LM2901VD - 36V Quad Differential Comparator | onsemi
MPN: LM2901VD ✓ ActiveLM2901VD Overview
A differential comparator is an analog interface IC that converts the relationship between two input voltages into a digital output. In the broader semiconductor hierarchy, the LM2901VD belongs to the comparator family, which sits alongside amplifiers and other interface ICs. It is used where a system must establish whether a measured voltage is above or below a reference, such as in power-supply threshold detection, signal conditioning, and simple control systems.
Key features include single-supply or split-supply operation, a typical input bias current of 25 nA, and a typical input offset current of ±5.0 nA. The low input bias current reduces loading on high-impedance source circuits, which is useful when the comparator monitors a sensor or resistor-divider output. The wide 3 V to 36 V supply range supports industrial control systems, automotive equipment, consumer products, and embedded memory interfaces.
The open-collector output architecture requires an external pull-up resistor and permits the output to be pulled to a selected logic voltage. This feature enables connection to TTL-compatible systems and allows multiple comparator outputs to share a bus when suitable wired logic behavior is acceptable. The four independent channels can perform separate threshold, window, or sensing functions without sharing an internal signal path.
Typical applications include overvoltage and undervoltage detection, battery monitoring, industrial sensor interfaces, memory address decoding, automotive logic systems, and general-purpose control equipment. Because the output is open collector, designers should account for pull-up resistor selection, output rise time, bus capacitance, and the voltage and current ratings of the pull-up network.
The principal design consideration is common-mode and supply compatibility. Input and output conditions must remain within the limits stated in the manufacturer datasheet, and the external pull-up must not exceed the output transistor's voltage rating. The 14-pin SOIC footprint also requires adequate spacing between adjacent analog inputs to reduce noise coupling.
This page combines the manufacturer function description, package information, electrical highlights, verified sourcing links, drop-in comparison options, and practical circuit-design guidance to support faster component evaluation and PCB planning.
Drop-in alternatives for LM2901VD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM2901VD (same form factor and footprint) — differing in Comparator Type, Logic Compatibility, Number of Channels, Supply Voltage Range.
LM2901DG
✅ Drop-InContact for price
View Datasheet →NCV2901DR2G
✅ Drop-In📋 Reference alternative (not in catalog)
LM2901D
✅ Drop-InContact for price
View Datasheet →LM2901V-Q1
✅ Drop-In📋 Reference alternative (not in catalog)
LM2901QDRQ1
✅ Drop-In📋 Reference alternative (not in catalog)
LM2901VD Maximum Ratings & Electrical Characteristics
| Comparator Type | 4-channel differential comparator |
| Supply Voltage Range | 3 V to 36 V |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5.0 nA typical |
| Output Type | Open collector |
| Logic Compatibility | TTL compatible |
| Supply Configuration | Single or split supply |
| Number of Channels | 4 |
| Package | 14-pin SOIC |
| Mounting Type | Surface mount |
| Primary Application | Level detection, low-level sensing, and memory applications |
LM2901VD 14-pin soic Pin Configuration Guide
Pin configuration for LM2901VD (14-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LM2901VD.
Refer to the datasheet for full pin configuration.
Typical Applications
LM2901VD is suitable for 6 applications: Industrial Overvoltage Detection, Battery Low-Level Sensing, Memory Address Decoding, High-Impedance Sensor Interfacing, Automotive Logic and Fault Monitoring, Consumer Equipment Level Control.
Industrial Overvoltage Detection
The LM2901VD is appropriate for industrial threshold monitoring because it combines four differential channels with a 3 V to 36 V supply range. Each comparator can compare a divided supply-voltage signal against a reference and indicate when the monitored rail crosses a defined limit. Its typical 25 nA input bias current reduces the measurement error introduced by high-value divider resistors. The open-collector outputs can drive a system fault input through a pull-up resistor, allowing the board to distinguish normal and overvoltage states without adding a separate analog-to-digital converter. Industrial designs should verify common-mode limits, output timing, pull-up values, and isolation between adjacent channels during component qualification.
Recommended
Battery Low-Level Sensing
The LM2901VD can support battery low-level sensing in equipment operating from a wide supply range. Its four channels allow several battery thresholds, charger states, or divided cell voltages to be evaluated independently. The 25 nA typical input bias current is especially useful with resistive dividers because it minimizes loading of the sensed node. A comparator output can remain open during the detected state and be pulled high by an external resistor, allowing a low-power controller to recognize a fault without continuous conversion. The exact battery chemistry and operating voltages must remain within the comparator's common-mode and supply limits, and the pull-up network should be chosen to balance current consumption against switching speed.
