STMicroelectronics

LM2903YPT - Dual 36V Low-Power Comparator | STMicroelectronics

부품 번호: LM2903YPT ✓ 활성
+2 V to +36 V Vdss 0.4 mA, independent of supply voltage Id 8-pin TSSOP Package
MOQ: 1 |

LM2903YPT 개요

The STMicroelectronics LM2903YPT is a dual low-power voltage comparator with two independent channels, an open-collector output stage, and operation from a single 2 V to 36 V supply or split supplies of ±1 V to ±18 V. The device is packaged in an 8-pin TSSOP and is identified as rail-to-rail by its distributor listing.

A voltage comparator is an analog interface IC that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its two channels can operate independently, making it suitable for threshold detection, window sensing, level translation, and basic control loops that require only polarity rather than an analog amplified output.

The LM2903YPT features a very low supply current of 0.4 mA, described as independent of supply voltage. Operation at a 5 V supply corresponds to approximately 1 mW per comparator. Its low 25 nA typical input bias current and ±5 nA typical input offset current reduce errors when the sensing source has high source impedance. The open-collector outputs also permit wired connection to a common pull-up when an application requires a shared bus.

The LM2903 architecture supports wide supply flexibility while retaining low power consumption. Each comparator has differential inputs and an independently controlled open-collector output. Because the output transistor can remain off, the effective output state depends on the external pull-up resistor, supply voltage, and leakage current. This architecture provides compatibility with digital logic but requires suitable pull-up placement and accounting for bus rise time.

Typical uses include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, window comparators, and control systems operating across widely varying supply voltages. Two channels can be combined to form a window detector, with one comparator monitoring the upper threshold and the other monitoring the lower threshold. In automotive, industrial, or instrumentation systems, the low supply current helps limit standby power while the broad supply range simplifies power architecture.

A key design consideration is output pull-up selection. The resistor must pull the open-collector node high without exceeding the output current limit, while keeping rise time acceptable for the receiving logic. Input common-mode limits, output timing, and absolute maximum ratings should be checked against the manufacturer datasheet for the exact operating conditions. The unused comparator channel should be configured according to the recommended application guidance rather than left floating.

This product page combines the exact LM2903YPT ordering information with technical specifications, package and pin guidance, sourcing instructions, and practical comparison notes. It also highlights the restrictions that matter when evaluating a replacement: voltage range, output architecture, channel count, package footprint, temperature grade, and timing must all be compatible.

드롭인 대체품: LM2903YPT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: LM2903YPT (동일 폼 팩터 및 풋프린트) — 차이점: Package, Output Type, Comparator Type, Input Bias Current, Automotive Qualification.

Texas Instruments
Package: 8-TSSOP, 4.40 mm width
Output Type: Open collector
Comparator Type: Dual differential comparator
비교 대상: LM2903YPT →
STMicroelectronics
Package: 8-pin MiniSO (ST suffix)
Output Type: Open collector
Comparator Type: General purpose, open-collector output
비교 대상: LM2903YPT →
STMicroelectronics
Package: TSSOP-8
Output Type: Open-Collector, Rail-to-Rail
Input Bias Current: 250 nA
비교 대상: LM2903YPT →

LM2903WYPT

✅ 드롭인
STMicroelectronics
📦 8-pin TSSOP
2 (dual) · 2 V to 36 V · 1 V to 18 V · 250 nA · Open-Collector, Rail-to-Rail · Includes ground · -40C to +125C · TSSOP-8

가격 문의

데이터시트 보기 →

LM2903MPT

✅ 드롭인 ⚠️ 사양 미검증
📦 8-pin TSSOP
Same manufacturer and LM2903 family with equivalent dual open-collector architecture; suffix-specific temperature and qualification ratings may differ by 0%.

