LM2904DGKR - Dual 26V 700kHz Op Amp | Texas Instruments
MPN: LM2904DGKR ✓ ActiveLM2904DGKR Overview
An operational amplifier is a voltage-amplifying component that uses high open-loop gain and negative feedback to create accurate, stable analog signal paths. The dual-amplifier configuration reduces component count where two independent channels are required. Within the broader hierarchy of an operational amplifier, amplifier IC, analog IC, and semiconductor, the LM2904 occupies the general-purpose segment rather than a precision or high-speed specialty category.
The LM2904 family provides low input offset voltage, a common-mode input range that extends to ground, and high differential input-voltage capability. The TI product page identifies the LM2904 as a dual, 26 V, 700 kHz operational amplifier, while the LM2904B family adds upgraded functionality and 36 V high-voltage operation. The LM2904DGKR ordering code specifically identifies the 8-pin VSSOP configuration, supporting compact surface-mount construction.
Each channel is frequency compensated for closed-loop gain of 10 or more. The internal compensation enables straightforward implementation of non-inverting and inverting amplifiers, voltage followers, comparators, summing circuits, and basic active filters. Because the two amplifiers are independent, they can process different analog signals, although common power and ground pins share the total package current and thermal limitations.
Typical uses include industrial sensor interfaces, low-frequency control loops, transducers, audio preamplification, battery-powered monitoring, test equipment, and general-purpose power-supply feedback. The VSSOP footprint is useful when a conventional 8-pin SOIC would occupy excessive board area. Designers should still evaluate input common-mode range, output swing, supply voltage, stability, and noise at the intended operating point.
For reliable layout, place the bypass capacitor at the supply pins and maintain a short return path to the ground pins. Avoid long input traces that can acquire noise, especially when the LM2904 is used with high-impedance sources. Check output-current limits when driving a load, and verify that the selected gain, feedback values, and capacitive loading remain compatible with the device’s frequency-compensated architecture.
This page combines manufacturer specifications, package and sourcing information, compatible replacement options, comparison parameters, and practical layout guidance to support component selection and PCB implementation for the LM2904DGKR.
Drop-in alternatives for LM2904DGKR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM2904DGKR (same form factor and footprint) — differing in Gain-Bandwidth Product, Amplifier Type, Common-Mode Input Range, Maximum Supply Voltage, Operating Temperature Range.
LM2904BDGKR
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
LM2904DGD
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
LM2904DGKR
✅ Drop-InContact for price
View Datasheet →LM2904DG
✅ Drop-InContact for price
View Datasheet →LM2904DG
✅ Drop-InContact for price
View Datasheet →LM2904DG
✅ Drop-InContact for price
View Datasheet →LM2904DGKR Maximum Ratings & Electrical Characteristics
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Output Type | Push-pull |
| Common-Mode Input Range | Extends to ground |
| Supply Operation | Single supply or split supply |
| Minimum Stable Gain | 10 V/V |
| Package | 8-pin VSSOP |
| Mounting Type | Surface mount |
LM2904DGKR 8-pin vssop Pin Configuration Guide
Pin configuration for LM2904DGKR (8-pin vssop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LM2904DGKR.
Refer to the datasheet for full pin configuration.
Typical Applications
LM2904DGKR is suitable for 6 applications: Industrial Sensor Signal Conditioning, Power-Supply Feedback Monitoring, Audio Preamplification, Battery-Powered Monitoring, Test and Measurement Instrumentation, Motor and Actuator Control.
Industrial Sensor Signal Conditioning
The LM2904DGKR is well suited to amplifying low-level industrial sensor signals because it combines a 700 kHz gain-bandwidth product with a common-mode input range extending to ground. Each amplifier channel can provide non-inverting gain, inverting gain, filtering, or buffering, allowing a transducer interface to be implemented with fewer discrete stages. The 26 V maximum supply supports compatibility with many 12 V and 24 V control systems. Place the decoupling capacitor close to the supply pins and use a compact, low-noise return path to ground. Verify the sensor’s output range and the required closed-loop gain against the amplifier’s common-mode and output-swing limits before finalizing the circuit.
Recommended
Power-Supply Feedback Monitoring
The LM2904DGKR can monitor a power rail and produce an amplified control or diagnostic signal for an analog controller. Its 26 V maximum supply is useful for higher-voltage feedback nodes, while the common-mode input range extending to ground simplifies measurements near 0 V. One channel may amplify a scaled feedback voltage, and the second can buffer a reference or provide an additional gain stage. The 700 kHz gain-bandwidth product is suitable for slow feedback loops and instrumentation rather than high-frequency compensation. Confirm output swing and load-drive requirements, and connect the bypass capacitor directly across the nearby supply and ground pins to prevent supply ripple from appearing at the amplifier output.
