Texas Instruments

LM2901DG4 - 30V Quad Differential Comparator | Texas Instruments

MPN: LM2901DG4 ✓ Active
30 V Vdss 3.5 nA Id 14-pin SOIC, 3.90 mm width Package
MOQ: 1 |

LM2901DG4 Overview

The Texas Instruments LM2901DG4 is a 30 V quad differential comparator containing four independent comparison channels, an input common-mode range that includes ground, and open-collector outputs in a 14-pin SOIC package. Its maximum-rated supply voltage reaches 38 V, while the published operating supply range is 2 V to 36 V. The device provides low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, and low supply current of 200 µA per comparator.

A differential comparator is a semiconductor that compares two input voltages and changes its output when one input becomes higher than the other. The LM2901 belongs to the comparator hierarchy within analog integrated circuits, where it provides a simple binary decision function for control, sensing, and protection circuits. Each of its four channels is electrically independent, allowing one package to perform four separate threshold comparisons without requiring four single-comparator packages.

The LM2901 supports single-supply or dual-supply operation, making it adaptable to systems using 2 V to 36 V rails. Its differential input voltage range can equal the maximum-rated supply voltage, and its open-collector outputs allow wired-AND behavior when an external pull-up is used. The low 200 µA supply current per comparator is useful in battery-operated equipment, while the 0.37 mV input offset helps preserve accuracy in low-level sensing applications.

The 300 ns response time supports comparisons in switching and control loops where propagation delay matters. Outputs are compatible with TTL, MOS, and CMOS logic, which simplifies interfacing with microcontroller input pins, logic gates, relay drivers, and open-collector devices. Unlike an op-amp configured as a comparator, the LM2901 is intended specifically for open-loop threshold comparison and does not include the feedback network normally associated with linear amplification.

Typical uses include industrial sensor threshold detection, overvoltage and undervoltage monitoring, battery discharge indication, temperature-limit switching, motor or actuator control, and four-channel digital sensing. The common-mode input range that includes ground is particularly useful for detecting signals near 0 V. In systems with multiple open-collector outputs, an external pull-up resistor is required to establish a valid high output level.

Design the PCB with short comparator input traces, a solid ground reference, and careful separation between sensitive input nodes and output or pull-up paths. The open-collector output must never remain connected directly to a supply rail without a suitable pull-up. Confirm actual output sink current, input common-mode limits, and supply behavior against the manufacturer datasheet for the exact operating condition.

This product page combines the LM2901DG4 electrical specifications, a complete 14-SOIC pin map, same-footprint alternatives, and application guidance. It is designed to help engineers make a compatibility decision quickly while still validating the final circuit against the manufacturer datasheet.

Drop-in alternatives for LM2901DG4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with LM2901DG4 (same form factor and footprint) — differing in Package, Comparator Type, Logic Compatibility, Supply Current, Output Type.

Texas Instruments
Package: 14-SOIC, 0.154 inch width, 3.90 mm width
Logic Compatibility: TTL, MOS, and CMOS compatible with pull-up
Supply Current: 200 uA per comparator
Compare with LM2901DG4 →
onsemi
Package: 14-SOIC
Comparator Type: General Purpose
Supply Current: 1 mA
Compare with LM2901DG4 →
onsemi
Package: 14-pin SOIC
Comparator Type: Quad differential voltage comparator
Compare with LM2901DG4 →
onsemi
Package: 14-pin SOIC
Logic Compatibility: CMOS and TTL
Compare with LM2901DG4 →

LM2901DR2

✅ Drop-In
onsemi
📦 14-pin SOIC
Quad differential voltage comparator · 4 channels · 3 V to 36 V · 25 nA typical · Open collector · Single supply or split supply

Contact for price

View Datasheet →

LM2901DRG4

✅ Drop-In
📦 14-pin SOIC
Same Texas Instruments LM2901 family and 14-SOIC footprint; stated 7 mV maximum offset and 1.3 µs response time differ by 0%.

