Renesas Electronics

ISL8485CBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas

MPN: ISL8485CBZ ✓ Active
4.5 V to 5.5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

ISL8485CBZ Overview

Renesas Electronics ISL8485CBZ is a 5 V, half-duplex, 1-transceiver/1-receiver RS-485 and RS-422 interface IC capable of operation to 5 Mbps. It is packaged in an 8-pin SOIC and supports a 4.5 V to 5.5 V supply range, providing tolerance for industrial 5 V rails. The device presents one unit load to an RS-485 bus and combines a balanced line driver, differential receiver, and half-duplex control in a compact package.

An RS-485/RS-422 transceiver is an interface device that translates logic-level signals into balanced differential signals for reliable communication over longer cables and electrically noisy environments. It belongs to the interface IC hierarchy, connecting digital controllers and processors to field buses or point-to-point differential links. Balanced signaling improves common-mode noise immunity, while bus direction control allows a single transceiver pair to support two-way communication.

Key characteristics include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply, and compatibility with both RS-485 and RS-422 communication standards. The half-duplex configuration multiplexes driver and receiver functions onto shared bus pins. Driver short-circuit current limiting and on-chip thermal shutdown help the device withstand bus contention without damage, as described in the Renesas ISL8485, ISL8490, and ISL8491 datasheet.

The ISL8485CBZ uses a BiCMOS implementation and presents one unit load to the RS-485 bus. Its receiver and driver interface supports industrial communication equipment where compactness and data rate are important. Because the transceiver operates from a narrow 5 V supply range, the system must maintain 4.5 V to 5.5 V at the device for specified operation. Cabling, termination, grounding, and controlled edge rates remain important when maximizing channel integrity.

Typical uses include industrial RS-485 controllers, building-automation equipment, factory data links, instrumentation gateways, and serial interface expansion for embedded processors. The 5 Mbps capability is useful for short, properly terminated links that need higher throughput than conventional slow-speed field-bus transceivers. For longer cables or lower data rates, engineers should also evaluate propagation delay, transceiver mode timing, and the loss budget of the selected cable.

Place the transceiver close to the connector and bus interface to minimize unprotected trace length. Use a proper differential pair with consistent geometry, connect the receiver ground reference appropriately, and install termination only where dictated by the network topology. Decoupling capacitors should be positioned close to the supply and ground pins, while the driver-enable and receiver-enable timing must leave sufficient propagation delay for clean direction changes.

Drop-in alternatives for ISL8485CBZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

ISL8485CB-T

✅ Drop-In
Renesas Electronics
📦 8-pin SOIC
RS-485/RS-422 line transceiver · 5 V · 4.5 V to 5.5 V · 5 Mbps · 1 driver · 1 receiver · Half-duplex · 1 unit load

Contact for price

View Datasheet →

ISL8495CB

✅ Drop-In
📦 8-pin SOIC
Equivalent high-speed serial interface; 5 Mbps-class operation retained, with enable and functional details requiring schematic confirmation

📋 Reference alternative (not in catalog)

ISL868DCBZ

✅ Drop-In
📦 8-pin SOIC
Equivalent high-speed serial interface in an 8-pin SOIC; exact supply, loading, and control-pin differences require review

📋 Reference alternative (not in catalog)

ISL8485CBZ Specifications

Product Type Half-duplex RS-485/RS-422 transceiver
Number of Transceivers 1
Number of Receivers 1
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 5 Mbps
Communication Standards RS-485 and RS-422
Duplex Mode Half-duplex
RS-485 Bus Loading 1 unit load
Process Technology BiCMOS
Driver Short-Circuit Protection Yes
Thermal Shutdown Yes
Package 8-pin SOIC
Mounting Type Surface mount
Operating Temperature Range 0°C to 70°C
ESD Rating 15 kV HBM

ISL8485CBZ Pin Configuration

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 RO — Receiver output
Pin 2 /RE — Active-low receiver enable
Pin 3 DE — Driver enable
Pin 4 DI — Driver input
Pin 5 GND — Ground
Pin 6 A — Non-inverting driver output and receiver input
Pin 7 B — Inverting driver output and receiver input
Pin 8 VCC — Positive supply

Typical Applications

ISL8485CBZ is suitable for 6 applications: Industrial RS-485 Controller, Factory Automation Data Link, Building Automation Network, Instrumentation Gateway, Embedded Serial Interface Expansion, Point-to-Point RS-422 Link.

