LM201ANG - 1 MHz Non-Compensated Op Amp | onsemi
MPN: LM201ANG ✗ 停產LM201ANG 概覽
An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its two inputs. Its applications include analog signal conditioning, closed-loop gain stages, active filtering, integrators, and feedback control. Unlike an internally compensated amplifier, the LM201ANG leaves compensation to the user, providing greater flexibility where gain-bandwidth behavior must be optimized for a particular circuit.
The LM201ANG combines a 1 MHz gain-bandwidth product with a single-amplifier configuration in a through-hole 8-pin PDIP package. Its non-compensated architecture requires an external compensation network to establish stable operation. The operating-temperature grade shown for this ordering code is -25°C to 85°C, making it suitable for conventional industrial and instrumentation environments within that temperature range.
Because the amplifier is not internally compensated, its dynamic behavior depends strongly on the selected compensation capacitor, circuit topology, closed-loop gain, noise gain, and load. Designers should use the compensation guidance and typical application circuits in the manufacturer datasheet rather than treating the 1 MHz figure as a fixed, topology-independent operating bandwidth. The device can therefore support different stability and bandwidth compromises in precision analog circuits.
Typical uses include low-frequency instrumentation amplifiers, active filters, sensor-conditioning channels, laboratory measurement equipment, and industrial control modules. The LM201ANG is especially relevant when an adjustable compensation capacitor provides more benefit than the simplicity of a unity-gain-stable internal compensation network. Its PDIP package also simplifies prototyping, inspection, and manual rework in low- to moderate-volume assemblies.
When laying out a circuit, keep the compensation capacitor close to the compensation pin and use a short, low-inductance feedback path. Check stability across the intended gain, load, supply, and temperature ranges rather than relying only on a nominal simulation result. The principal engineering trade-off is that external compensation adds component selection and validation effort but permits optimization that an internally compensated amplifier cannot provide.
This product page combines the exact ordering-code details, sourcing guidance, application context, and design considerations for the LM201ANG. It also distinguishes pin-compatible replacement options from devices that require a package change, helping engineers avoid a replacement that cannot be soldered into the existing footprint.
直接替換替代品,適用於 LM201ANG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM201ANG (相同外形與佔位) — 差異在於 Compensation Type.
LM201ANG 最大額定值與電氣特性
| Amplifier Type | Single general-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz |
| Compensation Type | Non-compensated; external compensation required |
| Number of Channels | 1 circuit |
| Number of Terminals | 8 terminals |
| Package Type | 8-pin PDIP |
| Terminal Form | Through-hole |
| 工作溫度範圍 | -25°C to +85°C |
| Input Bias Current | 30 nA |
| Supply Voltage Span | 10 V to 44 V |
| Typical Supply Voltage | 15 V |
| Maximum Supply Voltage | 20 V |
| Common-Mode Rejection Ratio | 96 dB |
| RoHS 狀態 | RoHS-compliant |
| Lead-Free Status | Lead-free |
| Green Component Status | Green |
| Output Short-Circuit Protection | Present |
| Input Overload Protection | Present |
LM201ANG 8-pin pdip 腳位配置指南
LM201ANG(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM201ANG.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM201ANG 適用於 6 應用s: Precision Instrumentation Signal Conditioning, Active Filter Design, Industrial Sensor Conditioning, Laboratory Voltage Buffer, Low-Frequency Control and Feedback, Precision Analog Measurement Module.
Precision Instrumentation Signal Conditioning
The LM201ANG fits low-frequency precision signal-conditioning channels because it provides a 1 MHz gain-bandwidth product, 30 nA input bias current, and 96 dB common-mode rejection in a single-amplifier 8-pin PDIP package. The non-compensated architecture allows the compensation capacitor to be selected for the actual noise gain and closed-loop gain, rather than accepting a fixed internal compensation network. Use it when the board must tolerate source resistance, cable capacitance, and reference-node behavior that could destabilize a unity-gain stage. Verify stability over the intended frequency range because the 1 MHz figure is a device parameter, not a guaranteed closed-loop bandwidth for every topology.
推薦
Active Filter Design
The LM201ANG is useful in active-filter prototypes where a designer needs direct control over compensation rather than a fixed internally compensated response. Its 1 MHz gain-bandwidth product provides ample open-loop gain for many low- and moderate-frequency filter stages, while the external compensation capacitor can be tailored to the required noise gain and phase margin. An 8-pin PDIP format also makes it convenient for laboratory breadboards and iterative filter tuning. Select compensation using the manufacturer’s guidance, include the intended source and load impedances in the stability analysis, and test component tolerances because the external capacitor can alter both dynamics and effective bandwidth.
