LM2903YPT - Dual 36V Low-Power Comparator | STMicroelectronics
MPN: LM2903YPT ✓ ActiveLM2903YPT Overview
A voltage comparator is an analog interface IC that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its two channels can operate independently, making it suitable for threshold detection, window sensing, level translation, and basic control loops that require only polarity rather than an analog amplified output.
The LM2903YPT features a very low supply current of 0.4 mA, described as independent of supply voltage. Operation at a 5 V supply corresponds to approximately 1 mW per comparator. Its low 25 nA typical input bias current and ±5 nA typical input offset current reduce errors when the sensing source has high source impedance. The open-collector outputs also permit wired connection to a common pull-up when an application requires a shared bus.
The LM2903 architecture supports wide supply flexibility while retaining low power consumption. Each comparator has differential inputs and an independently controlled open-collector output. Because the output transistor can remain off, the effective output state depends on the external pull-up resistor, supply voltage, and leakage current. This architecture provides compatibility with digital logic but requires suitable pull-up placement and accounting for bus rise time.
Typical uses include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, window comparators, and control systems operating across widely varying supply voltages. Two channels can be combined to form a window detector, with one comparator monitoring the upper threshold and the other monitoring the lower threshold. In automotive, industrial, or instrumentation systems, the low supply current helps limit standby power while the broad supply range simplifies power architecture.
A key design consideration is output pull-up selection. The resistor must pull the open-collector node high without exceeding the output current limit, while keeping rise time acceptable for the receiving logic. Input common-mode limits, output timing, and absolute maximum ratings should be checked against the manufacturer datasheet for the exact operating conditions. The unused comparator channel should be configured according to the recommended application guidance rather than left floating.
This product page combines the exact LM2903YPT ordering information with technical specifications, package and pin guidance, sourcing instructions, and practical comparison notes. It also highlights the restrictions that matter when evaluating a replacement: voltage range, output architecture, channel count, package footprint, temperature grade, and timing must all be compatible.
Drop-in alternatives for LM2903YPT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM2903YPT (same form factor and footprint) — differing in Package, Output Type, Comparator Type, Input Bias Current, Automotive Qualification.
LM2903WYPT
✅ Drop-InContact for price
View Datasheet →LM2903MPT
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
LM2903ST
✅ Drop-InContact for price
View Datasheet →LM2903YPT Maximum Ratings & Electrical Characteristics
| Comparator Type | Low-power dual voltage comparator |
| Number of Channels | 2 channels |
| Channel Independence | 2 independent comparators |
| Single-Supply Voltage Range | +2 V to +36 V |
| Dual-Supply Voltage Range | ±1 V to ±18 V |
| Supply Current | 0.4 mA, independent of supply voltage |
| Power Consumption per Comparator | 1 mW at +5 V |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5 nA typical |
| Propagation Delay | 1.3 µs |
| Output Type | Open-collector |
| Common-Mode Range | Rail-to-rail |
| Logic Compatibility | TTL, DTL, ECL, CMOS, and MOS |
| Package | 8-pin TSSOP |
| Mounting Type | Surface mount |
LM2903YPT Pin Configuration
| Pin 1 | OUT1 — Comparator 1 open-collector output |
| Pin 2 | IN1- — Comparator 1 inverting input |
| Pin 3 | IN1+ — Comparator 1 non-inverting input |
| Pin 4 | GND — Ground connection |
| Pin 5 | IN2+ — Comparator 2 non-inverting input |
| Pin 6 | IN2- — Comparator 2 inverting input |
| Pin 7 | OUT2 — Comparator 2 open-collector output |
| Pin 8 | VCC — Positive supply connection |
Typical Applications
LM2903YPT is suitable for 6 applications: Battery-Powered Sensor Monitoring, Industrial Overvoltage Detection, Window Voltage Comparator, Battery Charge State Detection, Process Control Threshold Interface, Logic-Level Interface.
Battery-Powered Sensor Monitoring
The LM2903YPT fits battery-powered monitoring because its two independent channels operate from a single 2 V to 36 V supply while drawing 0.4 mA. A sensor signal can be compared against a reference on one channel, while the second channel monitors a different threshold or provides fault detection. The 25 nA typical input bias current is especially useful with high-impedance sensing sources, where bias current can create an error voltage. The open-collector output can drive a pull-up for low-power logic, although the resistor value must balance logic rise time against continuous current consumption.