📋 참조 대체품 (카탈로그에 없음)

LM2903ST

✅ 드롭인
STMicroelectronics
📦 8-pin TSSOP
2 · General purpose, open-collector output · +2 V to +36 V · ±1 V to ±18 V · 0.4 mA (typical, independent of supply voltage) · 1 mW at +5 V · 25 nA (typical) · ±5 nA (typical)

가격 문의

데이터시트 보기 →

LM2903YPT 최대 정격 & 전기적 특성

Comparator Type Low-power dual voltage comparator
Number of Channels 2 channels
Channel Independence 2 independent comparators
Single-Supply Voltage Range +2 V to +36 V
Dual-Supply Voltage Range ±1 V to ±18 V
공급 전류 0.4 mA, independent of supply voltage
Power Consumption per Comparator 1 mW at +5 V
Input Bias Current 25 nA typical
Input Offset Current ±5 nA typical
Propagation Delay 1.3 µs
출력 유형 Open-collector
Common-Mode Range Rail-to-rail
Logic Compatibility TTL, DTL, ECL, CMOS, and MOS
패키지 8-pin TSSOP
실장 유형 Surface mount

LM2903YPT 핀 구성

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
핀 1 OUT1 — Comparator 1 open-collector output
핀 2 IN1- — Comparator 1 inverting input
핀 3 IN1+ — Comparator 1 non-inverting input
핀 4 GND — Ground connection
핀 5 IN2+ — Comparator 2 non-inverting input
핀 6 IN2- — Comparator 2 inverting input
핀 7 OUT2 — Comparator 2 open-collector output
핀 8 VCC — Positive supply connection

일반적인 애플리케이션

LM2903YPT 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Monitoring, Industrial Overvoltage Detection, Window Voltage Comparator, Battery Charge State Detection, Process Control Threshold Interface, Logic-Level Interface.

🔋

Battery-Powered Sensor Monitoring

The LM2903YPT fits battery-powered monitoring because its two independent channels operate from a single 2 V to 36 V supply while drawing 0.4 mA. A sensor signal can be compared against a reference on one channel, while the second channel monitors a different threshold or provides fault detection. The 25 nA typical input bias current is especially useful with high-impedance sensing sources, where bias current can create an error voltage. The open-collector output can drive a pull-up for low-power logic, although the resistor value must balance logic rise time against continuous current consumption.

🏭

Industrial Overvoltage Detection

The LM2903YPT is suitable for industrial overvoltage supervision because it accepts a broad single-supply range of +2 V to +36 V and offers two independent comparison channels. One input can receive a divided representation of the monitored rail while the other receives a precision threshold. Its 1.3 µs propagation delay supports relatively prompt fault signaling without introducing the complexity of a more elaborate programmable monitor. Because the output is open collector, an external pull-up allows direct interface with a system supervisor, relay-control input, or isolated alarm stage while keeping the output polarity defined by the external network.

📊

Window Voltage Comparator

Both LM2903YPT channels can be combined to form an upper- and lower-threshold window detector. The first comparator identifies when the monitored voltage rises above the high limit, while the second identifies when it falls below the low limit. Their independent inputs permit the thresholds to be generated separately with resistor networks or references. The device's low 0.4 mA supply current helps limit power in continuously monitored systems, and the open-collector outputs permit the two states to be combined with wired logic. Designers must select pull-up values that preserve valid rise times and verify both channels against the required response delay.

⚡

Battery Charge State Detection

The LM2903YPT can compare two battery-related voltages to identify charge, discharge, or fault conditions. Its single-supply operation from +2 V to +36 V accommodates low-cell packs and higher protected rails, while the low input bias current minimizes loading of the sensed source. Two channels can monitor separate pack voltages or compare a measured level against two thresholds. The open-collector output is useful for driving a pull-up into a microcontroller input, though the receiving device must accept the resulting voltage and the pull-up current must remain within the comparator output rating. Thermal and common-mode limits should be checked at the highest expected pack voltage.

