Texas Instruments

LM258DRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments

부품 번호: LM258DRG4 ✓ 활성
30 V Vdss 8-pin SOIC Package
MOQ: 1 |

LM258DRG4 개요

The Texas Instruments LM258DRG4 is a dual general-purpose operational amplifier with a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate, packaged in an 8-pin SOIC. The device provides two independent amplifiers and supports single-supply or split-supply operation across ±1.5 V to ±16 V, making it suitable for industrial control, sensor conditioning, and audio signal-chain applications.

An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify small voltage differences. Within the power-management and signal-processing hierarchy, an operational amplifier acts as a high-gain voltage-feedback block. The LM258 combines two amplifiers in one package, reducing board area while providing common input, output, and supply rails for both channels.

Key features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and operation from a single 3 V supply through split supplies of up to 30 V total. Its -25°C to 85°C operating-temperature range targets general-purpose industrial equipment. The SOIC-8 package also provides a conventional footprint and lead spacing for designs using through-hole-compatible surface-mount assembly methods.

The LM258 architecture is intended for stable operation with conventional feedback networks rather than rail-to-rail input and output operation. Input common-mode range, output swing, supply voltage, load capacitance, and feedback-loop stability must be checked against the application. Its relatively high bandwidth supports general-purpose AC signal amplification, although higher-speed or precision amplifier families may be preferable for demanding instrumentation.

Typical uses include transducer and bridge-amplifier front ends, low-frequency active filters, audio preamplification, voltage followers, comparator-style interfaces, and industrial control signal conditioning. Two amplifiers in one package are especially useful when one channel performs filtering and the second buffers or amplifies the resulting signal. Split-supply operation also supports bipolar sensor signals centered around ground.

For a new layout, place input and output components close to the appropriate pins and maintain a quiet return path for both channels. Check the manufacturer datasheet for common-mode limits, output-swing restrictions, recommended resistor values, and stability requirements before operating near the supply rails or driving capacitive loads.

This page combines the manufacturer specifications with practical design guidance, application selection, and verified pin-compatible alternatives for engineers evaluating the LM258DRG4 in legacy and new analog signal-chain designs.

드롭인 대체품: LM258DRG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: LM258DRG4 (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Slew Rate, Mounting Type, Gain-Bandwidth Product, Number of Amplifiers.

Texas Instruments
Amplifier Type: General Purpose
Slew Rate: 0.3 V/us
Number of Amplifiers: 2 circuits
비교 대상: LM258DRG4 →
STMicroelectronics
Amplifier Type: Dual low-power operational amplifier
Slew Rate: 0.6 V/us
비교 대상: LM258DRG4 →
Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier
Mounting Type: Through-hole
Gain-Bandwidth Product: 1 MHz

LM2902N/PB

✅ 드롭인 ⚠️ 사양 미검증
Texas Instruments
📦 8-pin SOIC
4 · 26 V · 1 MHz · Quad general-purpose operational amplifier · Independent, high-gain, internally frequency-compensated · Single-supply operation · 14-pin DIP · DIP-14

가격 문의

데이터시트 보기 →

LM258DT

✅ 드롭인
STMicroelectronics
📦 8-pin SOIC
Dual low-power operational amplifier · 2 amplifiers · 2 circuits · 3 V to 30 V · 1.1 MHz · 0.6 V/us · 100 dB · 500 uA

가격 문의

데이터시트 보기 →

TSH22IDT

✅ 드롭인
📦 8-pin SOIC
Uses the same 8-pin SOIC dual-op-amp arrangement but supports a lower-voltage family focused on rail-to-rail operation, approximately 30% below the 30 V supply ceiling

📋 참조 대체품 (카탈로그에 없음)

TSB7192IDT

✅ 드롭인
📦 8-pin SOIC
Shares the 8-pin SOIC dual-op-amp layout but has a lower-voltage rail-to-rail focus, approximately 30% below the 30 V maximum supply rating