Recommended
Industrial Overvoltage Detection
The LM2903YPT is suitable for industrial overvoltage supervision because it accepts a broad single-supply range of +2 V to +36 V and offers two independent comparison channels. One input can receive a divided representation of the monitored rail while the other receives a precision threshold. Its 1.3 µs propagation delay supports relatively prompt fault signaling without introducing the complexity of a more elaborate programmable monitor. Because the output is open collector, an external pull-up allows direct interface with a system supervisor, relay-control input, or isolated alarm stage while keeping the output polarity defined by the external network.
Recommended
Window Voltage Comparator
Both LM2903YPT channels can be combined to form an upper- and lower-threshold window detector. The first comparator identifies when the monitored voltage rises above the high limit, while the second identifies when it falls below the low limit. Their independent inputs permit the thresholds to be generated separately with resistor networks or references. The device's low 0.4 mA supply current helps limit power in continuously monitored systems, and the open-collector outputs permit the two states to be combined with wired logic. Designers must select pull-up values that preserve valid rise times and verify both channels against the required response delay.
Recommended
Battery Charge State Detection
The LM2903YPT can compare two battery-related voltages to identify charge, discharge, or fault conditions. Its single-supply operation from +2 V to +36 V accommodates low-cell packs and higher protected rails, while the low input bias current minimizes loading of the sensed source. Two channels can monitor separate pack voltages or compare a measured level against two thresholds. The open-collector output is useful for driving a pull-up into a microcontroller input, though the receiving device must accept the resulting voltage and the pull-up current must remain within the comparator output rating. Thermal and common-mode limits should be checked at the highest expected pack voltage.
Recommended
Process Control Threshold Interface
The LM2903YPT can serve as the threshold interface between a process sensor and a control system in industrial equipment. Its differential inputs allow the comparator to evaluate a sensor-derived voltage against a reference, while 1.3 µs propagation delay provides a defined response interval for switching or alarm logic. Two channels can support independent upper and lower limits or perform redundant comparisons. The low 25 nA typical input bias current reduces disturbance to high-impedance sensor outputs, and the wide supply range simplifies operation across mixed-voltage systems. Pull-up resistors should be placed close to the open-collector pins to limit parasitic capacitance and obtain predictable logic rise times.
Recommended
Logic-Level Interface
The LM2903YPT can translate a low-voltage or polarity-based analog decision into an open-collector logic signal. The pull-up resistor establishes the high output voltage independently of the comparator's open-collector transistor, allowing the output to interface with suitable TTL, DTL, ECL, CMOS, or MOS logic levels. Its 0.4 mA supply current helps preserve system power budget, and the two channels can implement independent decision outputs. The external pull-up must be checked for output current, voltage, noise margin, and rise-time requirements. For high fan-out or a fixed push-pull output requirement, a comparator with buffered push-pull outputs may provide a simpler implementation.
Recommended
Recommended Products Summary
Engineering reference data for LM2903YPT — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM2903WYPT | LM2903MPT | LM2903ST |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Diodes Incorporated |
| Package | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP |
| Comparator Channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector |
Key Differentiators
- Wide supply range with two independent channels (vs LM2903ST)
- Low supply current independent of supply voltage (vs LM2903WYPT)
- Low input bias current supports high-impedance sensing (vs LM2903ST)
Design Notes
Place each open-collector pull-up resistor close to the corresponding OUT pin to minimize parasitic capacitance on the logic node. The resistor must pull the output above the receiving device's input threshold while keeping the maximum pull-up current below the comparator output-current limit. With a 5 V logic rail, check both the low-level sink current and the resulting rise time before finalizing the value.
Do not assume that the base family name is enough for substitution. Confirm the exact suffix, 8-pin TSSOP dimensions, pin mapping, temperature grade, qualification status, and packing method. A drop-in footprint preserves PCB compatibility, but the replacement must still satisfy the original circuit's common-mode input range, output-current requirement, propagation delay, and supply-voltage limits.
Keep comparator input routing away from switching nodes and the open-collector output return path because coupling can shift the crossing point. If the sensing source has high impedance, use short traces, a nearby reference connection, and an appropriate source impedance. The specified 25 nA typical input bias current is low, but comparator input capacitance, leakage, and external resistor errors can still influence the effective threshold.
Estimated: with a +5 V supply and 0.4 mA supply current, the device-level supply consumption is approximately 2.0 mW for both channels. This estimate uses the manufacturer supply-current figure and excludes external pull-up current. Add the pull-up and input-network consumption when calculating total system standby power, particularly for continuously monitored battery systems.
Compliance Information
The LM2903 manufacturer datasheet discusses AEC Q100 qualification language, but the exact LM2903YPT ordering-grade status and suffix-specific environmental declarations require confirmation before being assigned to this exact MPN.