Reference-Clock Buffering
ICS527R-03 fits between a low-voltage reference clock and a demanding digital ASIC when the source must be isolated from receiver capacitance or clock-tree loading. Its 160 MHz maximum operating frequency provides a defined operating limit for common processor and interface clock rates, while the zero-delay buffer architecture minimizes added latency. The 3.15 V to 3.45 V supply range fits 3.3 V-class logic systems. In implementation, the clock source should meet the configured PECL input requirements, the supply should be decoupled near the device, and the output should reach a receiver with controlled impedance and a continuous ground-plane return path.
Recommended
Telecommunications Clock Distribution
The ICS527R-03 can buffer a 3.3 V-class system clock before it is distributed across telecommunications or networking logic. A zero-delay clock buffer helps preserve source integrity when the clock must drive multiple functional blocks, while its identified 160 MHz ceiling supports high-speed control and data-conversion sections. The user-configurable PECL input arrangement is particularly relevant where the upstream clock source uses ECL-family levels. Board implementation should include controlled-length clock routes, a continuous reference plane, local supply bypassing, and logic-level checks for every receiving device.
Recommended
High-Speed Test and Measurement
ICS527R-03 is applicable in test and measurement equipment where a clean, low-latency clock must be distributed from a central oscillator or pattern source. Its zero-delay characteristic avoids adding a substantial buffering phase delay, and the 160 MHz maximum frequency covers many legacy timing, communications, and instrumentation platforms. The 3.15 V to 3.45 V operating range supports compact low-voltage instrument architectures. Use short clock paths, maintain consistent return current, and observe the configured PECL input thresholds so that source amplitude, biasing, and termination are compatible.
Recommended
Processor Clock-Tree Isolation
ICS527R-03 can serve as an isolation stage between a master oscillator and a processor clock-tree input. Buffering reduces the burden placed directly on the oscillator by downstream input capacitance and allows a short local clock route to the processor. This is useful in legacy systems operating below or at 160 MHz and using a 3.15 V to 3.45 V clock domain. The implementation must preserve edge quality and duty cycle, verify input-versus-output logic thresholds, and provide local decoupling to prevent supply disturbances from appearing as clock jitter.
Recommended
Serializer and Deserializer Interfaces
ICS527R-03 is suitable for clock buffering around legacy serializer, deserializer, and parallel-interface devices that operate below the published 160 MHz limit. The clock buffer provides a local, low-delay distribution point and can isolate an upstream oscillator from switching loads that would otherwise degrade edge quality. Its narrow 3.3 V-class supply range requires compatible interface devices and careful logic-level matching. Engineers should use the configured PECL input method, verify timing budget margins, and route the output away from noisy switching nodes and power-converter regions.
Recommended
Industrial Control and Instrumentation
Legacy industrial control and instrumentation systems can use ICS527R-03 to distribute a low-voltage clock among control logic, converters, and communication blocks. Its 160 MHz rating provides ample bandwidth for many processor and fieldbus-adjacent clock domains, while the zero-delay function keeps the buffering stage transparent to timing. The 3.15 V to 3.45 V operating range supports integrated low-voltage systems. For reliable industrial implementation, verify temperature-grade requirements, isolate the clock route from motors and switching supplies, and confirm that the obsolete lifecycle status has been addressed through a planned sourcing or redesign strategy.
Recommended
Recommended Products Summary
Engineering reference data for ICS527R-03 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ICS527R-01IT | ICS527R-01T | ICS527R-04 |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 28-SSOP (0.154 inch, 3.90 mm width) | 28-SSOP | 28-SSOP | 28-SSOP |
| Device Function | User-configurable PECL zero-delay clock buffer and clock slicer | Zero-delay clock buffer and clock slicer | Zero-delay clock buffer and clock slicer | User-configurable zero-delay clock slicer |
Key Differentiators
- PECL-oriented configuration within the 527 clock-slicer family (vs ICS527R-01IT)
- Published 160 MHz operating point (vs ICS527R-01T)
- Narrow low-voltage operating range (vs ICS527R-04)
- Obsolete-status visibility for legacy procurement planning (vs ICS527R-01IT)
Design Notes
Treat the clock path as a controlled-impedance transmission line rather than an ordinary logic trace. Place the ICS527R-03 near the clock source or the first clock-consuming branch, minimize stub branches, and provide a continuous ground plane beneath the route. This reduces sensitivity to receiver capacitance and helps preserve clean edges at the published 160 MHz operating limit.
Do not assume that a PECL input can be connected directly to every 3.3 V clock source. Review the input-configuration truth table, required bias network, termination arrangement, and voltage thresholds in the Renesas 527-03 datasheet. Incorrect biasing or an incompatible source amplitude can cause unreliable switching even when the clock frequency is below 160 MHz.
Use the manufacturer SSOP land pattern and follow its solder-mask and paste recommendations. Keep the clock input and output routes away from switching power nodes, relay drivers, high-current edges, and isolation barriers. Short ground-return paths are especially important because the clock signal depends on a clean reference plane for predictable edge timing.
Place the required supply-decoupling capacitors close to the power and ground terminals and route them using short, low-inductance paths. Keep the clock buffer's supply network independent from noisy digital switching currents where practical. Operating the device only within the specified 3.15 V to 3.45 V range preserves margin for supply ripple and clock-edge quality.
The available information does not establish a worst-case internal power dissipation because propagation-delay and output-loading details are not published in the product listing. Estimate dissipation from the actual supply voltage, output toggle rate, load capacitance, and internal power specification before committing to a PCB thermal design. Validate the finished assembly at the highest expected clock activity and ambient temperature.
Compliance Information
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact ICS527R-03 ordering code.