📋 참조 대체품 (카탈로그에 없음)

LM258DRG4 최대 정격 & 전기적 특성

Amplifier Type Dual general-purpose operational amplifier
Number of Amplifiers 2 amplifiers
Maximum Supply Voltage 30 V
Supply Voltage Range ±1.5 V to ±16 V
Single-Supply Minimum Voltage 3 V
Gain-Bandwidth Product 700 kHz
Slew Rate 0.3 V/µs
동작 온도 범위 -25°C to 85°C
패키지 8-pin SOIC
실장 유형 Surface mount
Unity-Gain Bandwidth 700 kHz
RoHS 상태 unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

LM258DRG4 핀 구성

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
핀 1 OUT1 — Output of amplifier 1
핀 2 -IN1 — Inverting input of amplifier 1
핀 3 +IN1 — Non-inverting input of amplifier 1
핀 4 V- — Negative supply connection
핀 5 +IN2 — Non-inverting input of amplifier 2
핀 6 -IN2 — Inverting input of amplifier 2
핀 7 OUT2 — Output of amplifier 2
핀 8 V+ — Positive supply connection

일반적인 애플리케이션

LM258DRG4 적합 용도: 6 애플리케이션s: Industrial Sensor Signal Conditioning, Audio Preamplifier, Active Filter and Control Loops, Voltage Buffer Interface, Power Supply Feedback, Portable Instrumentation.

🏭

Industrial Sensor Signal Conditioning

The LM258DRG4 is appropriate for conditioning low-level signals from industrial sensors because it combines two amplifiers, a 700 kHz gain-bandwidth product, and operation from a single 3 V supply through ±16 V split supplies. One channel can amplify a sensor output while the second buffers the result or provides gain before an analog-to-digital converter. The -25°C to 85°C range supports general-purpose industrial environments. Designers should confirm that the sensor voltage remains within the common-mode input range and that the output swing leaves adequate headroom for the converter reference. A 100 nF bypass capacitor near the supply pin and short feedback paths help preserve signal integrity.

🎧

Audio Preamplifier

The LM258DRG4 can serve in a low-frequency audio preamplifier when the design does not require rail-to-rail operation. Its 700 kHz gain-bandwidth product supports moderate-bandwidth gain stages, while the 0.3 V/µs slew rate helps preserve large-signal transitions compared with very slow general-purpose amplifiers. The dual package allows one channel to provide input gain and the other to drive a filter or output buffer. The 30 V maximum supply rating permits split-supply operation for bipolar audio signals, and the -25°C to 85°C range suits many industrial or consumer audio products. Output swing and load capability must be checked before driving the intended speaker or line stage.

🔧

Active Filter and Control Loops

The LM258DRG4 is well suited to active-filter and basic control-loop designs operating well below its 700 kHz gain-bandwidth product. Two independent channels allow implementation of a second-order active-filter stage followed by an amplifier, integrator, or buffer. Operation from 3 V single supply supports compact control electronics, while ±16 V split supplies provide headroom for bipolar signals. Stable operation depends on the selected noise gain, component tolerances, and capacitive loading, so use the typical application circuits in the Texas Instruments LM258 manufacturer datasheet. Place feedback components close to the relevant pins and provide a low-impedance ground return to reduce oscillation risk and channel interaction.

⚡

Voltage Buffer Interface

The LM258DRG4 can implement unity-gain voltage buffers when the source impedance is compatible with the amplifier's input-current characteristics and the required signal bandwidth is below 700 kHz. This configuration isolates sensor, divider, or reference outputs from downstream loading. Two channels in one 8-pin SOIC simplify dual-buffer implementations, while the 30 V supply rating supports both low-voltage and bipolar interface systems. Because the LM258 is not specified as rail-to-rail, the buffered voltage must remain inside the common-mode input range, and the output must maintain sufficient swing distance from the supply rails. Verify capacitive-load stability when driving long cables or sampled input networks.