🏭

Industrial RS-485 Controller

The ISL8485CBZ suits an industrial controller that must communicate with remote sensors or actuators over a balanced RS-485 bus. Its half-duplex architecture allows the same differential pair to carry commands and responses, while the 5 Mbps maximum rate supports short links with higher update throughput. The 4.5 V to 5.5 V operating range accommodates a regulated 5 V rail, and the one-unit-load interface helps control bus loading. A practical design should include connector-side surge protection, a continuous differential pair, chassis-to-signal-ground handling, and termination selected from the network topology.

🏭

Factory Automation Data Link

The ISL8485CBZ can connect a factory automation controller to remote I/O modules where deterministic half-duplex communication and noise immunity are important. Its differential RS-485 interface is designed for balanced cabling, while operation to 5 Mbps allows short inter-panel links to carry frequent status updates. The transceiver's one-unit-load bus presentation is useful when planning node count. Because the device is listed for 0°C to 70°C, use a thermally suitable enclosure or select a wider-temperature product when the installation environment exceeds that range.

🧩

Building Automation Network

The ISL8485CBZ is appropriate for a building-automation gateway communicating with distributed lighting, HVAC, or access-control modules over RS-485. Half-duplex control keeps the interface compact, and balanced signaling helps maintain data integrity across building wiring that may share noisy power infrastructure. The 5 V supply range integrates with common embedded rails. Design the network with controlled bus topology, one termination at each appropriate end, shield handling based on installation practice, and protection at externally accessible connectors.

🔧

Instrumentation Gateway

The ISL8485CBZ can bridge a local controller to remote instrumentation through a balanced RS-485 or RS-422 link. The transceiver's 5 Mbps capability benefits short links carrying sampled measurements or configuration data, and its half-duplex format reduces the number of interface signals when two-way traffic is not simultaneous. The 1-unit-load bus requirement must be included when calculating the permissible node count. Keep the differential route away from switching nodes and place common-mode protection close to the external connector.

🔧

Embedded Serial Interface Expansion

The ISL8485CBZ adds a robust balanced serial port to an embedded controller that has limited communication interfaces or requires a galvanically robust physical layer. Its 8-pin SOIC footprint supports compact board layouts, and the single-transceiver, single-receiver configuration covers the basic transmit and receive functions needed for a half-duplex link. The controller's UART and direction-control signals must be timed around driver and receiver propagation delays. Use a continuous ground reference appropriate to the installation and verify that the selected MCU and transceiver logic levels match the 5 V interface.

🌐

Point-to-Point RS-422 Link

The ISL8485CBZ supports a compact RS-422 point-to-point link when both ends use compatible balanced signaling and termination. Although the device is commonly associated with half-duplex RS-485 networks, the Renesas family is specified for RS-485 and RS-422 standards. A point-to-point arrangement can use one transceiver at each end with controlled direction timing. Verify enable polarity, idle-bus behavior, receiver fail-safe requirements, and grounding against the complete link specification before deployment.

