LM211QDG4 - 115ns Differential Comparator | Texas Instruments
MPN: LM211QDG4 ✓ ActiveLM211QDG4 Overview
A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when the differential input crosses a selected threshold. The LM211 belongs to the comparator hierarchy within analog integrated circuits, where it bridges analog sensing and digital logic. Unlike a general-purpose operational amplifier, its primary purpose is fast binary decision-making rather than linear signal amplification.
The LM211QDG4 accepts a wide supply range, allowing operation from a single 5 V logic rail or from higher single-ended and split-supply systems. Its open-collector output can sink current for driving lamps, relays, and logic-compatible interfaces. The differential inputs permit either inverting or non-inverting threshold configurations, while the strobe control provides a way to disable output-state changes during selected operating intervals.
At 115 ns propagation delay, the LM211 is intended for systems that need faster threshold decisions than general-purpose slow comparators. Its output architecture requires an external pull-up arrangement for conventional open-collector operation. Designers must also account for input common-mode range, output pull-up voltage, and external pull-up current when connecting the device to a particular logic family.
Typical uses include industrial control and monitoring, relay or lamp drive, threshold detection, sensor conditioning interfaces, and mixed analog-to-digital signal chains. The LM211 can also be used in pulse-width and timing-related circuits when comparator response time is important. For systems using differential sensing, the two input pins and the output pull-up network form the core of the interface.
A careful design should preserve input-to-output isolation, route comparator inputs away from high-current switching paths, and select a pull-up resistor that balances rise time with output-current demand. The strobe pin should be driven from a defined logic state rather than left floating, and the power rails must satisfy the device's common-mode and supply requirements.
This product page organizes the electrical characteristics, package details, verified drop-in alternatives, application guidance, and selection trade-offs into a single engineering reference for evaluating the LM211QDG4.
Drop-in alternatives for LM211QDG4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM211QDG4 (same form factor and footprint) — differing in Output Load Capability, Output Type.
LM211DG4
✅ Drop-In📋 Reference alternative (not in catalog)
LM211QD
✅ Drop-InContact for price
View Datasheet →LM211QDRG4
✅ Drop-In📋 Reference alternative (not in catalog)
LM211QDG4 Maximum Ratings & Electrical Characteristics
| Comparator Type | Single differential comparator with strobe |
| Supply Voltage Range | 3.5 V to 30 V |
| Split Supply Operation | ±15 V |
| Propagation Delay | 115 ns |
| Output Type | Open-collector |
| Logic Compatibility | TTL and MOS compatible |
| Input Configuration | Differential |
| Strobe Control | Yes |
| Package | 8-pin SOIC (D) |
| Package Body Width | 3.90 mm (0.154 in) |
| Mounting Type | Surface mount |
| Automotive Qualification | AEC-Q100 |
| Output Load Capability | Lamp or relay drive |
LM211QDG4 Pin Configuration
| Pin 1 | OUT E — Open-collector output emitter |
| Pin 2 | IN− — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V− — Negative supply or ground connection |
| Pin 5 | STROBE — Output strobe control |
| Pin 6 | OUT C — Open-collector output collector |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected |
Typical Applications
LM211QDG4 is suitable for 6 applications: Industrial Threshold Control, Relay and Lamp Drive, Sensor Signal Conditioning, Pulse Width and Timing, Automotive Control Interface, Analog-to-Digital Threshold Front End.
Industrial Threshold Control
The LM211QDG4 fits industrial threshold-control circuits because its differential inputs compare a feedback or reference voltage against a sensed level, while its 115 ns propagation delay provides a relatively quick decision. The open-collector output can operate a relay or lamp interface when the required sink current and voltage ratings are met. In a control board, the comparator can translate an analog condition into a logic event without adding a general-purpose amplifier stage. A pull-up resistor defines the logic high, while the strobe input should be tied to a defined state when continuous monitoring is required. The AEC-Q100 designation also supports designs where automotive qualification is part of the procurement specification.
Recommended
Relay and Lamp Drive
The LM211QDG4 can be used as the decision element in relay or lamp drive circuits because its open-collector output is designed to sink load current and the device supports a wide 3.5 V to 30 V operating range. A pull-up resistor establishes the inactive output level, while the comparator output controls the load path. The 115 ns delay is short enough for many pulse and threshold systems, although relay-coil flyback protection and output-current derating remain essential. Designers should calculate the maximum sink current and voltage from the manufacturer limits before adding a load directly to the output.
