ICS580M-01 270MHz 2:2 Clock Multiplexer | Renesas Electronics
MPN: ICS580M-01 ✗ End of LifeICS580M-01 Overview
A clock multiplexer is a timing-device category used to route one of two clock signals toward a downstream circuit while minimizing switching disturbances. This device combines clock selection with zero-delay buffer behavior, making it useful where a system must change clock sources without producing the short pulses or unwanted transitions that can disrupt digital logic, serializers, processors, and communication equipment.
The main operating characteristics are a maximum clock frequency of 270 MHz, a 2.5 V to 5.5 V supply-voltage range, and a 16-SOIC package. The 2:2 arrangement allows one selected clock to be distributed to two outputs, reducing the need for separate buffer devices when the same selected clock must reach more than one destination.
ICS580M-01 is intended for clock-distribution, clock-switching, and digital-system applications where clean transitions and controlled source selection are important. The zero-delay-buffer function is particularly relevant in systems where the multiplexer must present a predictable clock relationship to downstream circuitry. The exact input and output timing behavior should be confirmed from the manufacturer datasheet before using the device in a new design.
A typical implementation places the device between two candidate clock sources and the logic that requires a stable clock. The select control is driven by the system controller, while the two outputs are connected to the appropriate destination circuits. Designers should account for supply decoupling, controlled select transitions, trace impedance, and the relationship between the selected clock and surrounding circuitry.
For new layouts, place the device close to the clock source and the load being switched, route clock traces as controlled-impedance transmission lines where required, and keep the select control away from sensitive clock nodes. Verify the device’s operating limits, pin functions, and timing requirements in the manufacturer datasheet before production release.
This product page combines the manufacturer-aligned specifications, package information, sourcing structure, application guidance, and drop-in comparison information for ICS580M-01. It is intended to help engineers assess clock-multiplexer functionality and PCB reuse before completing a production design.
Drop-in alternatives for ICS580M-01 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
ICS580M-01I
✅ Drop-In📋 Reference alternative (not in catalog)
ICS580M-01LF
✅ Drop-In📋 Reference alternative (not in catalog)
ICS580M-01ILF
✅ Drop-In📋 Reference alternative (not in catalog)
580M-01LF
✅ Drop-In📋 Reference alternative (not in catalog)
580M-01L
✅ Drop-In📋 Reference alternative (not in catalog)
ICS580M-01 Specifications
| Product Type | Clock Multiplexer, Zero Delay Buffer IC |
| Multiplexer Configuration | 2:2 |
| Maximum Frequency | 270 MHz |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Input Signal | Clock |
| Output Signal | Clock |
| Number of Outputs | 2 |
| Package | 16-SOIC, 0.154 inch / 3.90 mm width |
| Switching Behavior | Glitch-free switching between two clock sources |
| Mounting Type | Surface Mount |
| Number of Pins | 16 pins |
ICS580M-01 16-soic, 0.154 inch / 3.90 mm width Pin Configuration Guide
Pin configuration for ICS580M-01 (16-soic, 0.154 inch / 3.90 mm width package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for ICS580M-01.
Refer to the datasheet for full pin configuration.
Typical Applications
ICS580M-01 is suitable for 6 applications: Dual-source clock selection, Processor clock-source failover, Telecommunications clock distribution, Network interface clock routing, Industrial data-acquisition timing, FPGA logic clocking.
Dual-source clock selection
The ICS580M-01 fits dual-source clock-selection systems that must route one of two incoming clocks to two downstream destinations without generating narrow unwanted pulses during a source change. Its 2:2 configuration reduces the number of separate selection and fan-out functions in a timing chain. The device operates from 2.5 V to 5.5 V and supports clocks up to 270 MHz, making it relevant to high-speed digital logic requiring controlled source transitions. Layout should keep clock paths short, preserve intended impedance, and place supply bypassing close to the device. The select-control signal must meet the timing requirements in the manufacturer datasheet, while receiver loading and trace length should be reviewed to ensure that the selected clock reaches downstream circuits with acceptable edge quality.
Recommended
Processor clock-source failover
ICS580M-01 can support a processor clock-source failover arrangement where two candidate clock sources are present but only one should drive the active timing path at a time. Its zero-delay-buffer function and two-output architecture allow the selected clock to reach two destinations while avoiding the glitches or short pulses associated with ordinary gate-based switching. Operation to 270 MHz supports demanding processor-interface timing, subject to the complete system budget. Engineers should verify processor clock-input tolerance, input-to-output timing, supply sequencing, and the maximum transition rate of the control signal. Short, properly referenced clock traces and local decoupling help preserve signal integrity during repeated source changes.