🔧

Process Control Threshold Interface

The LM2903YPT can serve as the threshold interface between a process sensor and a control system in industrial equipment. Its differential inputs allow the comparator to evaluate a sensor-derived voltage against a reference, while 1.3 µs propagation delay provides a defined response interval for switching or alarm logic. Two channels can support independent upper and lower limits or perform redundant comparisons. The low 25 nA typical input bias current reduces disturbance to high-impedance sensor outputs, and the wide supply range simplifies operation across mixed-voltage systems. Pull-up resistors should be placed close to the open-collector pins to limit parasitic capacitance and obtain predictable logic rise times.

🌐

Logic-Level Interface

The LM2903YPT can translate a low-voltage or polarity-based analog decision into an open-collector logic signal. The pull-up resistor establishes the high output voltage independently of the comparator's open-collector transistor, allowing the output to interface with suitable TTL, DTL, ECL, CMOS, or MOS logic levels. Its 0.4 mA supply current helps preserve system power budget, and the two channels can implement independent decision outputs. The external pull-up must be checked for output current, voltage, noise margin, and rise-time requirements. For high fan-out or a fixed push-pull output requirement, a comparator with buffered push-pull outputs may provide a simpler implementation.

추천 제품 요약

LM2903 Base dual comparator family 사용처: Battery-Powered Sensor Monitoring, Industrial Overvoltage Detection, Window Voltage Comparator, Battery Charge State Detection, Process Control Threshold Interface, Logic-Level Interface LM2903WYPT STMicroelectronics 사용처: Battery-Powered Sensor Monitoring, Window Voltage Comparator, Process Control Threshold Interface LM2903B LM2903-family drop-in comparator option 사용처: Industrial Overvoltage Detection, Battery Charge State Detection, Logic-Level Interface
What is the operating voltage range of LM2903YPT?
The LM2903YPT operates from a single supply of +2 V to +36 V or from split supplies of ±1 V to ±18 V. According to the STMicroelectronics LM2903 datasheet, the device contains two independent low-power voltage comparators, and its wide supply range supports both low-voltage logic systems and higher industrial rails. Actual input and output conditions must remain within the applicable common-mode and absolute-maximum limits.
Where can I download the LM2903YPT datasheet PDF?
The official LM2903YPT datasheet PDF is available from the STMicroelectronics product documentation linked on this page. The manufacturer identifies the device as two independent low-power voltage comparators and specifies operation from +2 V to +36 V or ±1 V to ±18 V. Use the manufacturer PDF for the authoritative pin description, electrical limits, test conditions, and ordering information.
What is the LM2903YPT pinout?
The LM2903YPT uses an 8-pin TSSOP arrangement with one output, two differential inputs, ground, and supply for each independent comparator. According to the LM2903 manufacturer datasheet, pins 1 and 7 are the two open-collector outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are non-inverting inputs, pin 4 is ground, and pin 8 is the supply connection. Use the package drawing when assigning PCB tracks.
How much supply current does the LM2903YPT consume?
The LM2903YPT draws 0.4 mA of supply current, specified as independent of supply voltage. The STMicroelectronics datasheet also identifies approximately 1 mW of consumption per comparator when operating from +5 V. This low-power behavior makes the device suitable for battery-powered sensing, monitoring, and control circuits where continuous standby current is an important design constraint.
What are the key specifications of LM2903YPT that engineers should know?
The LM2903YPT is a dual, low-power, open-collector comparator designed for +2 V to +36 V single-supply operation or ±1 V to ±18 V split-supply operation. According to the manufacturer datasheet, it has 0.4 mA supply current, 25 nA typical input bias current, ±5 nA typical input offset current, and 1.3 µs propagation delay. It is supplied in an 8-pin TSSOP package.
Can LM2903YPT be used with a single 5 V supply?
Yes, the LM2903YPT supports a single +5 V supply because its specified single-supply range extends from +2 V to +36 V. The manufacturer datasheet identifies approximately 1 mW consumption per comparator at +5 V. Each open-collector output still requires an external pull-up resistor to establish a valid high level, and the pull-up should be selected according to the required logic speed and output-current limits.
What is the difference between LM2903YPT and LM2903WYPT?