Recommended
Sensor Signal Conditioning
The LM211QDG4 is useful at the output of sensor-conditioning circuits where a differential analog signal must be converted into a logic-compatible threshold event. Its differential inputs permit direct comparison of a sensor-derived voltage and a reference, reducing the need for a single-ended input arrangement. The 115 ns propagation delay supports responsive event detection, and the open-collector output simplifies interfacing to TTL or MOS logic through a pull-up. For slow sensors this speed is more than adequate; for fast signals, input capacitance, overdrive, and output rise time require a more complete timing analysis.
Recommended
Pulse Width and Timing
The LM211QDG4 can serve in pulse-width, pulse-detection, and timing circuits because it changes state when the differential input crosses the switching threshold. Its 115 ns propagation delay establishes a relatively fast decision interval, allowing short pulses to be detected more effectively than with a slow comparator. The strobe function can inhibit output transitions during portions of the timing sequence. When using the open-collector output, the pull-up resistance and capacitance of the following logic determine the falling and rising behavior, so timing calculations should include both comparator delay and external output-network delay.
Recommended
Automotive Control Interface
The LM211QDG4’s AEC-Q100 designation makes it relevant to automotive electronic control and monitoring functions requiring a qualified comparator in an 8-pin SOIC package. The differential inputs can monitor a sensor against a threshold, and the 115 ns response supports prompt conversion of the analog condition into a digital event. Its open-collector output can connect to an appropriately protected logic or driver stage, with the pull-up network and external transient protection designed for the vehicle environment. Selection should still include review of temperature grade, supply limits, common-mode range, and load current.
Recommended
Analog-to-Digital Threshold Front End
The LM211QDG4 can provide a fast threshold front end ahead of a digital conversion or monitoring system. A scaled sensor voltage is compared with a reference, and the comparator produces a discrete event when the input difference changes sign. The differential input arrangement is useful when the signal source and reference share a common reference point, while the 115 ns delay allows the decision to track relatively rapid changes. The open-collector output can drive a pull-up and digital input directly when levels and capacitance permit. Layout should keep the input path short, place the pull-up close to the load, and avoid routing sensitive threshold traces beside switching nodes.
Recommended
Recommended Products Summary
Engineering reference data for LM211QDG4 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM211DG4 | LM211QD | LM211QDRG4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Comparator Configuration | Single differential comparator with strobe | Single differential comparator with strobe | Single differential comparator with strobe | Single differential comparator with strobe |
| Supply Voltage Range | 3.5 V to 30 V | 3.5 V to 30 V | 3.5 V to 30 V | 3.5 V to 30 V |
| Propagation Delay | 115 ns | 115 ns | 115 ns | 115 ns |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector |
| Logic Compatibility | TTL and MOS compatible | TTL and MOS compatible | TTL and MOS compatible | TTL and MOS compatible |
| Strobe Control | Yes | Yes | Yes | Yes |
Key Differentiators
- Q-designated automotive ordering configuration (vs LM211DG4)
- Exact tube-packaged orderable MPN (vs LM211QDRG4)
- Differential sensing with integrated strobe control (vs LM211QD)
Design Notes
The LM211QDG4 uses an open-collector output, so a pull-up resistor is required for normal logic-high operation. Select it from the output sink-current limit, the load’s allowable low-level voltage, and the required rise time. Excessive resistance slows the rising edge, while insufficient resistance increases sink current. Do not connect the output to a supply or ground directly; use it as the switched node with the pull-up and load connected from that node to the appropriate rail.
Keep the inverting and non-inverting input traces short, match their surrounding ground references where practical, and keep them away from relay-coil, switch-node, and high-current return paths. Place the output pull-up close to the comparator or receiving logic input to minimize parasitic capacitance. The strobe trace should also be kept short and driven by a defined logic level. These measures reduce noise pickup, output-edge distortion, and unintended threshold transitions.
Confirm that the selected supply arrangement satisfies both the comparator’s supply-voltage limits and its input common-mode range. The LM211 family supports 5 V logic systems as well as ±15 V split supplies, but the allowed input range is not identical to the supply range. Bypass the supply pins with the capacitance specified by the manufacturer’s recommended layout, and keep the return-current path short so switching current from the load does not modulate the comparator reference node.
Estimated timing analysis: with a 115 ns comparator propagation delay, the output-transition timing budget should also include the pull-up network’s rise time and the receiver’s threshold crossing. For a pull-up resistance of 1 kΩ and 50 pF total node capacitance, the estimated 10%–90% output rise time is 110 ns using 2.2RC. Use this only as a design estimate and verify it against the actual load, tolerances, and required system timing.
Compliance Information
AEC-Q100 is identified in the product listing for LM211QDG4. Other environmental and material compliance attributes are not established by the cited product information.