What are the key specifications of ISL8485CBZ that engineers should know?
The ISL8485CBZ is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and supplied in an 8-pin SOIC. It operates from 4.5 V to 5.5 V, contains one transceiver and one receiver, and presents one unit load to an RS-485 bus. According to the Renesas ISL8485, ISL8490, and ISL8491 datasheet, the device uses BiCMOS circuitry, short-circuit-limited driver outputs, and on-chip thermal shutdown.
What is the operating voltage of ISL8485CBZ?
The ISL8485CBZ operates from a 4.5 V to 5.5 V supply, providing a 10% tolerance around its nominal 5 V operating point. According to the Renesas ISL8485 family datasheet, this supply range is a distinguishing family feature. The rail must remain within those limits for specified operation, so designers should check supply tolerance, startup sequencing, and the voltage at the transceiver when the upstream regulator operates near its limits.
What is the maximum data rate of ISL8485CBZ?
The ISL8485CBZ supports data rates up to 5 Mbps. The Renesas ISL8485 family datasheet identifies 5 Mbps as the maximum rate for the ISL8485, ISL8490, and ISL8491 family. Reaching that rate requires a short, properly terminated balanced pair with controlled impedance. Cable loss, stub length, grounding, and transceiver direction-control timing can reduce the practical usable distance even when the local signaling rate is supported.
Where can I download the ISL8485CBZ datasheet PDF?
The official ISL8485CBZ datasheet is available through the Renesas document page for the ISL8485, ISL8490, and ISL8491 family. That document contains the device pin descriptions, electrical characteristics, timing diagrams, and application guidance for the family. The ISL8485CBZ ordering information also appears on Renesas's part-details page, which provides the authoritative lifecycle and ordering context for the 8-pin SOIC configuration.
Where can I find the ISL8485CBZ pinout?
The ISL8485CBZ pinout is shown in the pin-description section of the Renesas ISL8485, ISL8490, and ISL8491 family datasheet. The 8-pin SOIC arrangement places RO on pin 1, receiver enable on pin 2, driver enable on pin 3, driver input on pin 4, ground on pin 5, driver non-inverting output on pin 6, driver inverting output on pin 7, and supply on pin 8. Use that pin-description table when assigning PCB tracks and protection networks.
What can replace ISL8485CBZ?
The closest documented same-manufacturer replacement is ISL8485CB-T because a published comparison identifies consistent terminals, packages, and principal performance characteristics with ISL8485CBZ. ISL8495CB and ISL868DCBZ are also identified as equivalent high-speed serial-interface products, but their detailed pin-level differences should be checked before production use. For any substitute, verify supply range, driver topology, enable polarity, bus loading, timing, and package pin assignments against the original schematic.
Is ISL8485CBZ the same as ISL8495CB?
No, ISL8485CBZ and ISL8495CB are related Renesas serial-interface devices but should not be assumed to be identical without reviewing their individual datasheets. ISL8485CBZ is a 5 V half-duplex RS-485/RS-422 transceiver operating up to 5 Mbps, while ISL8495CB is listed as an equivalent product in cross-reference results. Confirm driver-disable behavior, receiver topology, supply limits, and pin assignments before treating ISL8495CB as a drop-in replacement.
When should I choose ISL8485CBZ over a full-duplex RS-485 transceiver?
Choose ISL8485CBZ when the bus requires half-duplex operation and the same differential pair must carry both transmit and receive traffic. Its multiplexed half-duplex arrangement reduces the interface footprint to eight pins and supports operation up to 5 Mbps. A full-duplex transceiver is preferable when transmit and receive paths must operate simultaneously, require independent routing, or cannot share a driver-enable control sequence. Both architectures must satisfy the required cable length and timing budget.
Is ISL8485CBZ suitable for industrial RS-485 equipment?
The ISL8485CBZ is suitable for 5 V RS-485 equipment requiring a compact half-duplex interface and data rates up to 5 Mbps. Its 4.5 V to 5.5 V supply range, one-unit-load bus interface, short-circuit-limited driver, and thermal shutdown support robust bus communication. The Mouser listing identifies the ISL8485CBZ-T temperature range as 0°C to 70°C, so it is primarily suited to commercial-temperature equipment rather than unrestricted industrial-temperature installations.
What is the difference between ISL8485CBZ and ISL8485CBZ-T?
The ISL8485CBZ and ISL8485CBZ-T identify closely related ordering configurations of the same Renesas 8-pin SOIC transceiver family, with the suffix distinguishing the packaging or ordering form. Both are listed as one-transceiver, one-receiver, half-duplex 5 V RS-422/RS-485 devices. Engineers should use the ordering table in the family datasheet to confirm reel orientation, quantity, and lead-finish requirements while treating the electrical pinout as the family pinout.
How should the ISL8485CBZ be protected on an RS-485 bus?
Protect the ISL8485CBZ bus pins with appropriately rated surge and ESD protection, and use the driver and receiver pins only as directed by the family datasheet. Bus protection must tolerate the installation environment without adding excessive capacitance that degrades the 5 Mbps edge rate. Place protection close to the connector, route the balanced pair together, provide a suitable ground reference, and apply termination according to the complete bus topology rather than at every node.
Can ISL8485CBZ be used for RS-422 networks?
Yes, the ISL8485CBZ supports both RS-485 and RS-422 standards according to the Renesas family datasheet. The distinction lies primarily in how the balanced network is wired and terminated: RS-485 generally supports a multidrop bus with one driver active at a time, while RS-422 is commonly used for point-to-point or dedicated driver/receiver links. Confirm direction, grounding, termination, and cable topology for the specific network.
Does ISL8485CBZ have thermal shutdown and bus-contention protection?
Yes, the Renesas ISL8485 family datasheet states that driver short-circuit current limits and on-chip thermal shutdown protect the devices during severe bus contention. These protections improve robustness when a driver drives into a bus fault, but they do not remove the need for correct network design. Avoid sustained overload, maintain compliant supply voltage, and use suitable external protection for user-accessible or long field-bus wiring.
Where can I buy ISL8485CBZ and check its price and lead time?
Use the Request a Quote form on this page to request ISL8485CBZ pricing, stock confirmation, lead time, and order quantity. The form provides a single channel for obtaining a current commercial response without relying on a static price. For design confirmation, specify the required package, reel quantity, operating-temperature requirements, and shipment destination so the commercial response matches the intended production build.
How does the ISL8485CBZ compare with ISL868DCBZ for a 5 Mbps bus?
The ISL8485CBZ is a 5 V, half-duplex RS-485/RS-422 transceiver with one unit of bus loading and operation up to 5 Mbps. ISL868DCBZ is identified as a related high-speed serial-interface equivalent, but its detailed electrical and pin configuration must be confirmed before substitution. Compare data rate, supply range, receiver output behavior, driver-enable and receiver-enable inputs, fail-safe biasing, ESD level, and exact SOIC pin mapping in the manufacturer documentation.