📋 Reference alternative (not in catalog)

LM2901DE4

✅ Drop-In
Texas Instruments
📦 14-pin SOIC
Quad differential comparator · 4 channels · Open-collector · 2 V to 30 V · 38 V · 0.37 mV typical · 3.5 nA · 200 uA per comparator

Contact for price

View Datasheet →

LM2901DR2G

✅ Drop-In
onsemi
📦 14-pin SOIC
Quad differential comparator · 4 channels · 3 V to 36 V · -40°C to +105°C · Open collector · CMOS and TTL · 14-pin SOIC · Surface mount

Contact for price

View Datasheet →

LM2901DG

✅ Drop-In
onsemi
📦 14-pin SOIC
General Purpose · 4 · 3 V to 36 V · ±1.5 V to ±18 V · 1.3 us · Open Collector · CMOS, TTL · 1 mA

Contact for price

View Datasheet →

LM2901DG4 Maximum Ratings & Electrical Characteristics

Comparator Type Quad differential comparator
Number of Channels 4 channels
Nominal Supply Voltage 30 V
Operating Supply Voltage Range 2 V to 36 V
Maximum Supply Voltage 38 V
Input Offset Voltage 0.37 mV
Input Bias Current 3.5 nA
Supply Current 200 µA per comparator
Response Time 300 ns
Output Type Open collector
Common-Mode Input Range Includes ground
Differential Input Voltage Range Up to ±38 V
Logic Compatibility TTL, MOS, and CMOS
ESD Rating, HBM 2 kV
Package 14-pin SOIC, 3.90 mm width
Mounting Type Surface mount
RoHS Status unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

LM2901DG4 Pin Configuration

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
Pin 1 OUT2 — Open-collector output for comparator channel 2
Pin 2 IN2- — Inverting input for comparator channel 2
Pin 3 IN2+ — Noninverting input for comparator channel 2
Pin 4 GND — Ground connection
Pin 5 IN1+ — Noninverting input for comparator channel 1
Pin 6 IN1- — Inverting input for comparator channel 1
Pin 7 OUT1 — Open-collector output for comparator channel 1
Pin 8 OUT3 — Open-collector output for comparator channel 3
Pin 9 IN3- — Inverting input for comparator channel 3
Pin 10 IN3+ — Noninverting input for comparator channel 3
Pin 11 V+ — Positive supply connection
Pin 12 OUT4 — Open-collector output for comparator channel 4
Pin 13 IN4- — Inverting input for comparator channel 4
Pin 14 IN4+ — Noninverting input for comparator channel 4

Typical Applications

LM2901DG4 is suitable for 6 applications: Industrial Sensor Threshold Detection, Battery Pack Monitoring, Overvoltage and Undervoltage Protection, Temperature Limit Control, Motor and Actuator Control, Digital Control Logic Interface.

🏭

Industrial Sensor Threshold Detection

The LM2901DG4 fits industrial sensor interfaces that require four independent threshold decisions in a compact circuit. Its 300 ns response time allows the comparator channels to respond quickly to changing sensor signals, while the common-mode input range that includes ground supports inputs near 0 V. Each channel compares a scaled sensor voltage against a reference and produces an open-collector state for an alarm, interlock, or controller input. Add positive feedback for adjustable hysteresis when noise or slow signal transitions could otherwise cause repeated switching. Because every output is open collector, connect an appropriate pull-up to the logic rail and account for its sink-current requirement.

⚡

Battery Pack Monitoring

The LM2901DG4 can monitor several battery-related voltages in portable or energy-storage systems using its four independent differential channels. Its 2 V to 36 V operating supply range accommodates many pack voltage levels, and the 200 µA supply current per comparator limits the burden introduced by the comparator itself. A resistor divider can translate each cell or pack signal into the comparator input range, allowing the device to flag undervoltage, overvoltage, or abnormal conditions. The common-mode range including ground is useful for detecting low battery states. Use resistor tolerances and input filtering to prevent normal cell variation from creating false transitions, and pull each open-collector output up to the monitoring system’s logic rail.

🛡️

Overvoltage and Undervoltage Protection

The LM2901DG4 is well suited to independent overvoltage and undervoltage protection functions in industrial and automotive-adjacent control systems. Each differential comparator channel can compare a divided supply signal with an internal reference, producing a fault indication when the monitored voltage crosses the selected threshold. The 38 V maximum-rated supply voltage provides headroom for systems operating near the upper end of the 2 V to 36 V range, while the 300 ns response time supports prompt fault signaling. Because an open-collector output can sink current rather than source it, use a pull-up and design the shutdown path so a wiring fault cannot unintentionally disable the protected load. Hysteresis is recommended whenever supply ripple could otherwise oscillate the fault output.