Both are STMicroelectronics LM2903-family dual open-collector comparators associated with the 8-pin TSSOP footprint, but their ordering suffixes indicate different device variants. The LM2903YPT is the primary target specified here, while LM2903WYPT appears in the manufacturer-family cross-reference results. Check the exact suffix, temperature range, grade, and marking requirements in the manufacturer ordering table before treating one as a substitution.
LM2903YPT vs LM2903B - which is better for a legacy design?
The LM2903B is described by Texas Instruments as a drop-in replacement for LM2903, LM293, and LM393 variants, while the LM2903YPT is an STMicroelectronics 8-pin TSSOP ordering option. Selection should be based on the exact package, pin arrangement, supply range, output type, and timing requirements of the original design. Package dimensions and suffix-specific qualification must also be checked before PCB reuse.
When should I choose LM2903YPT instead of a generic dual comparator?
Choose the LM2903YPT when the design needs two independent low-power comparators, an open-collector output, and operation across a broad +2 V to +36 V supply range. Its 0.4 mA supply current and 25 nA typical input bias current are useful in battery-operated sensing and industrial monitoring systems. A comparator with push-pull outputs or lower input offset voltage may be preferable when rise time, fanout, or precision dominates the design.
What is the best drop-in replacement for LM2903YPT?
The closest documented options are the STMicroelectronics LM2903WYPT and the Diodes Incorporated LM2903ST, because each is associated with an 8-pin TSSOP comparator configuration and the same open-collector dual-channel architecture. No replacement should be treated as drop-in until package dimensions, pin mapping, supply limits, common-mode range, propagation delay, temperature grade, and output-current ratings are checked against the manufacturer datasheets.
Is LM2903YST the same as LM2903YPT?
No, LM2903YST and LM2903YPT are distinct ordering codes whose suffix details must be checked individually. The verified target is LM2903YPT from STMicroelectronics, and the comparison should not rely on the base LM2903 family name alone. Confirm the package, temperature range, qualification grade, tape-and-reel packing, and any lead-free processing requirements on the manufacturer ordering information before substitution.
What can replace LM2903YPT in an 8-pin TSSOP design?
The LM2903WYPT from STMicroelectronics and LM2903ST from Diodes Incorporated are the closest candidates identified for the 8-pin TSSOP footprint. Both must be verified for exact pin-to-pin compatibility and equivalent electrical limits because the open-collector pull-up network, input common-mode range, and propagation delay affect circuit behavior. Also confirm that the replacement can be sourced in the required package and production quantity.
Is LM2903YPT suitable for battery-powered sensor monitoring?
The LM2903YPT is suitable for many battery-powered sensor-monitoring circuits because it combines two independent channels with a 0.4 mA supply current. The low 25 nA typical input bias current also helps when driving high-impedance sensing elements. Power consumption still depends on the complete circuit, including pull-up resistors, input bias, and the duration for which the output remains active.
Where can I buy LM2903YPT and check current availability?
Use the Request a Quote form on this page to request the current LM2903YPT price, stock position, minimum order quantity, and lead time. The product is an 8-pin TSSOP dual comparator from STMicroelectronics, and the order code includes its customer-specific packing suffix. The request should state the required quantity, delivery destination, and whether reel, cut-tape, or another approved packing format is needed.
How much does LM2903YPT cost and what is its lead time?
The current commercial terms for LM2903YPT are obtained through the Request a Quote form on this page. Submit the required quantity, delivery location, target date, and packaging preference so XAIPART can confirm current availability, lead time, and a quotation for the exact ordering code. Because the YPT suffix identifies a specific customer packing configuration, the complete MPN should be used in the request.
Is LM2903YPT in stock?
Stock status for the exact LM2903YPT ordering code should be confirmed through the Request a Quote form on this page. Provide the required quantity, shipment country, target date, and packaging preference. The form allows XAIPART to check the current supply position without presenting a static stock count that may change during manufacturing and distribution.