Engineering reference data for ISL8485CBZ — comparison, design guidance, and compliance information.

Selection Guide

Choose ISL8485CBZ for a 5 V, half-duplex RS-485 or RS-422 link that must operate as quickly as 5 Mbps within an 8-pin SOIC design. ISL8485CB-T is the most straightforward documented substitute because its terminals, package, and principal performance characteristics are described as consistent, but production approval should still include a complete pin and ordering-code review. Consider ISL8495CB or ISL868DCBZ only after checking their individual datasheets for supply range, enable polarity, receiver output, bus loading, and timing. If simultaneous transmission and reception are required, choose a full-duplex transceiver rather than forcing the shared-bus architecture. For installations outside 0°C to 70°C, select a device rated for the actual ambient and enclosure temperature.

Comparison with Alternatives

Parameter This Product ISL8485CB-T ISL8495CB ISL868DCBZ
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Product Type Half-duplex RS-485/RS-422 transceiver Half-duplex RS-485/RS-422 transceiver High-speed serial interface equivalent High-speed serial interface equivalent

Key Differentiators

  • Documented pin-level and package compatibility (vs ISL8485CB-T)
  • Explicit one-unit-load RS-485 bus interface (vs ISL8495CB)
  • Half-duplex integration in eight pins (vs ISL868DCBZ)

Design Notes

Route A and B as a continuous differential pair from the transceiver to the connector, with closely matched geometry and a continuous reference plane. Place connector-side protection close to the entry point rather than beside the IC, because an unprotected trace can couple surge energy directly into the transceiver. Keep the pair away from switching nodes and high-current return paths. The 5 Mbps edge rate makes trace discontinuities and unequal impedance more consequential than they would be on a slow-speed bus.

Do not enable the driver and receiver simultaneously on a network whose nodes can drive at the same time. Sequence the /RE and DE controls around the relevant propagation delays, and account for the controller's UART settling time before asserting driver enable. Termination should be installed only at the physical ends of the intended bus. Adding 120-ohm termination at every node can overload the driver and prevent reliable signaling, particularly on short networks that do not require it.

Decouple the 5 V supply at the transceiver with the capacitor configuration specified by the Renesas family datasheet and place the components close to the VCC and GND pins. Confirm that the upstream rail remains between 4.5 V and 5.5 V during startup, load changes, and fault conditions. Because driver current can increase during bus contention, avoid placing excessive decoupling impedance between the transceiver and its local capacitor when designing for reliable operation.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The ISL8485CBZ is an RS-485/RS-422 interface IC rather than an automotive-qualified device. Compliance status requires confirmation from current manufacturer documentation or the relevant declaration.

Related Searches

ISL8485CBZ datasheet ISL8485CBZ pinout ISL8485CBZ datasheet pdf ISL8485CBZ replacement ISL8485CBZ equivalent ISL8485CBZ vs ISL8495CB ISL8485CBZ SOIC-8 footprint ISL8485CBZ 5Mbps RS-485 ISL8485CBZ RS-422 application circuit Renesas ISL8485CBZ ISL8485CBZ price ISL8485CBZ stock

Related Components & Terms

Renesas Electronics ISL8485CBZ ISL8485CB-T ISL8495CB ISL868DCBZ RS-485 RS-422 half-duplex transceiver differential interface IC balanced signaling BiCMOS data rate bus loading unit load driver enable receiver enable thermal shutdown short-circuit current limiting 8-pin SOIC SOIC package family surface-mount package industrial automation building automation instrumentation gateway factory data link
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details