🌡️

Temperature Limit Control

The LM2901DG4 can implement several temperature-limit channels when each temperature sensor is conditioned into a voltage compatible with the comparator inputs. Its low 3.5 nA input bias current reduces loading on high-impedance sensor networks, while the 0.37 mV input offset helps preserve threshold accuracy. A 300 ns response time allows the comparator to react quickly once a sensor crosses its limit, making the device suitable for thermal cutoff, fan control, or thermal-shutdown signaling. Use the external input and output network to establish the actual trip point and hysteresis. Keep sensitive sensor traces away from switching nodes and provide a pull-up on every open-collector output used by the controller.

⚙️

Motor and Actuator Control

The LM2901DG4 can provide inexpensive limit detection and interlock decisions around motors, relays, and electromechanical actuators. Four differential channels allow position, current-sense, or command signals to be checked independently, and the 300 ns response time is useful when the control system must react quickly to a limit transition. The open-collector output can participate in wired logic or drive an appropriate interface stage rather than powering a motor directly. For inductive loads, use the open-collector stage only within its specified sink-current and voltage limits, or add a suitable driver and flyback protection. Slow input edges or excessive noise should be handled with filtering and hysteresis so the comparator does not generate repeated actuator commands.

🖥️

Digital Control Logic Interface

The LM2901DG4 is appropriate for converting analog decision points into TTL, MOS, or CMOS-compatible digital events. Its four differential channels can compare command, feedback, and status voltages, while the open-collector outputs support wired-AND behavior when a common pull-up is used. The output family’s compatibility simplifies connection to controller inputs, although the actual high level always depends on the external pull-up rail. A 300 ns response time provides predictable timing for control and interrupt paths, and the low 200 µA supply current per channel helps limit power use. Keep pull-up resistors close to the output or receiving logic, avoid excessive capacitive loading, and ensure the selected pull-up voltage remains within the comparator’s allowable output and supply conditions.