推薦
Industrial Sensor Conditioning
For industrial sensor interfaces operating in the -25°C to 85°C range, the LM201ANG can amplify low-level differential signals while its 30 nA input bias current limits the disturbance applied to a high-impedance sensor. The 96 dB common-mode rejection ratio helps reject common-mode noise that can otherwise consume the available signal range. Place the device close to the compensation capacitor and keep feedback routing short to preserve stability. The component should be paired with sensor-specific input protection and filtering because amplifier ratings alone do not address sensor excitation, transient protection, or industrial surge requirements.
推薦
Laboratory Voltage Buffer
The LM201ANG can implement a configurable laboratory buffer when the circuit requires user-selectable compensation and operates within its 10 V to 44 V supply span. The device’s single-channel architecture makes it straightforward to allocate one amplifier per signal path, and the through-hole 8-pin PDIP package simplifies instrument wiring and prototype replacement. Because the stage is non-compensated, calculate the compensation capacitor for the chosen noise gain and verify capacitive-load behavior. A 15 V supply is identified as typical, while the maximum operating voltage is 20 V, so protection and supply tolerances must be handled by the surrounding instrument circuitry.
推薦
Low-Frequency Control and Feedback
A control loop that must be tuned against a known noise gain can benefit from the LM201ANG’s externally adjustable compensation. Rather than accepting a fixed unity-gain stability characteristic, the design engineer can select the compensation capacitor around the required response and account for component tolerances. The 1 MHz gain-bandwidth product and 96 dB common-mode rejection are useful for low-frequency feedback stages, while the -25°C to 85°C grade covers conventional industrial environments. Build a stability margin into the loop, observe phase margin across temperature and supply variation, and avoid treating the gain-bandwidth value as the loop bandwidth without completing the feedback analysis.
推薦
Precision Analog Measurement Module
The LM201ANG is appropriate for a precision analog measurement module that combines a single amplifier with external compensation and requires through-hole assembly flexibility. Its 30 nA input bias current and 96 dB common-mode rejection support low-level measurement stages, while the 1 MHz gain-bandwidth product is sufficient for many measurement bandwidths. The non-compensated configuration also permits optimization when the source impedance creates a noise gain above the intended signal gain. Validate offset, bias-current effects, input common-mode range, and stability with the actual transducer and cable. Add input clamping and filtering ahead of the amplifier when the measurement source can exceed its safe operating limits.
推薦
推薦產品摘要
工程參考資料,適用於 LM201ANG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM201AN |
|---|---|---|
| Brand | onsemi | STMicroelectronics |
| Package | 8-PDIP | 8-DIP |
| Amplifier Configuration | Single circuit | Single circuit |
| Product Type | General-purpose operational amplifier | General-purpose operational amplifier |
主要差異化特點
- Externally adjustable compensation (對比LM201AN)
- Established through-hole package (對比LM201ADR2G)
- Defined low-level input characteristics (對比LM201AN)
設計說明
Place the external compensation capacitor directly beside the compensation connection and minimize its trace length. Keep the amplifier feedback components close to the device, use short feedback loops, and separate sensitive input routing from output and compensation nodes. Because the LM201ANG is non-compensated, parasitic board capacitance can alter the compensation network and reduce phase margin. Review the physical layout with the intended source impedance, load, and compensation value.
Do not assume the 1 MHz gain-bandwidth product is the usable closed-loop bandwidth in every circuit. Determine the noise gain, select compensation for that gain, and verify stability across the required load and temperature range. Also observe the stated 10 V to 44 V supply span, 20 V maximum operating voltage, and -25°C to 85°C temperature range. A stable nominal simulation is insufficient if component tolerances or supply variation push the amplifier toward oscillation.
Design the supply rails with the 15 V typical and 20 V maximum operating-voltage conditions in mind. Include adequate bypassing at the device and account for input common-mode limits, output swing, and load-current requirements. The LM201ANG can be used only within its documented supply and signal limits, so rail protection is important when the amplifier receives external laboratory, industrial, or sensor signals. Verify startup and shutdown behavior as well as steady-state regulation.
合規資訊
The component listing identifies LM201ANG as RoHS-compliant, lead-free, and a green electronic component. No separate automotive qualification or REACH declaration is identified for this ordering code.