LM201ANG - 1 MHz Non-Compensated Op Amp | onsemi
MPN: LM201ANG ✗ End of LifeLM201ANG Overview
An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its two inputs. Its applications include analog signal conditioning, closed-loop gain stages, active filtering, integrators, and feedback control. Unlike an internally compensated amplifier, the LM201ANG leaves compensation to the user, providing greater flexibility where gain-bandwidth behavior must be optimized for a particular circuit.
The LM201ANG combines a 1 MHz gain-bandwidth product with a single-amplifier configuration in a through-hole 8-pin PDIP package. Its non-compensated architecture requires an external compensation network to establish stable operation. The operating-temperature grade shown for this ordering code is -25°C to 85°C, making it suitable for conventional industrial and instrumentation environments within that temperature range.
Because the amplifier is not internally compensated, its dynamic behavior depends strongly on the selected compensation capacitor, circuit topology, closed-loop gain, noise gain, and load. Designers should use the compensation guidance and typical application circuits in the manufacturer datasheet rather than treating the 1 MHz figure as a fixed, topology-independent operating bandwidth. The device can therefore support different stability and bandwidth compromises in precision analog circuits.
Typical uses include low-frequency instrumentation amplifiers, active filters, sensor-conditioning channels, laboratory measurement equipment, and industrial control modules. The LM201ANG is especially relevant when an adjustable compensation capacitor provides more benefit than the simplicity of a unity-gain-stable internal compensation network. Its PDIP package also simplifies prototyping, inspection, and manual rework in low- to moderate-volume assemblies.
When laying out a circuit, keep the compensation capacitor close to the compensation pin and use a short, low-inductance feedback path. Check stability across the intended gain, load, supply, and temperature ranges rather than relying only on a nominal simulation result. The principal engineering trade-off is that external compensation adds component selection and validation effort but permits optimization that an internally compensated amplifier cannot provide.
This product page combines the exact ordering-code details, sourcing guidance, application context, and design considerations for the LM201ANG. It also distinguishes pin-compatible replacement options from devices that require a package change, helping engineers avoid a replacement that cannot be soldered into the existing footprint.
Drop-in alternatives for LM201ANG — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM201ANG (same form factor and footprint) — differing in Compensation Type.
LM201AN
✅ Drop-InContact for price
View Datasheet →LM201ANG Maximum Ratings & Electrical Characteristics
| Amplifier Type | Single general-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz |
| Compensation Type | Non-compensated; external compensation required |
| Number of Channels | 1 circuit |
| Number of Terminals | 8 terminals |
| Package Type | 8-pin PDIP |
| Terminal Form | Through-hole |
| Operating Temperature Range | -25°C to +85°C |
| Input Bias Current | 30 nA |
| Supply Voltage Span | 10 V to 44 V |
| Typical Supply Voltage | 15 V |
| Maximum Supply Voltage | 20 V |
| Common-Mode Rejection Ratio | 96 dB |
| RoHS Status | RoHS-compliant |
| Lead-Free Status | Lead-free |
| Green Component Status | Green |
| Output Short-Circuit Protection | Present |
| Input Overload Protection | Present |
LM201ANG 8-pin pdip Pin Configuration Guide
Pin configuration for LM201ANG (8-pin pdip package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LM201ANG.
Refer to the datasheet for full pin configuration.
Typical Applications
LM201ANG is suitable for 6 applications: Precision Instrumentation Signal Conditioning, Active Filter Design, Industrial Sensor Conditioning, Laboratory Voltage Buffer, Low-Frequency Control and Feedback, Precision Analog Measurement Module.
Precision Instrumentation Signal Conditioning
The LM201ANG fits low-frequency precision signal-conditioning channels because it provides a 1 MHz gain-bandwidth product, 30 nA input bias current, and 96 dB common-mode rejection in a single-amplifier 8-pin PDIP package. The non-compensated architecture allows the compensation capacitor to be selected for the actual noise gain and closed-loop gain, rather than accepting a fixed internal compensation network. Use it when the board must tolerate source resistance, cable capacitance, and reference-node behavior that could destabilize a unity-gain stage. Verify stability over the intended frequency range because the 1 MHz figure is a device parameter, not a guaranteed closed-loop bandwidth for every topology.
Recommended
Active Filter Design
The LM201ANG is useful in active-filter prototypes where a designer needs direct control over compensation rather than a fixed internally compensated response. Its 1 MHz gain-bandwidth product provides ample open-loop gain for many low- and moderate-frequency filter stages, while the external compensation capacitor can be tailored to the required noise gain and phase margin. An 8-pin PDIP format also makes it convenient for laboratory breadboards and iterative filter tuning. Select compensation using the manufacturer’s guidance, include the intended source and load impedances in the stability analysis, and test component tolerances because the external capacitor can alter both dynamics and effective bandwidth.