⚡

Power Supply Feedback

The LM258DRG4 can monitor a power rail through a resistive divider and amplify the difference from a reference for supervisory or power-control circuitry. Its 30 V maximum supply rating allows operation near the upper end of a 24 V industrial rail when suitable input attenuation and operating limits are maintained. A 700 kHz gain-bandwidth product is sufficient for many slow feedback loops, although loop compensation must be checked against the power-stage dynamics. The dual arrangement can amplify the feedback error on one channel and buffer or invert it on the other. Use a low-impedance reference, keep divider currents sufficient relative to input bias current, and route the feedback node away from switching nodes.

🧩

Portable Instrumentation

The LM258DRG4 is useful in portable instrumentation that requires two analog channels, a modest bandwidth, and operation from a compact supply. A 3 V single-supply configuration reduces power-supply complexity, while the -25°C to 85°C range accommodates many portable measurement products. One channel can amplify a transducer signal and the second can compensate the following stage or implement gain. The 0.3 V/µs slew rate supports moderate-amplitude, low-frequency waveforms but does not make the device appropriate for high-frequency precision acquisition without additional analysis. Confirm common-mode range, output swing, input bias current, noise, and power consumption against the instrumentation accuracy specification before finalizing the design.

What is the operating voltage of LM258DRG4?
The LM258DRG4 operates from a single 3 V supply through split supplies of ±16 V, equivalent to a maximum total rating of 30 V. According to the Texas Instruments LM258 manufacturer datasheet, the device is intended for general-purpose industrial operation from -25°C to 85°C. Designers should also observe the input common-mode range and output-swing limits, which are narrower than the full supply rating.
What are the key specifications of LM258DRG4 that engineers should know?
The LM258DRG4 is a dual operational amplifier with a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, 30 V maximum supply voltage, and -25°C to 85°C operating-temperature range. The Texas Instruments manufacturer datasheet identifies the device as an industry-standard dual operational amplifier in an 8-pin SOIC package. Both channels share supply pins, making it useful for paired signal-processing functions.
Where can I download the LM258DRG4 datasheet PDF?
The official LM258DRG4 datasheet is available through Texas Instruments at https://www.ti.com/lit/gpn/LM258. The document covers the LM258 family and includes electrical characteristics, pin configuration, typical application circuits, and ordering information. Use the package-specific pin description when assigning PCB nets because the LM258 family includes several temperature and packaging configurations.
Where is the LM258DRG4 pinout located?
The LM258DRG4 pinout is shown in the Texas Instruments LM258 manufacturer datasheet at https://www.ti.com/lit/gpn/LM258. For the 8-pin SOIC configuration, pins 1 and 7 are the two outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are non-inverting inputs, pin 4 is the negative supply, and pin 8 is the positive supply. Confirm the selected ordering code before laying out a new PCB.
What can replace the LM258DRG4?
The LM258DT from STMicroelectronics is a direct 8-pin SOIC alternative for designs based on the conventional dual-op-amp pinout, with the same 30 V-class supply capability and 700 kHz-class bandwidth indicated by the product listing. TSH22IDT and TSB7192IDT are also identified as SO-8 alternatives, although their electrical limits must be checked for rail-to-rail, supply-voltage, and stability differences before substitution.
Is LM258DRG4 the same as LM258DT?
The LM258DRG4 and STMicroelectronics LM258DT are presented as comparable 8-pin dual operational amplifiers, but they are not identical order codes from the same manufacturer. Both use the conventional SO-8 operational-amplifier arrangement and operate from split supplies of ±1.5 V to ±16 V. Verify input bias current, offset voltage, common-mode range, output swing, and stability before exchanging parts.
