LM258DRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments
MPN: LM258DRG4 ✓ ActiveLM258DRG4 Overview
An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify small voltage differences. Within the power-management and signal-processing hierarchy, an operational amplifier acts as a high-gain voltage-feedback block. The LM258 combines two amplifiers in one package, reducing board area while providing common input, output, and supply rails for both channels.
Key features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and operation from a single 3 V supply through split supplies of up to 30 V total. Its -25°C to 85°C operating-temperature range targets general-purpose industrial equipment. The SOIC-8 package also provides a conventional footprint and lead spacing for designs using through-hole-compatible surface-mount assembly methods.
The LM258 architecture is intended for stable operation with conventional feedback networks rather than rail-to-rail input and output operation. Input common-mode range, output swing, supply voltage, load capacitance, and feedback-loop stability must be checked against the application. Its relatively high bandwidth supports general-purpose AC signal amplification, although higher-speed or precision amplifier families may be preferable for demanding instrumentation.
Typical uses include transducer and bridge-amplifier front ends, low-frequency active filters, audio preamplification, voltage followers, comparator-style interfaces, and industrial control signal conditioning. Two amplifiers in one package are especially useful when one channel performs filtering and the second buffers or amplifies the resulting signal. Split-supply operation also supports bipolar sensor signals centered around ground.
For a new layout, place input and output components close to the appropriate pins and maintain a quiet return path for both channels. Check the manufacturer datasheet for common-mode limits, output-swing restrictions, recommended resistor values, and stability requirements before operating near the supply rails or driving capacitive loads.
This page combines the manufacturer specifications with practical design guidance, application selection, and verified pin-compatible alternatives for engineers evaluating the LM258DRG4 in legacy and new analog signal-chain designs.
Drop-in alternatives for LM258DRG4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM258DRG4 (same form factor and footprint) — differing in Amplifier Type, Slew Rate, Mounting Type, Gain-Bandwidth Product, Number of Amplifiers.
LM2902N/PB
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →LM258DT
✅ Drop-InContact for price
View Datasheet →TSH22IDT
✅ Drop-In📋 Reference alternative (not in catalog)
TSB7192IDT
✅ Drop-In📋 Reference alternative (not in catalog)
LM258DRG4 Maximum Ratings & Electrical Characteristics
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 amplifiers |
| Maximum Supply Voltage | 30 V |
| Supply Voltage Range | ±1.5 V to ±16 V |
| Single-Supply Minimum Voltage | 3 V |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Operating Temperature Range | -25°C to 85°C |
| Package | 8-pin SOIC |
| Mounting Type | Surface mount |
| Unity-Gain Bandwidth | 700 kHz |
| RoHS Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
LM258DRG4 Pin Configuration
| Pin 1 | OUT1 — Output of amplifier 1 |
| Pin 2 | -IN1 — Inverting input of amplifier 1 |
| Pin 3 | +IN1 — Non-inverting input of amplifier 1 |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | +IN2 — Non-inverting input of amplifier 2 |
| Pin 6 | -IN2 — Inverting input of amplifier 2 |
| Pin 7 | OUT2 — Output of amplifier 2 |
| Pin 8 | V+ — Positive supply connection |
Typical Applications
LM258DRG4 is suitable for 6 applications: Industrial Sensor Signal Conditioning, Audio Preamplifier, Active Filter and Control Loops, Voltage Buffer Interface, Power Supply Feedback, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM258DRG4 is appropriate for conditioning low-level signals from industrial sensors because it combines two amplifiers, a 700 kHz gain-bandwidth product, and operation from a single 3 V supply through ±16 V split supplies. One channel can amplify a sensor output while the second buffers the result or provides gain before an analog-to-digital converter. The -25°C to 85°C range supports general-purpose industrial environments. Designers should confirm that the sensor voltage remains within the common-mode input range and that the output swing leaves adequate headroom for the converter reference. A 100 nF bypass capacitor near the supply pin and short feedback paths help preserve signal integrity.
Recommended
Audio Preamplifier
The LM258DRG4 can serve in a low-frequency audio preamplifier when the design does not require rail-to-rail operation. Its 700 kHz gain-bandwidth product supports moderate-bandwidth gain stages, while the 0.3 V/µs slew rate helps preserve large-signal transitions compared with very slow general-purpose amplifiers. The dual package allows one channel to provide input gain and the other to drive a filter or output buffer. The 30 V maximum supply rating permits split-supply operation for bipolar audio signals, and the -25°C to 85°C range suits many industrial or consumer audio products. Output swing and load capability must be checked before driving the intended speaker or line stage.
