LM2902M/NOPB - 26V Quad 1.2MHz Op Amp | Texas Instruments
MPN: LM2902M/NOPB ✓ ActiveLM2902M/NOPB Overview
An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2902 belongs to the hierarchy of four-channel general-purpose amplifiers within the broader operational-amplifier and analog IC categories. Its four independent channels make it useful where several low-frequency signals must be amplified, buffered, summed, or compared within one package.
The principal features include four independent amplifiers, a 26 V maximum total supply rating, approximately 1.2 MHz gain-bandwidth product, and approximately 2 mV input offset voltage. Its general-purpose performance is suitable for sensor conditioning, current-loop interfaces, audio and communication circuits, and industrial control signals. The 14-SOIC package provides a conventional surface-mount footprint and easy access to separate inputs, outputs, and supply connections for all four channels.
Internally, the LM2902M/NOPB uses a frequency-compensated four-amplifier architecture intended for stable operation with conventional external feedback networks. A gain-bandwidth product near 1.2 MHz gives adequate bandwidth for low-frequency instrumentation and control loops without making the device a high-speed precision amplifier. The stated 2 mV offset specification supports general signal conditioning, although applications requiring tighter calibration accuracy may need offset correction or a more precise amplifier.
Typical uses include buffering sensor outputs, amplifying low-level analog signals, driving slow comparators, implementing transimpedance stages, and providing gain in industrial instrumentation. Because each channel has independent input and output pins, multiple circuit blocks can be consolidated while preserving separate ground-referenced or feedback networks. The wide supply capability is particularly useful in 12 V or 24 V industrial environments, subject to the device's maximum operating limits.
Designers should verify common-mode input range, output swing, input bias current, slew rate, and thermal conditions against the manufacturer datasheet before fixing a supply voltage or gain. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left floating. Input-source impedance should also be considered because excessive imbalance can create offset and bias-current errors.
This page combines the manufacturer's principal operating characteristics, package and ordering details, practical application guidance, and a focused set of same-footprint replacement options. It also adds design notes and comparison criteria that help engineers determine whether the LM2902M/NOPB is suitable for a given signal-conditioning or industrial-control design.
Drop-in alternatives for LM2902M/NOPB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM2902M/NOPB (same form factor and footprint) — differing in Package, Operating Temperature Range, Amplifier Type, Input Offset Voltage, Maximum Supply Voltage.
LM2902M
✅ Drop-InContact for price
View Datasheet →LM2902KPWR
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →LM2902KDBR
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →LM2902NSR
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →LM2902M
✅ Drop-InContact for price
View Datasheet →LM2902M
✅ Drop-InContact for price
View Datasheet →LM2902M/NOPB Maximum Ratings & Electrical Characteristics
| Number of Amplifiers | 4 circuits |
| Amplifier Type | General purpose |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Package | 14-SOIC, 3.90 mm width |
| Operating Temperature Range | -40 °C to +85 °C |
| Slew Rate | 0.5 V/µs |
| Datasheet Gain-Bandwidth Product | 1 MHz |
| Packaging | Tube |
| Mounting Type | Surface mount |
| Number of Pins | 14 pins |
| Supply Configuration | Single or dual supply |
| Frequency Compensation | Internally compensated |
LM2902M/NOPB Pin Configuration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | -IN1 — Amplifier 1 inverting input |
| Pin 3 | +IN1 — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | +IN2 — Amplifier 2 non-inverting input |
| Pin 6 | -IN2 — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | -IN3 — Amplifier 3 inverting input |
| Pin 10 | +IN3 — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive supply connection |
| Pin 12 | +IN4 — Amplifier 4 non-inverting input |
| Pin 13 | -IN4 — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Typical Applications
LM2902M/NOPB is suitable for 6 applications: Industrial Sensor Signal Conditioning, Audio Preamplifier and Buffering, Transimpedance Amplifier, Current Loop Receiver, Power Supply Feedback and Monitoring, Portable and Battery-Powered Instrumentation.
Industrial Sensor Signal Conditioning
The LM2902M/NOPB fits industrial sensor interfaces that need several low-frequency amplification stages on one board. Its four independent channels can condition current or voltage sensor signals while sharing a 26 V maximum supply capability. The approximately 1.2 MHz gain-bandwidth product is suitable for general-purpose industrial signals rather than high-bandwidth waveform capture. A 12 V or 24 V industrial rail also provides useful headroom when designing noninverting or inverting amplifiers. Designers should confirm common-mode input range, output swing, and input bias current in the Texas Instruments LM2902 datasheet before setting the gain.