LM258DRG4 vs LM258DT - which is better for industrial control?
Choose the LM258DRG4 when Texas Instruments qualification, documentation, and sourcing continuity are priorities for a legacy industrial design. The LM258DT can be attractive for a new design when its specific electrical characteristics, automotive or industrial qualification, and availability better match the project. Both provide dual amplifiers in 8-pin SOIC packages, but temperature grade and parametric details must be checked for the exact ordering code.
When should I choose LM258DRG4 instead of TSH22IDT?
Choose the LM258DRG4 when the design specifically targets the Texas Instruments LM258 electrical behavior, established source code, and conventional dual-op-amp pinout. Choose TSH22IDT when its lower rail-to-rail operating voltage or other family-specific characteristics offer a functional benefit and its datasheet confirms the required common-mode range, output swing, and stability. Both use 8-pin SOIC packages, but package equality alone does not prove full interchangeability.
Is LM258DRG4 suitable for low-frequency filter and audio circuits?
The LM258DRG4 is suitable for many low-frequency filter and audio preamplifier circuits because its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful small-signal bandwidth. According to the Texas Instruments LM258 manufacturer datasheet, the device is an industry-standard dual amplifier. Avoid designs requiring rail-to-rail input or output operation, and verify output swing at the selected supply voltage and load.
Does LM258DRG4 support single and split-supply operation?
The LM258DRG4 supports single-supply operation from 3 V and split-supply operation from ±1.5 V to ±16 V. Texas Instruments describes the LM258 as a dual, 30 V operational amplifier for general-purpose industrial applications. In a single-supply circuit, the input and output signal levels must remain inside the specified common-mode and output-swing ranges rather than approaching the supply rails.
What is the LM258DRG4 slew rate and gain-bandwidth product?
The LM258DRG4 has a 0.3 V/µs slew rate and a 700 kHz gain-bandwidth product. The Texas Instruments product description identifies a 700 kHz dual operational amplifier, while the LM258DRG4 specification listing gives the 0.3 V/µs slew rate. These figures support general-purpose low-frequency amplification but may be insufficient for wide-band, precision, or high-output-swing applications.
Where can I buy LM258DRG4 and check current lead time?
Use the Request a Quote form on this page to request LM258DRG4 availability, current pricing, and lead time for the required quantity. The Texas Instruments product page identifies LM258 as a 30 V, 700 kHz dual operational amplifier, while the exact LM258DRG4 ordering code specifies the 8-pin SOIC configuration. Confirm the package, temperature grade, and reel quantity when placing the order.
Is LM258DRG4 in stock?
The LM258DRG4 is listed as in stock by one component supplier, while stock levels and delivery schedules can change without notice. Use the Request a Quote form on this page for the current quantity required by your build. Include the SOIC-8 ordering code and any acceptable alternative manufacturers so sourcing can confirm the exact configuration rather than a related LM258 package variant.
What is the lead time for LM258DRG4?
Contact XAIPART through the Request a Quote form on this page for the current LM258DRG4 lead time and minimum order quantity. The Texas Instruments LM258 product page confirms the family and its 30 V, 700 kHz characteristics, but a manufacturing schedule and stock position must be confirmed for each order. Include your required date, forecast quantity, and acceptable trace-and-packing requirements.
Is LM258DRG4 compliant with RoHS and REACH?
The RoHS and REACH status of LM258DRG4 cannot be confirmed from the product pages listed for this ordering code, so both should be treated as unknown until checked against the current manufacturer compliance documentation. The Texas Instruments product page and manufacturer datasheet are the appropriate sources for package, quality, and environmental statements. If the compliance declaration is required for procurement, request the declaration tied to the exact orderable part number.

