ISL8485CBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas
MPN: ISL8485CBZ ✓ 啟用中ISL8485CBZ 概覽
An RS-485/RS-422 transceiver is an interface device that translates logic-level signals into balanced differential signals for reliable communication over longer cables and electrically noisy environments. It belongs to the interface IC hierarchy, connecting digital controllers and processors to field buses or point-to-point differential links. Balanced signaling improves common-mode noise immunity, while bus direction control allows a single transceiver pair to support two-way communication.
Key characteristics include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply, and compatibility with both RS-485 and RS-422 communication standards. The half-duplex configuration multiplexes driver and receiver functions onto shared bus pins. Driver short-circuit current limiting and on-chip thermal shutdown help the device withstand bus contention without damage, as described in the Renesas ISL8485, ISL8490, and ISL8491 datasheet.
The ISL8485CBZ uses a BiCMOS implementation and presents one unit load to the RS-485 bus. Its receiver and driver interface supports industrial communication equipment where compactness and data rate are important. Because the transceiver operates from a narrow 5 V supply range, the system must maintain 4.5 V to 5.5 V at the device for specified operation. Cabling, termination, grounding, and controlled edge rates remain important when maximizing channel integrity.
Typical uses include industrial RS-485 controllers, building-automation equipment, factory data links, instrumentation gateways, and serial interface expansion for embedded processors. The 5 Mbps capability is useful for short, properly terminated links that need higher throughput than conventional slow-speed field-bus transceivers. For longer cables or lower data rates, engineers should also evaluate propagation delay, transceiver mode timing, and the loss budget of the selected cable.
Place the transceiver close to the connector and bus interface to minimize unprotected trace length. Use a proper differential pair with consistent geometry, connect the receiver ground reference appropriately, and install termination only where dictated by the network topology. Decoupling capacitors should be positioned close to the supply and ground pins, while the driver-enable and receiver-enable timing must leave sufficient propagation delay for clean direction changes.
直接替換替代品,適用於 ISL8485CBZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ISL8485CB-T
✅ 直接替換聯絡詢價
查看資料表 →ISL8495CB
✅ 直接替換📋 參考替代品(不在目錄中)
ISL868DCBZ
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8485CBZ 規格
| Product Type | Half-duplex RS-485/RS-422 transceiver |
| Number of Transceivers | 1 |
| Number of Receivers | 1 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 5 Mbps |
| Communication Standards | RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| RS-485 Bus Loading | 1 unit load |
| Process Technology | BiCMOS |
| Driver Short-Circuit Protection | Yes |
| 過熱關機 | Yes |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| 工作溫度範圍 | 0°C to 70°C |
| ESD Rating | 15 kV HBM |
ISL8485CBZ 腳位配置
| 腳位 1 | RO — Receiver output |
| 腳位 2 | /RE — Active-low receiver enable |
| 腳位 3 | DE — Driver enable |
| 腳位 4 | DI — Driver input |
| 腳位 5 | GND — Ground |
| 腳位 6 | A — Non-inverting driver output and receiver input |
| 腳位 7 | B — Inverting driver output and receiver input |
| 腳位 8 | VCC — Positive supply |
典型應用
ISL8485CBZ 適用於 6 應用s: Industrial RS-485 Controller, Factory Automation Data Link, Building Automation Network, Instrumentation Gateway, Embedded Serial Interface Expansion, Point-to-Point RS-422 Link.
Industrial RS-485 Controller
The ISL8485CBZ suits an industrial controller that must communicate with remote sensors or actuators over a balanced RS-485 bus. Its half-duplex architecture allows the same differential pair to carry commands and responses, while the 5 Mbps maximum rate supports short links with higher update throughput. The 4.5 V to 5.5 V operating range accommodates a regulated 5 V rail, and the one-unit-load interface helps control bus loading. A practical design should include connector-side surge protection, a continuous differential pair, chassis-to-signal-ground handling, and termination selected from the network topology.