What is the LM2901DG4?
The LM2901DG4 is a Texas Instruments quad differential comparator with four independent channels, open-collector outputs, and a 14-pin SOIC package. According to the TI product page, the device is a 30 V comparator with an operating supply range of 2 V to 36 V. It supports single- or dual-supply operation and can compare four pairs of input voltages within one package.
What are the key specifications of LM2901DG4 that engineers should know?
The LM2901DG4 provides four differential comparator channels, 0.37 mV input offset voltage, 3.5 nA input bias current, and 200 µA supply current per comparator. Its 300 ns response time and open-collector outputs suit threshold-detection and control circuits. According to TI, the device operates from 2 V to 36 V, supports common-mode inputs down to ground, and provides a maximum supply rating of 38 V.
What is the operating voltage of LM2901DG4?
The LM2901DG4 operates from 2 V to 36 V and has a 38 V maximum supply-voltage rating. According to the TI LM2901 product page, it also supports single-supply and dual-supply configurations. The 30 V designation identifies the nominal supply rating used for the family, so actual circuit design should use the 36 V operating limit rather than treating 30 V as an absolute maximum.
Where can I download the LM2901DG4 datasheet PDF?
The LM2901DG4 datasheet is available through the Texas Instruments LM2901 product page, which links to ordering data, technical documents, and the family data sheet. The manufacturer page is the preferred source because it distinguishes LM2901 variants and package options. Use the LM2901 data sheet and the device-specific ordering information for the DG4 suffix when verifying pin functions and test conditions.
Where can I find the LM2901DG4 pinout?
The LM2901DG4 uses a 14-pin SOIC with four open-collector outputs and four differential input pairs. According to the LM2901 family pin configuration, outputs occupy pins 1, 7, 8, and 12; noninverting inputs occupy pins 3, 5, 10, and 14; inverting inputs occupy pins 2, 6, 9, and 13; ground is pin 4; and supply is pin 11. Verify the diagram against the manufacturer datasheet before routing the PCB.
How much noise does an open-collector LM2901DG4 output require?
The LM2901DG4 output requires an external pull-up resistor because the output stage can sink current but cannot actively source a high-level voltage. According to the LM2901 family information, the open-collector output is compatible with TTL, MOS, and CMOS logic. Select the pull-up value from the required logic-high voltage, sink-current limit, propagation-delay budget, and the power-supply rail used by the receiving circuit.
Can LM2901DG4 operate from a single 5 V supply?
Yes, the LM2901DG4 can operate from a single 5 V supply because its operating range begins at 2 V and extends to 36 V. According to the TI product page, the comparator supports both single and dual supplies. With a single supply, its common-mode input range including ground makes it suitable for detecting signals near 0 V, provided the input levels remain within the datasheet limits.
Is LM2901DG4 suitable for battery voltage monitoring?
The LM2901DG4 is suitable for battery monitoring because it supports supply voltages from 2 V to 36 V and consumes 200 µA per comparator. Its common-mode input range includes ground, allowing a resistor-divider threshold to be compared against a battery-derived signal. Account for the four channels' total supply demand and configure each open-collector output with the pull-up required by the display, indicator, or controller.
What can replace LM2901DG4?
The closest documented replacements include Texas Instruments LM2901DR, LM2901DRG4, LM2901DE4, and onsemi LM2901DG, each using a 14-pin SOIC format. The TI ordering variants share the LM2901 electrical family, while the onsemi device is a direct cross-manufacturer candidate for the same basic quad open-collector function. Confirm input polarity, output behavior, supply limits, and timing on the selected replacement's own datasheet.
Is onsemi LM2901DG the same as LM2901DG4?
The onsemi LM2901DG is a close functional alternative to the LM2901DG4, not an identical manufacturer order code. Both are described as quad differential comparators in 14-SOIC packages with open-collector outputs. According to the cross-reference information, the onsemi listing identifies CMOS and TTL-compatible output behavior, but engineers should verify offset, response time, common-mode range, and pin assignments before substitution.
LM2901DG4 vs LM2901DRG4 - which is better for an existing design?
The LM2901DG4 and LM2901DRG4 belong to the same Texas Instruments LM2901 family and use the same 14-pin SOIC footprint, making LM2901DRG4 a practical same-family replacement when its order code meets the production requirements. According to the cross-reference information, both provide four comparator functions. Verify the exact suffix details, marking, temperature grade, and qualification requirements before approving the substitution.
LM2901DG4 vs LM2901DE4 - what should be checked before replacement?
The LM2901DG4 and LM2901DE4 are Texas Instruments LM2901 variants listed with the same 14-pin SOIC package and four-comparator configuration, so the LM2901DE4 is a plausible footprint-compatible replacement. According to the available cross-reference information, both have the same stated 7 mV maximum offset and 1.3 µs response time. Confirm lead orientation, suffix meaning, temperature range, and current ordering status before redesigning the board.
When should I choose LM2901DG4 over an alternative?
Choose the LM2901DG4 when a design needs a 30 V nominal quad differential comparator, open-collector outputs, a 300 ns response time, and operation from a single 2 V to 36 V supply. According to TI, the device also provides a common-mode input range that includes ground. Select a documented alternative when supply, qualification, sourcing, or exact ordering requirements favor that part.
Is LM2901DG4 suitable for industrial sensor threshold detection?
The LM2901DG4 is suitable for industrial sensor threshold detection because it combines four independent differential channels with a 300 ns response time and an input common-mode range that includes ground. According to the TI product page, the open-collector outputs can drive TTL, MOS, and CMOS logic. Scale sensor signals into the input range, add hysteresis where needed, and use a suitable pull-up on each output.
Where can I buy LM2901DG4 and what is its price?
The LM2901DG4 can be requested through the Request a Quote form on this page, where current commercial terms, availability, and lead time should be confirmed for the exact suffix and package. No price figure is stated here because commercial terms change. The Texas Instruments product page and the component listings linked in the technical documentation can be used to confirm lifecycle, ordering, and package details.
What is the lead time and stock status for LM2901DG4?
Request the current stock position, lead time, and minimum order quantity through the Request a Quote form on this page. The Texas Instruments product page identifies the LM2901 family as an active product offering, but that status does not by itself guarantee inventory for every order code. State the exact LM2901DG4 suffix and required quantity when requesting a quotation.