엔지니어링 참조 데이터: LM258DRG4 — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the LM258DRG4 for a new or legacy design that specifically depends on the Texas Instruments LM258 behavior, uses the conventional 8-pin SOIC dual-op-amp pinout, and operates from 3 V through ±16 V split supplies. Its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate fit general-purpose signal conditioning, active filtering, buffering, and low-frequency audio stages. Choose LM258DT when its manufacturer-specific offset, bias-current, qualification, and sourcing characteristics better fit the project; its 30 V-class electrical positioning is closely aligned. TSH22IDT or TSB7192IDT may be useful when lower-voltage or rail-to-rail operation is beneficial, but their narrower supply ceiling and different input/output characteristics require a fresh stability and signal-range review. For every alternative, confirm the exact pin functions, common-mode range, output swing, capacitive-load behavior, temperature grade, and required decoupling before releasing a replacement order.

대체품과의 비교

파라미터 이 제품 LM2902N/PB LM258DT TSH22IDT TSB7192IDT
Brand Texas Instruments Texas Instruments STMicroelectronics STMicroelectronics STMicroelectronics
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Number of Amplifiers 2 amplifiers 2 amplifiers 2 amplifiers 2 amplifiers 2 amplifiers

주요 차별점

  • Maintains the established Texas Instruments LM258 electrical family in the exact 8-pin SOIC configuration (vs LM258DT)
  • Higher maximum supply rating than the lower-voltage rail-to-rail STMicroelectronics alternatives (vs TSB7192IDT)
  • Single 3 V operation provides supply-design flexibility (vs TSH22IDT)

설계 노트

Place each input, feedback component, and output component close to the pins of the channel that uses it. Keep the two channels' high-impedance input nodes physically separated to reduce crosstalk. Route the positive and negative supply traces directly to pins 8 and 4, place the supply-bypass capacitor at the device, and connect its return through a short, low-impedance path. These steps are particularly important in sensor-conditioning boards where small input voltages can otherwise couple directly from the output circuitry.

Do not assume that a 30 V maximum supply rating permits rail-to-rail signal operation. The LM258's usable input common-mode range and output swing are narrower than its supply rails, and the exact limits vary with supply voltage and output current. Check both amplifier channels against the largest expected input and the minimum expected load. Also verify whether the selected alternative offers rail-to-rail behavior, because a different input range can make a footprint-compatible replacement electrically unsuitable.

Use the typical application circuits in the Texas Instruments LM258 manufacturer datasheet when selecting feedback resistors and compensation. A feedback resistor that is too small can increase output-current demand, while excessive capacitance at the output can cause instability. For filters, calculate the closed-loop bandwidth from the actual noise gain rather than using the 700 kHz gain-bandwidth product as the operating limit. Decouple dual-supply designs according to the manufacturer's grounding recommendations and keep switching-regulator traces away from the input nodes.

Use the supply voltage required by the signal, not the maximum 30 V rating, because the output swing and input common-mode range change with the operating voltage. Decouple pin 8 to ground for single-supply operation and both supply pins to ground for split-supply operation as required by the circuit configuration. Confirm that upstream supply ripple remains within the device's rejection requirements and that the source can provide the current demanded by the feedback network and load.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The manufacturer product page and datasheet identify the LM258 family, but the listed pages do not provide extractable LM258DRG4-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose industrial operational amplifier.

데이터 검증일: 2026-11-15 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

LM258DRG4 datasheet LM258DRG4 pinout LM258DRG4 datasheet pdf LM258DRG4 equivalent LM258DRG4 replacement LM258DRG4 cross reference LM258DRG4 vs LM258DT LM258DRG4 SOIC-8 footprint LM258DRG4 price LM258DRG4 stock Texas Instruments LM258DRG4 LM258 dual 700 kHz amplifier LM258DRG4 industrial signal conditioning LM258DRG4 application circuit

관련 부품 & 용어

Texas Instruments LM258 LM258DRG4 LM2902N/PB LM258DT TSH22IDT TSB7192IDT STMicroelectronics operational amplifier dual operational amplifier voltage-feedback amplifier analog integrated circuit signal conditioning active filter common-mode input range output swing gain-bandwidth product slew rate single-supply operation split-supply operation 8-pin SOIC SOIC family surface-mount package industrial control audio preamplifier
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기