LM293ADR - 36 V Dual Comparator | Texas Instruments
MPN: LM293ADR ✓ ActiveLM293ADR Overview
A differential comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The LM293 belongs to the comparator hierarchy within interface ICs, where analog input conditioning is converted into a logic-compatible decision. Its open-collector output allows the output state to be defined by an external pull-up resistor, making the device useful in wired-logic, relay-driving, and open-drain bus interfaces.
The LM293ADR provides several characteristics suited to robust circuit design. Its 36 V maximum supply permits operation in industrial environments, while its rail-to-rail input capability allows comparisons near ground. The manufacturer identifies the output as compatible with TTL, MOS, and CMOS logic. The differential input voltage range can equal the maximum-rated supply voltage, and the device is specified for operation over a 2 V to 36 V total supply range.
The LM293A family uses two independent comparator sections within one package. Each section has inverting and non-inverting inputs, an output, and shared supply connections. The open-collector architecture requires a pull-up resistor when the output must actively drive high. The result is a flexible interface between high-voltage or low-level analog signals and digital control logic without requiring a rail-to-rail push-pull output stage.
Typical applications include overvoltage and undervoltage detection, sensor-threshold conditioning, industrial control interfaces, relay or solenoid drivers, window or level comparators, and open-drain bus signaling. The dual-channel configuration allows two related threshold decisions to be implemented in one package, reducing board area when both channels operate from the same supply.
When designing the circuit, choose the pull-up resistor for the required sink current and logic level, and verify that all input pins remain within the common-mode range at every supply condition. Because the output is open-collector, a floating output can occur without a pull-up. Confirm timing against the application’s threshold-crossing rate and maintain adequate supply decoupling close to the power pin.
This page combines the manufacturer’s electrical and ordering information with package guidance, comparison criteria, sourcing support, and practical application notes to help engineers evaluate the LM293ADR for new and existing comparator designs.
Drop-in alternatives for LM293ADR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM293ADR (same form factor and footprint) — differing in Output Type, Differential Input Voltage Range, Industrial Grade, Logic Compatibility, Operating Temperature Range.
LM393ADR
✅ Drop-InContact for price
View Datasheet →LM393BDR
✅ Drop-In📋 Reference alternative (not in catalog)
LM293BDR
✅ Drop-In📋 Reference alternative (not in catalog)
LM2903BDR
✅ Drop-In📋 Reference alternative (not in catalog)
LM293ADT
✅ Drop-In📋 Reference alternative (not in catalog)
LM293ADR Maximum Ratings & Electrical Characteristics
| Comparator Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Maximum Supply Voltage | 36 V |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | ±38 V |
| Response Time | 300 ns |
| Output Type | Open-collector / open-drain |
| Logic Compatibility | TTL, MOS, and CMOS |
| Input Offset Voltage at 25°C | 2 mV maximum |
| Quiescent Current per Channel | 0.4 mA typical |
| Operating Temperature Range | -25°C to +85°C |
| Package | 8-pin SOIC |
| Mounting Type | Surface mount |
| Product Classification | Dual precision standard comparator |
| Industrial Grade | Yes |
LM293ADR 8-pin soic Pin Configuration Guide
Pin configuration for LM293ADR (8-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LM293ADR.
Refer to the datasheet for full pin configuration.
Typical Applications
LM293ADR is suitable for 6 applications: Industrial Overvoltage Detection, Sensor Threshold Conditioning, Relay and Solenoid Interfacing, Battery Supply Monitoring, Motor and Position Limit Detection, Open-Drain Alarm and Fault Bus.
Industrial Overvoltage Detection
The LM293ADR fits industrial overvoltage detection because each channel can compare a divided feedback voltage against a reference while operating from a supply extending to 36 V. The manufacturer specifies a common-mode input range that includes ground and a differential input range of ±38 V, providing useful range for protected industrial supplies. Its open-collector output can directly pull down a system fault line while an external pull-up establishes the inactive state. The two channels can implement overvoltage and undervoltage thresholds in one 8-pin SOIC package. Because output timing and saturation behavior depend on load and supply conditions, the design should include a suitable pull-up, local supply bypassing, and a defined response time for the protection system.
Recommended
Sensor Threshold Conditioning
The LM293ADR can convert a slowly changing sensor signal into a clean digital threshold event when the signal lies within its common-mode range. The 2 mV maximum input offset at 25°C and 300 ns listed response time are useful figures for assessing small-signal discrimination, although actual accuracy also depends on the reference and feedback network. Two independent channels allow separate rising and falling thresholds or comparison of two sensor outputs. The open-drain output is useful when driving a wired-OR alarm line or a microcontroller input with an adjustable logic pull-up. Place the comparator close to the sensed node when the source impedance is high, and use resistor ratios that keep both inputs inside the allowable common-mode range.