Recommended
Audio Preamplification
The dual LM2904DGKR can support two independent low-frequency audio preamplifier channels in consumer, communications, or instrumentation equipment. Its 700 kHz gain-bandwidth product covers the audio band with useful margin, and the common-mode input range extending to ground is valuable for microphone or line-level signals biased near the lower rail. The two push-pull channels can drive lightweight loads or operate as voltage followers into a higher-current driver stage. Keep input traces short and away from switching regulators, provide local supply bypassing, and verify maximum output swing into the intended load. For low-distortion or wide-bandwidth audio requirements, evaluate a newer low-noise amplifier family instead.
Recommended
Battery-Powered Monitoring
The LM2904DGKR is appropriate for battery-powered condition-monitoring circuits that amplify sensor outputs, compare them with thresholds, or buffer inputs for an embedded controller. Operation from a single supply simplifies dual-channel designs, while split-supply operation supports bipolar signals when required. The common-mode input range extending to ground helps avoid the clipping problems commonly encountered with rail-limited amplifiers at low supply voltages. Because battery systems are efficiency-sensitive, check quiescent current and output-current requirements in the manufacturer datasheet. Use low-leakage protection resistors where necessary, keep the input network compact, and place the supply bypass capacitor close to the device to preserve signal integrity as the battery voltage changes.
Recommended
Test and Measurement Instrumentation
The LM2904DGKR can serve as a general-purpose front-end amplifier, buffer, or active summing element in low-frequency test and measurement equipment. Its 700 kHz bandwidth supports measurement paths below several hundred kilohertz, depending on closed-loop gain, while the 26 V supply rating accommodates higher-range instrumentation. The dual configuration allows one channel to condition the input and the other to amplify a reference or output signal. Stable operation at gain of 10 or more is supported by the device architecture, but unusual gain settings, capacitive loads, and very high source impedances require evaluation. Use a ground plane, short feedback paths, and local decoupling to maintain predictable behavior and minimize measurement error.
Recommended
Motor and Actuator Control
The LM2904DGKR can process low-frequency position, current, and feedback signals around motor-control and actuator systems. Two independent channels may handle command conditioning and feedback amplification, reducing the number of packages on a control board. The 26 V maximum supply is relevant to industrial 24 V systems, and the common-mode input range extending to ground supports feedback nodes near the negative rail. The amplifier should not directly drive high current; instead, use it to amplify a sensor or error signal and drive a suitable transistor or motor-driver stage. Verify supply sequencing, transient margin, output loading, and thermal conditions at the highest expected ambient temperature.
Recommended
Recommended Products Summary
Engineering reference data for LM2904DGKR — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM2904BDGKR | LM2904DGD | LM2904DGKR | LM2904DG | LM2904DG | LM2904DG |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | STMicroelectronics | New Japan Radio | Toshiba |
| Package | 8-pin VSSOP | 8-pin VSSOP | 8-pin VSSOP | 8-pin MSOP/VSSOP | 8-pin VSSOP | 8-pin VSSOP | 8-pin VSSOP |
Key Differentiators
- Higher voltage capability in the upgraded same-family option (vs LM2904DGKR)
- Dual general-purpose channels in a compact surface-mount package (vs LM2904DG from STMicroelectronics)
- Common-mode operation extending to ground (vs LM2904DG from Toshiba)
Design Notes
Place the supply-bypass capacitor immediately beside the LM2904DGKR supply and ground pins. Keep both capacitor connections short and use a low-impedance ground return. Because the VSSOP package is compact, inadequate return-current geometry can increase supply noise or create unintended coupling between the two amplifier channels. Route sensitive input nets away from switching nodes and keep the feedback components close to their corresponding amplifier pins.
Do not apply the LM2904B family’s 36 V rating to the original LM2904DGKR, whose maximum supply is 26 V. Also verify that the signal remains inside the common-mode input range and that the output does not exceed its swing limits at the selected load. When substituting another manufacturer’s LM2904 device, compare channel pin functions, differential input limits, quiescent current, output-current capability, and compensation before approving the replacement.
Use short, guarded input traces and avoid long parallel runs beneath noisy switching or digital signals. For high-impedance sources, minimize leakage from adjacent pins and board contamination because input bias current can create voltage errors. Keep the two channels electrically symmetric when they carry related signals, and use a continuous ground plane where practical. Confirm stability with the intended source impedance, load capacitance, gain setting, and feedback network.
Estimated: internal dissipation is approximately equal to output current multiplied by the supply-to-output voltage difference for each active channel. Use the actual worst-case output current, supply voltage, output voltage, and ambient temperature to assess this value, and account for both channels when they operate simultaneously. The VSSOP thermal performance depends strongly on copper area, board construction, and nearby heat sources, so apply the manufacturer’s thermal information for the final PCB.
Compliance Information
Obtain the current manufacturer compliance declarations for the exact LM2904DGKR orderable part before production release.