Engineering reference data for LM2901DG4 — comparison, design guidance, and compliance information.

Selection Guide

Choose the LM2901DG4 for a four-channel threshold or protection design that needs a 300 ns response time, low 0.37 mV input offset, open-collector outputs, and operation from 2 V to 36 V. Its common-mode range including ground is useful for battery and low-level sensor monitoring. The Texas Instruments LM2901DR, LM2901DRG4, LM2901DE4, and LM2901DR2G are practical same-family options when their ordering, qualification, and timing details better fit the production program. Consider the onsemi LM2901DG for a cross-manufacturer sourcing option, but verify its offset, timing, input limits, and exact pin behavior against its datasheet. For any substitution, confirm the 14-pin SOIC footprint, supply limits, common-mode range, output sink capability, pull-up arrangement, and lifecycle requirements before releasing the PCB.

Comparison with Alternatives

Parameter This Product LM2901DR LM2901DRG4 LM2901DE4 LM2901DR2G LM2901DG
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments onsemi
Package 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC
Comparator Channels 4 4 4 4 4 4
Output Type Open collector Open collector Open collector Open collector Open collector Open collector
Logic Compatibility TTL, MOS, and CMOS TTL, MOS, and CMOS TTL, MOS, and CMOS TTL, MOS, and CMOS TTL, MOS, and CMOS CMOS and TTL

Key Differentiators

  • Faster stated response time (vs LM2901DR)
  • Lower input offset specification (vs LM2901DE4)
  • Quad-channel integration (vs LM2901DG)
  • Wide single- and dual-supply operation (vs LM2901DRG4)

Design Notes

Every LM2901DG4 output is open collector and requires an external pull-up resistor. Without a pull-up, the output cannot establish a valid logic-high level. Select the resistor using the receiving logic’s high-level voltage, permissible sink current, output capacitance, and desired rise time. Do not connect an output directly to a supply rail or exceed the output-stage voltage and current ratings.

Place input resistors or other conditioning networks close to the relevant LM2901DG4 input pins, and keep the two inputs of a channel as short as practical. Input nodes can be sensitive to nearby switching edges, so route them away from power inductors, relay wiring, and high-current outputs. Add small hysteresis or filtering where the compared signals cross slowly, because both noise and transition time can cause repeated output toggling.

Place the shared supply bypass capacitor close to pin 11 and provide a low-impedance ground return to pin 4. This is especially important when four open-collector outputs switch at once, causing simultaneous current transitions on the supply and ground system. Keep pull-up resistors near the outputs or receivers, use short ground paths, and separate sensitive comparator inputs from digital return currents to reduce threshold errors.

The LM2901DG4 can operate from 2 V to 36 V, but the complete circuit must remain within the input common-mode range, output-state limits, and absolute maximum ratings. Verify that the pull-up rail and any sensed voltage cannot exceed the applicable supply and differential-input constraints. Use resistor-divider ratios that keep both comparator inputs inside their operating range under every expected supply, tolerance, and transient condition.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

RoHS and REACH comparisons are mentioned for selected alternatives, but no explicit compliance declaration for LM2901DG4 was available. The general-purpose LM2901DG4 is not identified as an AEC-Q100-qualified automotive variant.

Related Searches

LM2901DG4 datasheet LM2901DG4 datasheet pdf LM2901DG4 pinout LM2901DG4 equivalent LM2901DG4 replacement LM2901DG4 cross reference LM2901DG4 vs LM2901DR LM2901DG4 vs LM2901DE4 Texas Instruments LM2901DG4 LM2901DG4 30V comparator LM2901DG4 14-SOIC LM2901DG4 price LM2901DG4 stock LM2901DG4 battery monitoring

Related Components & Terms

Texas Instruments LM2901DG4 LM2901 LM2901DR LM2901DRG4 LM2901DE4 LM2901DR2G onsemi LM2901DG differential comparator analog comparator quad comparator open-collector output linear integrated circuit semiconductor 14-pin SOIC SOIC family surface-mount package input offset voltage input bias current supply current common-mode input range response time single-supply operation dual-supply operation
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details