Recommended
Active Filter and Control Loops
The LM258DRG4 is well suited to active-filter and basic control-loop designs operating well below its 700 kHz gain-bandwidth product. Two independent channels allow implementation of a second-order active-filter stage followed by an amplifier, integrator, or buffer. Operation from 3 V single supply supports compact control electronics, while ±16 V split supplies provide headroom for bipolar signals. Stable operation depends on the selected noise gain, component tolerances, and capacitive loading, so use the typical application circuits in the Texas Instruments LM258 manufacturer datasheet. Place feedback components close to the relevant pins and provide a low-impedance ground return to reduce oscillation risk and channel interaction.
Recommended
Voltage Buffer Interface
The LM258DRG4 can implement unity-gain voltage buffers when the source impedance is compatible with the amplifier's input-current characteristics and the required signal bandwidth is below 700 kHz. This configuration isolates sensor, divider, or reference outputs from downstream loading. Two channels in one 8-pin SOIC simplify dual-buffer implementations, while the 30 V supply rating supports both low-voltage and bipolar interface systems. Because the LM258 is not specified as rail-to-rail, the buffered voltage must remain inside the common-mode input range, and the output must maintain sufficient swing distance from the supply rails. Verify capacitive-load stability when driving long cables or sampled input networks.
Recommended
Power Supply Feedback
The LM258DRG4 can monitor a power rail through a resistive divider and amplify the difference from a reference for supervisory or power-control circuitry. Its 30 V maximum supply rating allows operation near the upper end of a 24 V industrial rail when suitable input attenuation and operating limits are maintained. A 700 kHz gain-bandwidth product is sufficient for many slow feedback loops, although loop compensation must be checked against the power-stage dynamics. The dual arrangement can amplify the feedback error on one channel and buffer or invert it on the other. Use a low-impedance reference, keep divider currents sufficient relative to input bias current, and route the feedback node away from switching nodes.
Recommended
Portable Instrumentation
The LM258DRG4 is useful in portable instrumentation that requires two analog channels, a modest bandwidth, and operation from a compact supply. A 3 V single-supply configuration reduces power-supply complexity, while the -25°C to 85°C range accommodates many portable measurement products. One channel can amplify a transducer signal and the second can compensate the following stage or implement gain. The 0.3 V/µs slew rate supports moderate-amplitude, low-frequency waveforms but does not make the device appropriate for high-frequency precision acquisition without additional analysis. Confirm common-mode range, output swing, input bias current, noise, and power consumption against the instrumentation accuracy specification before finalizing the design.
Recommended
Recommended Products Summary
Engineering reference data for LM258DRG4 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM2902N/PB | LM258DT | TSH22IDT | TSB7192IDT |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers |
Key Differentiators
- Maintains the established Texas Instruments LM258 electrical family in the exact 8-pin SOIC configuration (vs LM258DT)
- Higher maximum supply rating than the lower-voltage rail-to-rail STMicroelectronics alternatives (vs TSB7192IDT)
- Single 3 V operation provides supply-design flexibility (vs TSH22IDT)
Design Notes
Place each input, feedback component, and output component close to the pins of the channel that uses it. Keep the two channels' high-impedance input nodes physically separated to reduce crosstalk. Route the positive and negative supply traces directly to pins 8 and 4, place the supply-bypass capacitor at the device, and connect its return through a short, low-impedance path. These steps are particularly important in sensor-conditioning boards where small input voltages can otherwise couple directly from the output circuitry.
Do not assume that a 30 V maximum supply rating permits rail-to-rail signal operation. The LM258's usable input common-mode range and output swing are narrower than its supply rails, and the exact limits vary with supply voltage and output current. Check both amplifier channels against the largest expected input and the minimum expected load. Also verify whether the selected alternative offers rail-to-rail behavior, because a different input range can make a footprint-compatible replacement electrically unsuitable.
Use the typical application circuits in the Texas Instruments LM258 manufacturer datasheet when selecting feedback resistors and compensation. A feedback resistor that is too small can increase output-current demand, while excessive capacitance at the output can cause instability. For filters, calculate the closed-loop bandwidth from the actual noise gain rather than using the 700 kHz gain-bandwidth product as the operating limit. Decouple dual-supply designs according to the manufacturer's grounding recommendations and keep switching-regulator traces away from the input nodes.
Use the supply voltage required by the signal, not the maximum 30 V rating, because the output swing and input common-mode range change with the operating voltage. Decouple pin 8 to ground for single-supply operation and both supply pins to ground for split-supply operation as required by the circuit configuration. Confirm that upstream supply ripple remains within the device's rejection requirements and that the source can provide the current demanded by the feedback network and load.
Compliance Information
The manufacturer product page and datasheet identify the LM258 family, but the listed pages do not provide extractable LM258DRG4-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose industrial operational amplifier.