LM224DR2G - 4-Channel 3-32V Op Amp | onsemi
MPN: LM224DR2G ✓ ActiveLM224DR2G Overview
A general-purpose operational amplifier is a voltage-amplified, high-gain active device commonly used for signal conditioning, buffering, comparisons, instrumentation, and closed-loop feedback control. Within the semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories. It provides a practical combination of high open-loop gain, differential input capability, and output-voltage swing, allowing simple external feedback networks to define the closed-loop behavior.
The LM224 series provides four true differential-input amplifiers in one package. Its stated 1 MHz gain-bandwidth product supports general-purpose signal amplification at low and moderate frequencies, while the 0.6 V/us slew rate governs large-signal response. Operation from 3 V to 32 V covers both low-voltage circuits and conventional industrial supply levels. The Mouser listing identifies the LM224DR2G as a low-power quad operational amplifier with a -25°C to 85°C temperature range.
Because each amplifier shares the same package and supply rails, designers can reduce component count and board area in applications requiring several similar channels. The 14-pin SOIC format also supports conventional surface-mount assembly and is compatible with automated inspection and pick-and-place processes. True differential inputs allow each channel to accept signals referenced to the circuit ground without requiring a separate input common-mode arrangement for every channel.
Typical uses include four-channel sensor conditioning, general-purpose signal buffering, instrumentation interfaces, industrial control signal paths, and low-frequency analog measurement systems. Four matched functional channels can simplify a design that needs to process or monitor several related signals. The device is most appropriate when moderate bandwidth, straightforward feedback networks, and wide supply-voltage flexibility matter more than very high speed or very low offset voltage.
Design the bypass capacitance and input network to limit parasitic coupling between adjacent channels. Keep sensitive input traces short, place the supply-bypass capacitor close to the positive and ground pins, and maintain signal returns away from switching nodes. Verify common-mode and output-swing limits against the selected 3 V to 32 V supply before using the amplifier near a rail, because those operating limits determine whether a particular feedback configuration remains linear.
This page combines the manufacturer-family characteristics with package, supply, temperature, frequency, and sourcing information, and adds practical channel-level design guidance for evaluating the LM224DR2G in industrial and instrumentation applications.
Drop-in alternatives for LM224DR2G — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM224DR2G (same form factor and footprint) — differing in Package, AEC-Q100 Qualification, Input Type, Number of Channels, Operating Temperature Range.
LM224DR
✅ Drop-In✓ In Stock
$0.1641 / Unit
View Datasheet →LM224DRG4
✅ Drop-In📋 Reference alternative (not in catalog)
LM124DR
✅ Drop-In📋 Reference alternative (not in catalog)
LM224DR2G Maximum Ratings & Electrical Characteristics
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 circuits |
| Number of Amplifiers | 4 amplifiers |
| Supply Voltage Range | 3 V to 32 V |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/us |
| Input Type | True differential inputs |
| Operating Temperature Range | -25°C to 85°C |
| Package | 14-pin SOIC |
| Mounting Type | Surface mount |
| Quiescent Current Class | Low power |
| Single-Supply Operation | 3 V minimum single-supply operation |
| Maximum Supply Voltage | 32 V |
| Channel Architecture | Quad channel |
| Product Classification | Instrumentation, operational amplifiers, buffer amplifiers |
LM224DR2G 14-pin soic Pin Configuration Guide
Pin configuration for LM224DR2G (14-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LM224DR2G.
Refer to the datasheet for full pin configuration.
Typical Applications
LM224DR2G is suitable for 6 applications: Industrial Sensor Signal Conditioning, Four-Channel Buffering, Instrumentation Amplifier Front End, Low-Frequency Communication Interface, Power and Battery Monitoring, Analog Control and Threshold Conditioning.
Industrial Sensor Signal Conditioning
The LM224DR2G fits industrial sensor-conditioning front ends that amplify several low-frequency analog signals with one package. Its four true differential-input channels can each process a transducer output while sharing a 3 V to 32 V supply, reducing component count compared with four separate single amplifiers. The 1 MHz gain-bandwidth product is appropriate for many resistive sensors, position sensors, and process-control signals that do not require wideband amplification. The principal design consideration is common-mode range: verify that the sensor voltage remains within the amplifier’s operating limits at the selected supply voltage. Keep sensor traces away from switching nodes and use a quiet ground reference to prevent injected current from becoming amplified signal error.
Recommended
Four-Channel Buffering
The LM224DR2G is useful where four low-frequency signals must be buffered before reaching an ADC, logic device, or downstream measurement circuit. Its four amplifiers provide independent unity-gain follower or modest-gain channels in one 14-pin SOIC, while the 0.6 V/us slew rate is suitable for signals that do not require high-speed transitions. A 1 MHz gain-bandwidth product also supports gain settings through the standard inverting and non-inverting feedback networks. Check output-voltage headroom at the chosen supply and avoid operating the output close to a rail when large signal swings are expected. Place the bypass capacitor at the supply pins and route each buffered signal away from the unused high-impedance inputs.