Recommended
Telecommunications clock distribution
The ICS580M-01 is appropriate for telecommunications equipment that selects between two clock domains and distributes the chosen signal to two functional blocks. Its 2:2 topology, 270 MHz maximum frequency, and 2.5 V to 5.5 V supply range fit timing systems requiring compact source selection close to active logic. The switching function is specified to avoid glitches and short pulses, helping protect downstream state machines and high-speed interfaces. In a production layout, use controlled-impedance routing for high-frequency clock nets, minimize stubs, and keep the select trace away from sensitive clock paths. Confirm the exact timing and output-load limits from the manufacturer datasheet before release.
Recommended
Network interface clock routing
ICS580M-01 can route one of two clocks toward network-interface circuitry while driving two output loads from the selected source. The device’s 270 MHz capability is useful in high-speed communication systems where fabric, serializer, or interface timing must remain stable during source changes. A dedicated multiplexer is preferable to ordinary logic gating when narrow pulses could be interpreted as valid clock edges and cause data errors. Place the ICS580M-01 near the clock-consuming circuitry, use short return paths and solid ground references, and avoid routing the select control adjacent to clock inputs. Validate input slew rate, output loading, and source-switch timing against the complete interface specification.
Recommended
Industrial data-acquisition timing
ICS580M-01 suits industrial data-acquisition systems that need to choose between two clocks for sampling, conversion, or control logic. The 2:2 output arrangement can distribute the selected clock to two acquisition-related blocks, while the specified glitch-free switching helps maintain deterministic control of sampling boundaries. Its 2.5 V to 5.5 V supply range supports integration with conventional digital voltage rails used in industrial equipment. Engineers should consider clock-jitter budget, maximum frequency, output loading, and the timing relationship between the select command and acquisition triggers. The device should be positioned close to the timing-consuming circuits, with local supply bypassing and controlled clock routing to reduce susceptibility to board-level noise.
Recommended
FPGA logic clocking
ICS580M-01 can provide source selection for FPGA-based systems that use two clocks and require the selected clock to reach two internal or external destinations. The 270 MHz maximum frequency makes the part relevant to moderately high-speed FPGA interfaces, while the zero-delay-buffer function avoids adding ordinary logic-gate pulse distortion at the selection stage. In a practical design, analyze the complete clocking architecture, including PLL outputs, fabric timing constraints, external clock-input tolerance, and any clock-gating requirements. Keep the device and output traces close to the receiving FPGA or buffer, maintain a continuous ground reference, and use the select control only when its timing satisfies the system’s switching sequence.
Recommended
Recommended Products Summary
Engineering reference data for ICS580M-01 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ICS580M-01I | ICS580M-01LF | ICS580M-01ILF | 580M-01LF | 580M-01L |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Device Type | 2:2 Clock Multiplexer, Zero Delay Buffer IC | Clock Multiplexer | Clock Multiplexer | Clock Multiplexer | Clock Multiplexer | Clock Multiplexer |
| Number of Outputs | 2 | 2 | 2 | 2 | 2 | 2 |
| Switching Behavior | No glitches or short pulses | Consistent functional characteristics | Consistent functional characteristics | Consistent functional characteristics | Consistent functional characteristics | Consistent functional characteristics |
Key Differentiators
- Combines source selection and two-output fan-out (vs ICS580M-01LF)
- Supports high-speed clock operation (vs ICS580M-01I)
- Glitch-free source switching (vs 580M-01LF)
- Broad compatible supply range (vs 580M-01L)
Design Notes
Route all four clock nets as a matched group and minimize branch stubs, especially because the device supports clocks up to 270 MHz. Keep the unused input terminated according to the manufacturer’s recommended input circuit and avoid leaving a high-speed clock node unterminated. Place the ICS580M-01 close to the receiving circuitry so that clock and select paths are not exposed to unrelated digital switching activity.
Separate the select-control trace from the clock inputs and outputs to reduce coupling into timing-sensitive nodes. Use a continuous ground reference under the clock routes, avoid plane splits beneath high-frequency clock traces, and use the package ground pins as part of a low-impedance return path. The datasheet pin table and recommended layout should control the final net assignment and component placement.
Do not treat a zero-delay-buffer description as permission to omit system timing analysis. The selected clock’s slew rate, output loading, source-switch timing, and downstream receiver requirements must satisfy the complete clock-domain specification. Also verify the exact ordering suffix, operating-temperature grade, and supply limits before using a related 16-SOIC replacement in production.
Follow the manufacturer’s recommended supply-bypass arrangement and place the decoupling capacitor close to the supply and ground pins. Keep the switching current path short and provide an appropriate ground return so clock outputs are not disturbed by supply noise during source changes. Verify the bypass component voltage rating, effective capacitance at the operating frequency, and the ripple profile of the upstream regulator.
Compliance Information
The verified product information does not state the requested compliance or material-category results. Confirm these attributes using the current manufacturer product documentation before regulated production use.