推薦
Factory Automation Data Link
The ISL8485CBZ can connect a factory automation controller to remote I/O modules where deterministic half-duplex communication and noise immunity are important. Its differential RS-485 interface is designed for balanced cabling, while operation to 5 Mbps allows short inter-panel links to carry frequent status updates. The transceiver's one-unit-load bus presentation is useful when planning node count. Because the device is listed for 0°C to 70°C, use a thermally suitable enclosure or select a wider-temperature product when the installation environment exceeds that range.
推薦
Building Automation Network
The ISL8485CBZ is appropriate for a building-automation gateway communicating with distributed lighting, HVAC, or access-control modules over RS-485. Half-duplex control keeps the interface compact, and balanced signaling helps maintain data integrity across building wiring that may share noisy power infrastructure. The 5 V supply range integrates with common embedded rails. Design the network with controlled bus topology, one termination at each appropriate end, shield handling based on installation practice, and protection at externally accessible connectors.
推薦
Instrumentation Gateway
The ISL8485CBZ can bridge a local controller to remote instrumentation through a balanced RS-485 or RS-422 link. The transceiver's 5 Mbps capability benefits short links carrying sampled measurements or configuration data, and its half-duplex format reduces the number of interface signals when two-way traffic is not simultaneous. The 1-unit-load bus requirement must be included when calculating the permissible node count. Keep the differential route away from switching nodes and place common-mode protection close to the external connector.
推薦
Embedded Serial Interface Expansion
The ISL8485CBZ adds a robust balanced serial port to an embedded controller that has limited communication interfaces or requires a galvanically robust physical layer. Its 8-pin SOIC footprint supports compact board layouts, and the single-transceiver, single-receiver configuration covers the basic transmit and receive functions needed for a half-duplex link. The controller's UART and direction-control signals must be timed around driver and receiver propagation delays. Use a continuous ground reference appropriate to the installation and verify that the selected MCU and transceiver logic levels match the 5 V interface.
推薦
Point-to-Point RS-422 Link
The ISL8485CBZ supports a compact RS-422 point-to-point link when both ends use compatible balanced signaling and termination. Although the device is commonly associated with half-duplex RS-485 networks, the Renesas family is specified for RS-485 and RS-422 standards. A point-to-point arrangement can use one transceiver at each end with controlled direction timing. Verify enable polarity, idle-bus behavior, receiver fail-safe requirements, and grounding against the complete link specification before deployment.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8485CBZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8485CB-T | ISL8495CB | ISL868DCBZ |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Product Type | Half-duplex RS-485/RS-422 transceiver | Half-duplex RS-485/RS-422 transceiver | High-speed serial interface equivalent | High-speed serial interface equivalent |
主要差異化特點
- Documented pin-level and package compatibility (對比ISL8485CB-T)
- Explicit one-unit-load RS-485 bus interface (對比ISL8495CB)
- Half-duplex integration in eight pins (對比ISL868DCBZ)
設計說明
Route A and B as a continuous differential pair from the transceiver to the connector, with closely matched geometry and a continuous reference plane. Place connector-side protection close to the entry point rather than beside the IC, because an unprotected trace can couple surge energy directly into the transceiver. Keep the pair away from switching nodes and high-current return paths. The 5 Mbps edge rate makes trace discontinuities and unequal impedance more consequential than they would be on a slow-speed bus.
Do not enable the driver and receiver simultaneously on a network whose nodes can drive at the same time. Sequence the /RE and DE controls around the relevant propagation delays, and account for the controller's UART settling time before asserting driver enable. Termination should be installed only at the physical ends of the intended bus. Adding 120-ohm termination at every node can overload the driver and prevent reliable signaling, particularly on short networks that do not require it.
Decouple the 5 V supply at the transceiver with the capacitor configuration specified by the Renesas family datasheet and place the components close to the VCC and GND pins. Confirm that the upstream rail remains between 4.5 V and 5.5 V during startup, load changes, and fault conditions. Because driver current can increase during bus contention, avoid placing excessive decoupling impedance between the transceiver and its local capacitor when designing for reliable operation.
合規資訊
The ISL8485CBZ is an RS-485/RS-422 interface IC rather than an automotive-qualified device. Compliance status requires confirmation from current manufacturer documentation or the relevant declaration.