Recommended
Instrumentation Amplifier Front End
The LM224DR2G can form the active portions of a four-channel instrumentation front end when the required bandwidth is moderate. True differential inputs support balanced sensor signals, and the common 3 V to 32 V supply range accommodates both portable and industrial systems. With a 1 MHz gain-bandwidth product, each channel can provide useful closed-loop gain while retaining sufficient bandwidth for slow pressure, temperature, strain, and position measurements. The tradeoff is that the LM224 is a general-purpose amplifier rather than a dedicated low-offset instrumentation amplifier, so resistor matching and input bias behavior may limit accuracy. Use high-value matched feedback networks where practical and verify offset, bias-current, and common-mode requirements against the manufacturer electrical-characteristics table.
Recommended
Low-Frequency Communication Interface
The LM224DR2G can amplify slow communication, control, or interface signals in equipment that does not require GHz-class bandwidth. Its 1 MHz gain-bandwidth product is appropriate for baseband waveform conditioning, receive-buffer tasks, and modest-frequency analog filtering stages. The 0.6 V/us slew rate provides a defined limit for larger voltage transitions, while four channels allow separate transmit, receive, threshold, or monitoring functions on one package. Designers should keep the closed-loop gain low enough to avoid bandwidth reduction around noise-gain peaks and should provide stable feedback components close to the device. Decouple the supply locally and use controlled return paths to prevent digital switching activity from coupling into the analog input nodes.
Recommended
Power and Battery Monitoring
The LM224DR2G can monitor several slowly changing voltages in power-supply or battery-management circuitry because it accepts a 3 V to 32 V supply and includes true differential inputs. A practical arrangement can amplify sensed voltage-difference, output-voltage, and load-current signals for comparison or conversion by downstream circuitry. Its four-channel package reduces the number of separate amplifiers required for multi-point monitoring. The device is not intended for high-side current measurement at high bandwidth, so a suitable current-sense amplifier may be needed where precision current measurement is required. Confirm the common-mode voltage at every monitored node, maintain adequate output headroom, and use short, shielded routing for high-impedance sensing lines.
Recommended
Analog Control and Threshold Conditioning
The LM224DR2G supports general analog control tasks such as error amplification, threshold shaping, and slow closed-loop feedback around a power converter. Its true differential inputs are helpful when the error signal is referenced to another node rather than ground, and the 3 V minimum operating voltage supports low-voltage control systems. With four channels, designers can combine voltage feedback, current feedback, soft-start conditioning, and monitoring functions. The 0.6 V/us slew rate is adequate for many control loops but can become a limiting factor when fast compensation is required. Verify loop stability with the actual feedback network, keep compensation components close to the relevant pins, and avoid routing the compensation node through long traces susceptible to coupling.
Recommended
Recommended Products Summary
Engineering reference data for LM224DR2G — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM224DR | LM224DRG4 | LM124DR |
|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same |
| Number of Amplifiers | 4 | 4 | 4 | 4 |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz | 1.2 MHz |
Key Differentiators
- Wide single-supply operating range (vs LM124DR)
- Four integrated general-purpose channels (vs LM2904PWR)
- Defined general-purpose bandwidth and slew rate (vs LM124DR)
Design Notes
Place the supply-bypass capacitor immediately adjacent to the positive-supply and ground pins, and connect the input and output pins of each channel directly to their feedback components. For a 14-pin SOIC, keep sensitive non-inverting inputs short and away from adjacent output pins. These measures reduce parasitic feedback and coupling between the four amplifier channels, particularly when several channels amplify small sensor signals simultaneously.
Do not assume that a common 14-pin SOIC footprint guarantees identical electrical behavior between amplifier families. Before substituting LM124DR for LM224DR2G, compare input offset voltage, input bias current, common-mode range, output swing, supply current, noise, and temperature limits using the manufacturer data. Also confirm that the feedback values do not create an unstable closed-loop response with the alternate part’s gain-bandwidth and slew-rate characteristics.
Keep the unused inputs of each amplifier in a defined, low-impedance state consistent with the datasheet guidance rather than allowing them to float. Route high-impedance inputs away from clock, relay, motor, and power-converter switching traces. Use a continuous ground plane and a single-point connection strategy for external sensor returns where appropriate, reducing the ground-potential differences that can otherwise appear as input errors in low-level instrumentation circuits.
Compliance Information
No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for the exact LM224DR2G orderable part. The LM224 is an analog integrated circuit and is not an AEC-Q100-qualified automotive device.