Recommended
Memory Address Decoding
The LM2901VD is specifically suited to memory applications that require digital decisions from analog voltage relationships. Four independent comparator channels can evaluate multiple address, enable, or control lines and translate those conditions into open-collector logic states. The 14-pin SOIC keeps four channels in a compact surface-mount footprint, while the 3 V to 36 V supply capability permits operation from industrial and automotive-compatible rails. External pull-up resistors establish the inactive output level and may also support a wired-logic arrangement where appropriate. Because open-collector outputs rise through the pull-up network, propagation and rise time should be checked against the memory device's setup and hold requirements.
Recommended
High-Impedance Sensor Interfacing
The LM2901VD is useful when a sensor produces a slowly changing voltage that must be converted into a logic event. Its typical input bias current of 25 nA limits the current drawn from a high-impedance source, helping preserve the intended sensor signal. Four channels can monitor several thresholds or provide a window function by comparing the sensed voltage with upper and lower references. The open-collector output can trigger an interrupt, alarm, or control input when the crossing occurs. Designers should minimize PCB leakage around the input nodes, use suitable reference sources, and confirm that the sensor's voltage range remains within the common-mode operating region specified by the manufacturer.
Recommended
Automotive Logic and Fault Monitoring
The wide 3 V to 36 V operating range makes the LM2901VD family suitable for automotive-style electrical systems where a comparator must recognize voltage levels rather than measure them precisely. Four channels can support battery, actuator, sensor, and connectivity fault decisions. The typical 25 nA input bias current helps when monitoring high-impedance dividers, and open-collector outputs permit wired interface behavior when the system design supports it. For production automotive use, engineers should select a part with the required automotive qualification, validate transient and ESD requirements, and confirm that every input and output remains within the selected device's absolute-maximum ratings.
Recommended
Consumer Equipment Level Control
The LM2901VD can implement simple level decisions in consumer equipment, including power-good detection, battery status indication, input limiting, and mode switching. Four channels provide several threshold functions in one 14-pin SOIC without requiring a dedicated microcontroller ADC for every decision. The device accepts a 3 V to 36 V supply range, while its low typical input bias current reduces interference with divider-based sensing networks. Open-collector outputs are flexible for driving an enable, status LED, or logic input because the pull-up voltage can be selected independently. The design should account for the open-collector rise time, supply-current demand, common-mode limits, and the possibility that an adjacent switching node could couple noise into a high-impedance input.
Recommended
Recommended Products Summary
Engineering reference data for LM2901VD — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM2901DG | NCV2901DR2G | LM2901D | LM2901V-Q1 | LM2901QDRQ1 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 4 |
Key Differentiators
- Four independent channels in one 14-SOIC package (vs LM2901D)
- Low typical input bias current supports high-impedance sensing (vs LM2901V-Q1)
- Wide operating range supports industrial and vehicle electrical systems (vs LM2901QDRQ1)
Design Notes
The LM2901VD has open-collector outputs, so every output used as a logic signal needs an external pull-up resistor. Select the pull-up supply to suit the connected logic family and confirm that its voltage does not exceed the output-pin rating. The resistor also establishes the rise time, so avoid making it unnecessarily large when long traces or loaded buses require fast transitions. Account for pull-up current when the output is held low.
Place each pull-up resistor close to the corresponding output pin to limit trace capacitance and ringing. Route the four input pairs away from switching nodes, relay contacts, inductors, and other high-energy paths. Because input bias current is typically 25 nA, even modest board contamination can influence a high-impedance input. Use a suitable board finish, keep high-impedance nodes compact, and provide a nearby ground return to reduce coupling.
Use the 3 V to 36 V operating range as a boundary rather than assuming the full interval is suitable for every input. Check the common-mode input range at each actual supply condition, including split-supply operation. Confirm absolute-maximum ratings for input and output pins, especially when pull-ups connect to a voltage above or below the comparator supply. Review input protection paths when transients or reverse connection are possible.
The 14-pin SOIC footprint provides four differential comparator channels in one compact package, but adjacent channels should be assigned according to their signal sensitivity. Keep sensitive inverting and non-inverting traces short and matched where signal integrity matters. Decouple the comparator supply close to its power pin with a local ceramic capacitor and provide an adequate return path. Verify the manufacturer's land pattern and pin numbering against the selected ordering code before fabrication.
Compliance Information
The manufacturer datasheet and product listings should be consulted for the exact package's RoHS, REACH, lead-free, halogen-free, automotive, and conflict-minerals declarations.