엔지니어링 참조 데이터: LM2903YPT — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the LM2903YPT for low-power threshold detection using two independent comparators, particularly when the circuit operates from a single supply between +2 V and +36 V and needs an open-collector output. Select the LM2903WYPT when its suffix-specific temperature or qualification characteristics better match the production application. The LM2903MPT is another same-family TSSOP option, but its exact ordering ratings must be confirmed. The Diodes Incorporated LM2903ST may suit cost-focused designs after its common-mode range, output-current limit, timing, and temperature grade are verified against the original design. None of these choices is automatically interchangeable based on package appearance alone; preserve the pin functions, pull-up network, supply limits, input range, and switching requirements during qualification.

대체품과의 비교

파라미터 이 제품 LM2903WYPT LM2903MPT LM2903ST
Brand STMicroelectronics STMicroelectronics STMicroelectronics Diodes Incorporated
Package 8-pin TSSOP 8-pin TSSOP 8-pin TSSOP 8-pin TSSOP
Comparator Channels 2 independent channels 2 independent channels 2 independent channels 2 channels
Output Type Open-collector Open-collector Open-collector Open-collector

주요 차별점

  • Wide supply range with two independent channels (vs LM2903ST)
  • Low supply current independent of supply voltage (vs LM2903WYPT)
  • Low input bias current supports high-impedance sensing (vs LM2903ST)

설계 노트

Place each open-collector pull-up resistor close to the corresponding OUT pin to minimize parasitic capacitance on the logic node. The resistor must pull the output above the receiving device's input threshold while keeping the maximum pull-up current below the comparator output-current limit. With a 5 V logic rail, check both the low-level sink current and the resulting rise time before finalizing the value.

Do not assume that the base family name is enough for substitution. Confirm the exact suffix, 8-pin TSSOP dimensions, pin mapping, temperature grade, qualification status, and packing method. A drop-in footprint preserves PCB compatibility, but the replacement must still satisfy the original circuit's common-mode input range, output-current requirement, propagation delay, and supply-voltage limits.

Keep comparator input routing away from switching nodes and the open-collector output return path because coupling can shift the crossing point. If the sensing source has high impedance, use short traces, a nearby reference connection, and an appropriate source impedance. The specified 25 nA typical input bias current is low, but comparator input capacitance, leakage, and external resistor errors can still influence the effective threshold.

Estimated: with a +5 V supply and 0.4 mA supply current, the device-level supply consumption is approximately 2.0 mW for both channels. This estimate uses the manufacturer supply-current figure and excludes external pull-up current. Add the pull-up and input-network consumption when calculating total system standby power, particularly for continuously monitored battery systems.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The LM2903 manufacturer datasheet discusses AEC Q100 qualification language, but the exact LM2903YPT ordering-grade status and suffix-specific environmental declarations require confirmation before being assigned to this exact MPN.

데이터 검증일: 2026-11-17 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

lm2903ypt datasheet LM2903YPT pinout LM2903YPT datasheet pdf LM2903YPT TSSOP footprint LM2903YPT equivalent LM2903YPT replacement LM2903YPT vs LM2903WYPT LM2903YPT open collector output LM2903YPT supply current LM2903YPT price LM2903YPT stock STMicroelectronics LM2903YPT

관련 부품 & 용어

STMicroelectronics LM2903YPT LM2903WYPT LM2903MPT LM2903ST LM2903 LM2903B Diodes Incorporated Texas Instruments dual voltage comparator comparator analog interface IC open-collector output low-power comparator single-supply operation split-supply operation TSSOP-8 TSSOP package family surface-mount package input bias current input offset current propagation delay supply current industrial threshold detection battery-powered monitoring
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기