Recommended
Relay and Solenoid Interfacing
The LM293ADR is suitable as the decision stage in relay and solenoid interfaces because its open-collector output can sink the current required by a relay driver transistor. The comparator evaluates a control or feedback signal before enabling the external driver, while the open-drain structure avoids actively driving the load supply. A pull-up resistor on the output establishes the complementary logic state. The 36 V supply capability supports industrial control environments, but the output’s maximum sink current and saturation voltage must be checked against the driver design. Keep the relay coil return current away from sensitive comparator input traces, and provide a separate protection path for inductive transients so switching noise cannot create false threshold crossings.
Recommended
Battery Supply Monitoring
The LM293ADR can supervise a battery-backed or industrial supply by comparing a scaled battery voltage with a reference at each of its two channels. Its 2 V to 36 V operating range accommodates many 24 V nominal systems, while the common-mode range including ground supports low-end monitoring approaches. The open-collector outputs can separately report overvoltage and undervoltage conditions to a controller or fault bus. A pull-up defines the inactive state and allows wired-OR behavior. Because battery systems experience wide transients and changing source impedance, the divider should include filtering and clamping as required. Verify the comparator behavior over the full battery range, temperature range, and startup ramp rather than relying only on a nominal operating point.
Recommended
Motor and Position Limit Detection
The LM293ADR can implement limit-switch and position-sensor interfaces in industrial motor-control systems. One channel can evaluate a normally closed or normally open limit switch, while the other monitors a second direction or stage. The open-collector output supports fail-safe wired logic when an open circuit or missing pull-up is interpreted as a fault. The 2 V to 36 V supply range is useful for systems with protected 12 V or 24 V rails, and the common-mode input range includes ground for switch returns referenced to the lower rail. Route switch wiring away from motor power currents and use filtering on long cables. Confirm that the comparator’s input protection and common-mode limits accommodate the switch transients and supply variation present in the motor environment.
Recommended
Open-Drain Alarm and Fault Bus
The LM293ADR can drive an open-drain alarm bus because each comparator output can pull a shared line low and release it when the input condition changes. This arrangement supports multiple fault sources with a common pull-up and helps represent a wired-OR alarm condition. The two channels can monitor separate rails or produce an upper and lower threshold event. Texas Instruments identifies the output as compatible with TTL, MOS, and CMOS logic. Choose the pull-up voltage for the connected receiver and size the resistor to balance sink current against bus rise time. For safety-related behavior, verify output states during power-up, input overvoltage, and loss of the pull-up so the alarm interpretation remains deterministic.
Recommended
Recommended Products Summary
Engineering reference data for LM293ADR — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM393ADR | LM393BDR | LM293BDR | LM2903BDR | LM293ADT |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SO |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector / open-drain | Open-collector / open-drain | Open-collector / open-drain | Open-collector / open-drain | Open-collector / open-drain | Open-collector |
Key Differentiators
- Two independent threshold channels in a compact SOIC (vs LM393ADR)
- Wide industrial supply capability (vs LM293ADT)
- Ground-referenced input capability (vs LM2903BDR)
Design Notes
Do not treat the LM293ADR output as a push-pull logic output. The open-collector transistor actively pulls the output low, while an external pull-up resistor must establish the high state. Select the pull-up voltage for the connected TTL, MOS, or CMOS receiver, and calculate its resistance from the required sink current and desired rising-edge time. A missing pull-up can leave the output node floating, so include continuity and fault-state analysis in the design review.
Place the supply bypass capacitor close to the VCC and ground pins, and keep comparator input traces short and away from relay, motor, and switching-conductor paths. High-impedance divider nodes require low-leakage components and guarding if contamination or board leakage could shift the threshold. Because the common-mode range includes ground, check the actual lower input limit at the minimum supply rather than assuming every ground-referenced signal remains valid.
Use the manufacturer input offset and timing specifications as the starting point for threshold-error analysis, then include resistor tolerance, reference drift, output saturation, and pull-up rise time in the end-to-end error budget. The listed 300 ns response time is a device characteristic rather than a complete system-delay guarantee. For slow thresholds, add controlled hysteresis to prevent output chatter around the switching point.
The 36 V maximum supply supports industrial environments but does not remove the need for transient protection. Use appropriate fusing, surge suppression, reverse-polarity protection, and input clamping where the supply can experience automotive-like or industrial transients. Keep any protection network outside the comparator’s high-current output path so it does not disturb threshold accuracy or pull-up rise time.
Compliance Information
Texas Instruments identifies LM293ADR as an industrial-grade component, but no exact suffix-specific material-compliance declaration was included. Review current manufacturer compliance documentation before using the device in regulated or automotive equipment.