Recommended
Industrial Sensor Conditioning
For industrial sensor interfaces operating in the -25°C to 85°C range, the LM201ANG can amplify low-level differential signals while its 30 nA input bias current limits the disturbance applied to a high-impedance sensor. The 96 dB common-mode rejection ratio helps reject common-mode noise that can otherwise consume the available signal range. Place the device close to the compensation capacitor and keep feedback routing short to preserve stability. The component should be paired with sensor-specific input protection and filtering because amplifier ratings alone do not address sensor excitation, transient protection, or industrial surge requirements.
Recommended
Laboratory Voltage Buffer
The LM201ANG can implement a configurable laboratory buffer when the circuit requires user-selectable compensation and operates within its 10 V to 44 V supply span. The device’s single-channel architecture makes it straightforward to allocate one amplifier per signal path, and the through-hole 8-pin PDIP package simplifies instrument wiring and prototype replacement. Because the stage is non-compensated, calculate the compensation capacitor for the chosen noise gain and verify capacitive-load behavior. A 15 V supply is identified as typical, while the maximum operating voltage is 20 V, so protection and supply tolerances must be handled by the surrounding instrument circuitry.
Recommended
Low-Frequency Control and Feedback
A control loop that must be tuned against a known noise gain can benefit from the LM201ANG’s externally adjustable compensation. Rather than accepting a fixed unity-gain stability characteristic, the design engineer can select the compensation capacitor around the required response and account for component tolerances. The 1 MHz gain-bandwidth product and 96 dB common-mode rejection are useful for low-frequency feedback stages, while the -25°C to 85°C grade covers conventional industrial environments. Build a stability margin into the loop, observe phase margin across temperature and supply variation, and avoid treating the gain-bandwidth value as the loop bandwidth without completing the feedback analysis.
Recommended
Precision Analog Measurement Module
The LM201ANG is appropriate for a precision analog measurement module that combines a single amplifier with external compensation and requires through-hole assembly flexibility. Its 30 nA input bias current and 96 dB common-mode rejection support low-level measurement stages, while the 1 MHz gain-bandwidth product is sufficient for many measurement bandwidths. The non-compensated configuration also permits optimization when the source impedance creates a noise gain above the intended signal gain. Validate offset, bias-current effects, input common-mode range, and stability with the actual transducer and cable. Add input clamping and filtering ahead of the amplifier when the measurement source can exceed its safe operating limits.
Recommended
Recommended Products Summary
Engineering reference data for LM201ANG — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM201AN |
|---|---|---|
| Brand | onsemi | STMicroelectronics |
| Package | 8-PDIP | 8-DIP |
| Amplifier Configuration | Single circuit | Single circuit |
| Product Type | General-purpose operational amplifier | General-purpose operational amplifier |
Key Differentiators
- Externally adjustable compensation (vs LM201AN)
- Established through-hole package (vs LM201ADR2G)
- Defined low-level input characteristics (vs LM201AN)
Design Notes
Place the external compensation capacitor directly beside the compensation connection and minimize its trace length. Keep the amplifier feedback components close to the device, use short feedback loops, and separate sensitive input routing from output and compensation nodes. Because the LM201ANG is non-compensated, parasitic board capacitance can alter the compensation network and reduce phase margin. Review the physical layout with the intended source impedance, load, and compensation value.
Do not assume the 1 MHz gain-bandwidth product is the usable closed-loop bandwidth in every circuit. Determine the noise gain, select compensation for that gain, and verify stability across the required load and temperature range. Also observe the stated 10 V to 44 V supply span, 20 V maximum operating voltage, and -25°C to 85°C temperature range. A stable nominal simulation is insufficient if component tolerances or supply variation push the amplifier toward oscillation.
Design the supply rails with the 15 V typical and 20 V maximum operating-voltage conditions in mind. Include adequate bypassing at the device and account for input common-mode limits, output swing, and load-current requirements. The LM201ANG can be used only within its documented supply and signal limits, so rail protection is important when the amplifier receives external laboratory, industrial, or sensor signals. Verify startup and shutdown behavior as well as steady-state regulation.
Compliance Information
The component listing identifies LM201ANG as RoHS-compliant, lead-free, and a green electronic component. No separate automotive qualification or REACH declaration is identified for this ordering code.