Recommended
Audio Preamplifier and Buffering
The LM2902M/NOPB can provide low-frequency gain and buffering for audio preamplifier stages that do not require rail-to-rail operation. Its four amplifier channels allow balanced input buffering, volume-control gain stages, or active filtering to be implemented in a compact 14-SOIC package. The 2 mV input offset figure is adequate for many general audio paths, while the approximately 1.2 MHz bandwidth supports modest-bandwidth tonal signals. Supply selection must preserve adequate output swing and common-mode range. Feedback-network values and decoupling placement should follow the manufacturer's application guidance.
Recommended
Transimpedance Amplifier
The LM2902M/NOPB is appropriate for modest-bandwidth photodiode or sensor-current-to-voltage conversion because it provides four internally compensated amplifier channels and approximately 1.2 MHz gain-bandwidth product. The feedback resistor and compensation capacitor determine practical sensitivity, bandwidth, and stability, so the circuit should be simulated with the actual photodiode capacitance and load. The 2 mV offset specification provides a baseline for many non-precision light-control loops. Input bias current, common-mode limits, and output swing must be checked against the operating point.
Recommended
Current Loop Receiver
The LM2902M/NOPB is well suited to receiving 4-20 mA industrial current-loop signals because four channels can support buffering, scaling, filtering, and comparison within one package. Its 26 V maximum supply accommodates industrial environments better than a low-voltage precision amplifier, while the approximately 1.2 MHz bandwidth is more than adequate for typical process-control loops. Use an input resistor to convert the loop current into a voltage and confirm that the resulting voltage remains within the amplifier's common-mode range. Include input protection when the field wiring is exposed to transients.
Recommended
Power Supply Feedback and Monitoring
The LM2902M/NOPB can monitor and buffer multiple power-related voltages in industrial or communications equipment. Its four channels may compare a scaled rail against a reference, provide buffered fault signals, or amplify differential sensing lines. The wide 26 V maximum supply is useful around 12 V and 24 V rails, although the amplifier itself is not a dedicated voltage-reference or protection device. Check that the sensed voltage remains inside the input common-mode range and that the output does not exceed the selected load capability. Place supply-bypass capacitors close to pins 4 and 11.
Recommended
Portable and Battery-Powered Instrumentation
The LM2902M/NOPB can consolidate low-speed analog channels in battery-powered instrumentation where four separate amplifiers would otherwise increase board area. Its low-power general-purpose architecture is useful for sensor interfaces, threshold amplifiers, and modest-gain stages, although quiescent current should be compared with the system's energy budget. The broad supply range permits operation from several common rail arrangements, subject to the exact input and output limits. Power-gating, shutdown behavior, and the input bias current of the selected amplifier are important checks for portable equipment.
Recommended
Recommended Products Summary
Engineering reference data for LM2902M/NOPB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM2902M | LM2902KPWR | LM2902KDBR | LM2902NSR | LM2902M | LM2902M |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | Panasonic |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Amplifier Type | General purpose | General purpose | General purpose | General purpose | General purpose | General purpose | General purpose |
Key Differentiators
- Four independent amplifiers in one conventional 14-SOIC package (vs LM2902KPWR)
- Higher stated gain-bandwidth product (vs onsemi LM2902M)
- Direct TI LM2902 family sourcing path (vs Panasonic LM2902M)
Design Notes
Place the supply-bypass capacitor as close as practical to pins 4 and 11, and route the supply and ground returns without narrow breaks between layers. Because this is a four-amplifier device, total supply current rises with the number of active channels. Use the datasheet's quiescent-current and output-current limits to size the supply, and avoid treating the maximum 26 V rating as a recommended operating point.
Do not assume rail-to-rail input or output behavior. Verify the common-mode input range and output swing at the selected supply voltage, particularly in single-supply sensor circuits where the signal sits near ground. The 2 mV offset rating is suitable for general-purpose conditioning, but precision measurements may require offset trimming or a more accurate amplifier.
Route each amplifier's input and feedback paths compactly and keep high-impedance input nodes away from output and supply traces. The 14-SOIC footprint has sufficient pin spacing for conventional routing, but adjacent channels can share ground infrastructure. Confirm exposed-pad thermal and copper recommendations in the manufacturer package drawing before finalizing the land pattern.
Choose feedback resistors and compensation capacitors to maintain stable closed-loop behavior with the actual source impedance and load capacitance. Input bias-current error becomes more visible with high source resistance and a 2 mV offset specification is only a general-purpose baseline. For photodiode, capacitive sensor, or long-cable interfaces, simulate the complete source network rather than relying only on nominal gain-bandwidth product.
Compliance Information
Compliance claims require confirmation for the exact /NOPB ordering code. The /NOPB suffix identifies lead-free ordering, but no explicit RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statement was confirmed.